ENGLISH
Decoration Cover -1-
STEP 1. ASSEMBLE THE FRONT FOOT(C) WITH THE BASE FRAME(A) BY USING THE BOLTS(M1). STEP 2. ASSEMBLY THE REAR FOOT(D) WITH THE BASE FRAME(A) BY USING THE BOLTS(M1). AFTER COMPLETING FIRURE 1, IF THE FLOOR / EQUIPMENT IS NOT EVEN, TURN THE ADJUSTABLE-END CAP(D2) TO THE DESIRED LEVEL IN ORDER TO BALANCE THE FRAME.
STEP 1.CONNECT THE SENSOR WIRE(A14) AND THE COMPUTER CABLE(B4) STEP 2 .ASSEMBLE SUPPORT TUBE(B) WITH THE BASE FRAME(A) BY BOLTS(B7), SPRING WASHERS(B6) AND M8 WASHERS(B5). STEP 3 .EQUIP HANDLE BAR SUPPORT(E1) WITH CENTRAL SUPPORT(B) AND USE WASHER(M7), END CAP(M8) AND SCREW(M9) TO FIX IT. THE SAME WAY TO EQUIP E2. ATTENTION:TAKE CARE WHEN PUSHING THE TUBES TOGETHER THAT THE CABLES AND WIRES ARE NOT PINCHED.
STEP 1.SLIDE THE HAND PULSE SENSORS(G5) THROUGH THE HOLE OF SUPPORT TUBE(B) AND GETTING OUT FROM THE TOP OF THE SUPPORT TUBE. STEP 2.ASSEMBLY THE SMALL HANDLE BAR(G) WITH SMALL HANDLEBAR BRACKET (B2), & SCREWS(B3). STEP 1.CONNECT THE SENSOR WIRES(B4 & G5) WITH THE COMPUTER(H). STEP 2.ATTACH THE COMPUTER ON THE TOP OF THE SUPPORT TUBE AND THEN, PUSH THE COMPUTER DOWNWARD AS DIRECTION 2.
ASSEMPLE HANDLE BAR(F1 & F2) WITH HANDLE BAR SUPPORT(E1 & E2) BY SCREW(M6). STEP 1.EQUIP THE CONNECTION TUBE(A12) WITH THE HANDLE BAR SUPPORT (E2) .ASSEMBLE THE HANDLE BAR SUPPORT WITH THE DECORATION (K1 & K2) WITH THE SCREWS (M2) AND THEN FIX BY POP-PIN (M3). STEP 2.THE SAME PROCEDURE AS LEFT SIDE. **4 SECTION HEIGHT ADJUSTING. THERE ARE 4 POSITION OF SIDE HANDLE BAR FOR DIFFERENT HEIGHT ADJUSTING CHOICE BY POP-PIN(M3).
ASSEMBLE THE FOOTREST(L2) BY SCREW(M4) & NUT(M5). THERE ARE 3 SECTIONS ADJUSTING FOR THE MOVING TRACK. IF YOU FIND THE END CAP OF THE FRONT TUBE AND REAR TUBE ARE NOT NESTLE AGAINST THE GROUND, YOU CAN CHANGE THE ANGLE OF THE END CAP OF REAR TUBE(D2). T O AVOI D T HE BAT T ERY LI FE FROM BEI NG EXHAUST ED EASI LY , T HERE I S 1 PC ADAPT ER PROVI DED. PLEASE PLUG I T AS SHOWN ABOVE.
STEP 1.HOLD THE SMALL HANDLE BAR AND PUSH DOWNWARD AS DIRECTION 1. STEP 2.MOVE THE MACHINE BY THE TRANSPORT ROLLER ATTACHING ON THE FRONT FOOT.
-8-
A65 A66 -9-
PARTS LIST P/N A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 A18 A19 A20 A21 A22 A23 A24 A25 A26 A27 A28 A29 A30 A34 A35 A36 A37 A38 A39 A40 A41 A42 A43 A44 A45 A46 A47 A48 A49 A50 A51 A52 A53 A54 A55 A56 A57 DESCRIPTION BUSHING FOOTREST SUPPORT(L) FOOTREST SUPPORT(R) WASHER SPRING WASHER ALLEN HEAD BOLT M8x20mm PEDAL TUBE WELDMENT SHAFT WASHER SPRING WASHER M8 ALLEN HEAD BOLT M8x25mm WASHER CONNECTION TUBE END CAP SENSOR WIRE BASE FRAME BEARING CLIP WHEEL AXLE MAGNET SCREW DRIVING PULLEY ROUN
PROGRAMMABLE COMPUTER INSTRUCTIONS FUNCTION BUTTONS MODE: Press MODE to enter one of the following programs: MANUAL, PROGRAM, USER, or TARGET HEART RATE; press MODE to choose a tension level; or press MODE to preset numbers in TIME, DISTANCE, CALORIE, WATT and PULSE. START/STOP: To START or STOP computer UP: To select the next program; to increase tension level; or to increase the preset number DOWN: To select the previous program; or to reduce tension level; or to decrease the preset number.
PULSE: Hold both hands on the grips for 30 seconds, the current heart rate in Beats Per Minute (BPM) will be displayed on the computer. When using a preset target pulse the alarm will beep when the heart rate reaches the preset BPM. (The heart rate information is a comparison guide for exercise and should not be used for medical purposes.) COMPUTER OPERATION Step 1 Step 2 Step 3 Step 4 Start pedaling or press MODE to start computer. If there is no motion for 4 minutes, the computer will shut off.
P1 – P12 PROGRAM The PROGRAM includes 12 profiles (P1-P12) as shown below. Once a profile has been selected the tension level can be adjusted before or during exercise. Select one of P1-P12 program by using UP and DOWN and press MODE. Then select a tension level by using UP and DOWN and press MODE. Press MODE to select the values on TIME, DISTANCE, CALORIE and/or PULSE and use UP and DOWN to make changes.
USER PROGRAM User can customize an exercise program by pressing MODE to select USER PROGRAM. Using UP and DOWN to adjust the tension level in each of 16 segments, and then press MODE to select. Press the START/STOP twice to preset the TIME, DISTANCE, CALORIE and/or PULSE if desired, otherwise press START/SPOP to begin exercise. (Customized program will be stored in the user program and can be changed if desired.) TARGET HEART RATE PROGRAM After selecting TARGET H.R.
BATTERY INSTALLATION The computer needs 4 size “C” batteries to be installed in both compartments located on the back of the computer, as shown below. Note: 1. When there is no signal being transmitted into the computer for 4 minute, the display will shut off automatically, and previous data will be stored. Press any button to restart the computer. 2. Remove the batteries and re-install when the LCD displays improperly.
