EXHIBIT USER'S MANUAL IN ACCORD WITH 47 C.F.R. §0.459, APPLICANT REQUESTS CONFIDENTIALITY OF ALL DOCUMENTS CONTAINED WITHIN THIS EXHIBIT.
I: TORE TECHNOLOGIES COMPANY AX-550 Development System Actual Size USER’S MANUAL Iterate Technologies Company 101 W. Robert E. Lee Blvd., Suite 404 (504) 282-1639 fax (504) 282-0999 web site www.itero.
INTRODUCTION: This manual provides an overview of the use and operation of the AX-550 Development System. The AX-550 provides state of the art, spread spectrum communication capabilities at narrow band cost. Some of the many advanced product features of the AX-550 include: Feature List AX-550 Credit Card Transceiver Superior communication reliability using direct sequence spread spectrum. -110 dBm Sensitivity @ 19.2 Kb/s with CRC 16 Error Detection/Correction, Excellent Jam Resistance.
AX-550 Credit Card Transceiver with AX-107 Interface Board oo 12VDC Serial Port AX-550 Credit Card External Power c Transceiver Te Power Switch Status 1 IN Remote Status LED AX-107 Interface Board JP1, Mode Select Status LED Figure | Modes of Operation: DEMONSTRATION MODE Overview: ©F HRS Demonstration mode uses both AX-550 transceivers mounted in the AX-107 Interface Boards.
Both AX-550 transceivers and AX-107 Adapters must be configured for Demonstration mode for proper operation. Both units must be powered using either batteries or the wall adapter provided in the development kit, The unit will operate using two Duracell DL123A or equivalent 3 Volt lithium batteries. Four batteries are provided in the AX-550 Development System. Additional batteries can be purchased from most drug stores. The AX-550 is constantly active during Demonstration mode.
APPLICATION DEVELOPMENT MODE Overview: Application Development mode enables the user to connect each transceiver to a PC. The user may then use one of the evaluation software packages provided in the AX-550 Development System or write custom applications for configuring and controlling the transceivers, Application Development Mode requires the Mode Select jumper be set to pins 2 and 3 (away from transceiver). The following application software programs require this configuration Figure 2, .
Mode Select Jumper Figure 2 Hardware Configuration HARDWARE CONFIGURATION: Mode Select Jumper should be connected between pins 2 and 3 for application support. One end of the RIO cable should be connected to the AX-107 Development Adapter and the other end to the RT to DRY adapter. The adapter connects to any 9-pin serial port on a PC. The AX-107 Interface Board operates on either battery power or from wall AC. To supply the AX-107 with AC wall power plug the wall adapter into a 110 Volt wall outlet.
each device will be setup. Once each device is setup, the receiver poll windows should start displaying idle messages. Idle messages are described in detail in the Enhancing Binary Message Protocol (HEMP) document available online through ARTIST Help. The transmitters are also ready to transmit data by using the load transmitter data file. By Dragging the Message Bar on the transmitter menu and selecting “Whole Message” and then selecting repeat the transmitter will transmit a message every x seconds.
AX LASH Teakettle Manna FUR Dan #0824 AAA a sur Rene In order to have multiple connections running at the same time, you can change the RF frequency and spread spectrum channel simply by choosing one with the drop-down boxes at the bottom of Radio Chat. The program on the other end will automatically change channel and frequency to match. Software Development: The CD included with the AX-550 Development System contains two 32 bit Windows © Dynamic Link Libraries (DLLs).
©COPYRIGHT 1998 by Axon Corporation. All rights reserved worldwide. Iterate Corporation 101 W, Robert E. Lee Blvd, Suite 404 New Orleans, LA 70124 Copyright © 1998 Iterate Corporation. All rights reserved. jolter, the jolter logo are trademarks of lore. AX-550, AX-107, ARTIST, VEGA, Win Dana, and Radio Chat are Trademarks of the Axon Corporation, which may be registered in some jurisdictions. All other brand or product names are trademarks of their respective holders. PAIR Wi