Instructions / Assembly

ManualsBrandsSPRAYIT ManualsKitchenLVLP Mini Gravity Feed Spray Gun

- 1 -

Model No. SP-33500

Low Volume Low Pressure (LVLP) Gravity Feed Mini Spray Gun

Please read this Instruction Manual carefully and understand it completely, basic

precautions should be strictly followed to prevent the damage to the tool and injury

to the operator. Retain this manual for further reference.

CONTAIN:

 Description

 Specification and Technical Data

 Important Safety Instruction

 Instructions for Operation

 Maintenance/Storing

 Troubleshooting/Repairs

 Parts List

 Warranty

Summary of content (8 pages)

PAGE 1
Model No. SP-33500 Low Volume Low Pressure (LVLP) Gravity Feed Mini Spray Gun Please read this Instruction Manual carefully and understand it completely, basic precautions should be strictly followed to prevent the damage to the tool and injury to the operator. Retain this manual for further reference.
PAGE 2
Description The SPRAYIT SP-33500 LVLP Gravity Feed Mini Spray Gun can be used for variety of different applications such as Automotive, Industrial, Marine and Wood Working. The LVLP features require less air allowing you to use a smaller air compressor. Using the SPRAYIT SP-33500 reduces overspray and allows you to spray larger surfaces without having to stop. The Low Volume Low Pressure feature allow for more control with less overspray and waste.
PAGE 3
5.Use clean, dry and regulate compressed air rated at 2.0~3.5bar, never exceed maximum permissive operating pressure (see fig 4) 6.Never use homogenate hydrocarbon solvent, which can chemically react with aluminum and zinc parts and chemically compatible with aluminum and zinc pats. 7.Never point gun at you and others at any time. 4 8.Before operating the tool, make sure all the screws & caps are securely tightened in case of leaking; 9.
PAGE 4
Operation 1. Begin spraying. Always keep the gun at right angles to the work . 2. Keep the nozzle about 6 to 12 inches from the work surface. Grip the gun keeping perpendicular with spraying area then move it parallel for several times, Stopping gun movement in mid-stroke will cause a buildup of paint and result in runs. Do not fan the gun from side to side while painting. This will cause a build-up of paint in the center of the stroke and an insufficient coating at each end. 3. Trigger the gun properly.
PAGE 5
 Trouble shooting Symptom Problems Solution Fluttering or spitting 1. 2. 3. 4. 5. Material level tool low. Container tipped too far. Loose fluid inlet connection. Loose or damaged fluid tip/seat. Dry or loose fluid needle packing nut. 6. Air vent clogged 1. 2. 3. 4. 5. 6. Pattern is arc. 1. Worn or loose Fluid nozzle. 2. Material build up on Air cap. 1. Tighten or replace Fluid nozzle. 2. Remove obstructions from holes, but don’t use metal objects to clean it. Pattern is not Evenly spread. 1.
PAGE 6
 Parts -6-
PAGE 7
NO Description NO Description N O Description 1 Air Adj. Screw 16 O-ring 3.5X1.5 31 Cup 2 Air Adj. Knob 17 Spring Washer 32 Filter 3 O-ring 2.5X2.1 18 33 Paint Inlet Joint 4 Flat Washer 19 34 Trigger 5 Air Valve Spring 20 35 Trigger Pin 6 Air Valve 21 36 Round Nut 7 Air Inlet Joint 22 Spring Set 37 Fluid washer 8 Switch Spring 23 Spring 1X0.4 38 Atomization 9 Snap Retainer D=3 24 Needle Spring 39 Gun Washer 10 O-ring 1.
PAGE 8
Warranty Disclaimers and Limitations of Remedies This warranty gives you specific legal right, and you may also have other rights which may vary from State to State.