TABLE OF CONTENTS Introduction ............................................................................................................................. 1 Product Identification .............................................................................................................. 1 Important Safety Instructions .................................................................................................. 2-4 Know Your Pressure Washer ........................................................
IMPORTANT SAFETY INSTRUCTIONS This manual contains information that is important for you to know and understand. This information relates to protecting YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the symbols below. Please read the manual and pay attention to these sections. DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
WARNING--RISK OF FALL HAZARD Use of pressure washer can create puddles and slippery surfaces. Kickback from spray gun can cause you to fall. Keep operating area clear of all persons, pets, and obstacles. Do not operate the product when fatigued or under the influence of alcohol or drugs. Stay alert at all times. Never defeat the safety features of this product. Do not operate machine with missing, broken, or unauthorized parts. Never leave wand unattended while unit is running.
DANGER-- RISK OF CHEMICAL BURN Use of acids, toxic or corrosive chemicals, poisons, insecticides, or any kind of flammable solvent with this product could result in serious injury or death. Do not use acids, gasoline, kerosene, or any other flammable materials in this product. Use only household detergents, cleaners and degreasers recommended for use in pressure washers. Wear protective clothing to protect eyes and skin from contact with sprayed materials.
ASSEMBLY Your pressure washer requires some assembly and is ready for use after it has been properly serviced with the recommended oil and fuel. Tool need open-end wrench 10mm, 14mm, 17mm. 2.1 1. Unpack Pressure Washer. 1.1 Set carton on a rigid, flat surface. Remove all loose parts and packing. Leave pressure washer in carton. Unit is heavy. Do not attempt to lift and remove the pressure washer unit from the carton. 1.
BEFORE USE 1. Add Engine Oil 1.1 Place pressure washer on a flat, level surface. 1.2 Clean area around oil fill and remove yellow oil fill cap. 1.3 Using oil funnel (optional), slowly pour contents of provided oil bottle into 1-1 oil fill opening. 1.4 Replace oil fill cap and fully tighten. NOTICE Improper treatment of pressure washer can damage it and shorten its life. DO NOT attempt to crank or start the engine before it has been properly serviced with the recommended oil.
BEFORE USE 3. Attaching High Pressure Hose to Spray Gun 3.1 Insert the hose fitting pin into the gun fitting port. 3.2 Turn the swivel nut clockwise tightly on the gun male fitting. 4. Connecting Spray Wand to Spray Gun 4.1 Thread spray wand onto spray gun. 3.1 5. Connect Hose and Water Supply to Pump 5.1 Similarly, attach other end of high pressure hose to high pressure outlet on pump. Pull down on collar of quick connect, slide onto pump and let go of collar. Pull on hose to be sure of tight connection.
PRESSURE WASHER LOCATION Pressure Washer Location Clearances and Air Movement Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire. Keep at least 5 ft. (1.5 m) clearance on all sides of pressure washer including overhead. Place pressure washer in a well ventilated area, which will allow for removal of deadly exhaust gas. Do not place pressure washer where exhaust gas could accumulate and enter inside or be drawn into a potentially occupied building.
START YOUR POWER WASHER 1. How to Start Your Pressure Washer To start your pressure washer for the first time, follow these instructions step-by-step. This starting information also applies if you have let the pressure washer sit idle for at least a day. 1.1Place pressure washer near an outside water source capable of supplying water at a flow rate greater than 3.5 gallons per minute and no less than 20 PSI at pressure washer end of garden hose. 1.
USE THE NOZZLE TIPS 1. Attaching Pressure Nozzles to Spray Wand 1.1 Pull slip ring on female quick-disconnect fitting of spray wand back. 1.2 Insert male quick-disconnect fitting on pressure nozzle into female quick-disconnect on spray wand. 1.3 Release slip ring on female quick-disconnect and twist. Listen for •lick• to ensure both quick-disconnects are coupled. 1.4 Pull high pressure nozzle and spray wand in opposite direction to ensure they do not separate.
RINSING PRESSURE 1. Pressure Washer Rinsing 1.1 Remove black spray tip from nozzle extension. 1.2 Select and install desired high pressure spray tip following instructions How to Use Spray Tips. 1.3 Keep spray gun a safe distance from area you plan to spray. 1.4 Increase (decrease) spray pressure by turning pressure control knob clockwise (counterclockwise). Use lower pressure to wash items such as a car or boat. Use higher pressure to strip paint and degrease driveways. 1.
MAINTENANCE General Recommendations Cleaning system parts should be kept clean to reduce the risk of overheating and ignition of accumulated debris. Use a damp cloth to wipe exterior surfaces clean. Use a soft bristle brush to loosen caked on dirt, oil, etc. Use a vacuum cleaner to pick up loose dirt and debris. Regular maintenance will improve the performance and extend the life of the pressure washer. Check and Clean Inlet Screen Examine the screen on the pump water inlet.
MAINTENANCE Nozzle Maintenance A pulsing sensation felt while squeezing the spray gun trigger may be caused by excessive pump pressure. The principal cause of excessive pump pressure is a spray tip clogged or restricted with foreign materials, such as dirt, etc. To correct the problem, immediately clean the spray tip following these instructions: 1. Shut off engine and turn off water supply. 2. ALWAYS point spray gun in a safe direction, squeeze spray gun trigger to release retained high water pressure.
STORAGE Long Term Storage Instructions (Fuel in tank) 3. Store chemical hose, high pressure hose and spray Gasoline fuel can become stale when stored over 30 wand so they are protected from damage, such as days. Stale fuel causes acid and gum deposits to form being run over. in the fuel system or crucial carburetor parts. To keep fuel fresh, add a fuel stabilizer liquid additive to fuel.
TROUBLE SHOOTING GUIDE Problem Engine shuts down when running. Solution Probable Cause 1.Out of fuel. 1.Fill fuel tank. 2.Low Engine Oil 2. Add oil. Engine will not start; or starts and runs rough. 1.Rocker switch set to 2.Fuel valve is in "OFF" position. 3.Dirty air cleaner 4.Out of fuel. 5.Stale fuel. 6.Spark plug wire not connected to spark plug. 7.Bad spark plug. 8.Water in fuel. 9.Flooded. 10.Excessively rich fuel/air mixture. 11.Intake valve stuck open or closed. 12.Engine has lost compression.
TROUBLE SHOOTING GUIDE Problem Probable Cause Solution 1.Spray wand not set to low pressure.. 2.Chemical filter clogged. 3.Chemical screen not in chemical. 4.Chemical solution too thick. 5.Pressure hose too long 6.Chemical build-up in chemical injector. 1.See "Using Spray Wand" section. 2.Clean Filter. 3.Ensure end of chemical hose is fully submerged into chemicals. 4.Dilute chemical. Chemical solutions should have same consistency as water. 5.Lengthen water supply hose instead of pressure hose. 6.
UNIT EXPLODED VIEW AND PARTS LIST 9 10 11 12 13 7 8 4 5 6 1 2 3 24 25 26 27 28 29 30 31 32 33 14 15 16 17 18 19 20 21 22 23 1 Gun holder and hose hook 1 18 Rubber foot 2 2 Plain washer 1 19 Plain washer 2 3 Fix nut 1 20 Fix nut 2 4 Grommet 5 21 Engine fix bolt 4 5 Nozzle set 5 22 Spring washer 4 6 Decal 1 23 Plain washer 4 7 Filter 1 24 Fix nut 4 8 Chemical inlet hose 1m 25 Spring washer 4 9 Pump fix bolt 4 26 Axile fix nut 2 10 Spring washer 4
SP54002 SPRAYIT PREASSURE WASHER SPECIFICATIONS Pressure Washer/Hidrolavadora: Model (Modelo) SPRAY IT SP54002 Rated PSI (Presión de Trabajo) 2500 PSI (17.24 MPa) Gallons Per Minute (Galones por Minuto) 2.4 GPM (9.08 l/min) Pump (Bomba) Axial Cam - Brass (Axial Cam - Bronce) Engine / Motór: Engine Type (Tipo de Motór) RT7 Horsepower (Potencia del Motór) 7 hp (5.
WARRANTY Disclaimers, Limitations of Remedies & Exclusions This warranty gives you specific legal right, and you may also have other rights which may vary from State to State.
2 2 2 - 21 -