MOTORIZED SHADES FEATURING Z-WAVE TECHNOLOGY
TABLE OFCONTENTS CONTENTS TABLE OF Getting to Know Your Remotes Two-Button Remote........................................................................ 3 GETTING TO KNOW YOUR REMOTES Single-Channel Remote.................................................................. 4 Multi-Channel Remote.................................................................... 5 Shade Program Button....................................................................
Single-Channel Remote Multi-Channel Remote The single-channel remote can control up to 12 shades at once. The multi-channel remote has 12 available channels. Each channel can include a single shade or multiple shades, maximum of 8 shades on one channel. The remote can control a maximum of 24 shades.
Shade Program Button The program button on the shade’s headrail or motor end lets you move your shade without a remote. It’s also used to perform various programming functions, discussed later in this manual. QUICK START GUIDE Getting Your Remote Ready For the Two-Button or Single-Channel Remote Program button Pull out the paper strip on the back of the remote. MOTOR FOR CELLULAR, PLEATED, AND CLASSIC/FRESCO ROMAN SHADES For the Multi-Channel Remote 1. Remove the battery door. 2.
Knowing Your Shade’s Limits and Home Position To help you get started quickly and easily, we set your shade up with predefined positions. Upper Limit: The highest position your shade can reach. We pick a position that gives you the best view and also protects your shade from damage. Lower Limit: The lowest position your shade can reach. This matches the shade length you ordered.
Assigning Shades to Channels (Multi-Channel Remote Only) If you bought your shades and multi-channel remote at the same time, your shades arrive already paired with your multi-channel remote. However, you’ll need to assign each shade to a channel (or multiple channels) to control them. ADJUSTING YOUR SHADE’S LIMITS AND HOME POSITION Use the instructions in this section to adjust your shade’s upper and lower limits or home (favorite) position. 1.
Adjusting the Upper Limit For the Two-Button or Single-Channel Remote Before You Start 1. On the remote, press and release the UP button. Wait until the shade reaches its preset upper limit. TARGET SHADE 2. Press and hold the UP and DOWN buttons at the same time for 3 seconds. When the remote LED turns amber, release both buttons. The shade will jog. 3. Use the UP or DOWN buttons to move your shade to the new upper limit.
For the Multi-Channel Remote Adjusting the Lower Limit For the Two-Button or Single-Channel Remote 1. O n the remote, press and hold the MENU/RIGHT button for 2 seconds to enter the menu. Before You Start 2. Select SHADE > LIMITS. TARGET SHADE 3. T o proceed past the warning message, press and hold the MENU/RIGHT button for 2 seconds. 4. S croll left and right to select the shade you want to adjust the upper limit for. 5.
For the Multi-Channel Remote 1. O n the remote, press and release the DOWN button. Wait until the shade reaches its preset lower limit. 1. O n the remote, press and hold the MENU/RIGHT button for 2 seconds to enter the menu. 2. Select SHADE > LIMITS. 2. P ress and hold the UP and DOWN buttons at the same time for 3 seconds. When the remote LED turns amber, release both buttons. The shade will jog. 3. U se the UP or DOWN buttons to move your shade to the new lower limit. 4.
Adjusting the Home Position Before you start, decide whether you want to adjust your shade’s upper or lower limit. If you do, make those changes first—moving those limits will reset your home position. 1. O n the remote, use the UP and DOWN buttons to move the shade to your desired home position. Remember that the home position isn’t available with the twobutton remote. For the Single-Channel Remote Before You Start 2. Press and hold the HOME button for 3 seconds.
For the Multi-Channel Remote 1. U se the UP or DOWN buttons to move the shade to your new home position. This can be anywhere between the upper and lower limits. 2. P ress and hold the MENU/RIGHT button for 2 seconds to enter the menu. 3. Select SHADE > SET HOME. 4. S elect the shade you want to set the home position for by scrolling left or right. 5. Press and release the HOME button. PAIRING YOUR REMOTES AND SHADES We preprogrammed your remotes to operate your shades.
Pairing Your Two-Button or Single-Channel Remote Pair a Remote with a Shade You might need to do this if you bought a new remote or shade. These steps apply only to the new remote or shade. The two-button and single-channel remote behave almost identically. The only difference between these remotes is that the single-channel remote has a home button, while the two-button remote doesn’t. In this section, we cover pairing instructions for either the twobutton or single-channel remote.
Pair a Remote with a Group of Shades Pair a Second Remote with a Shade If you want to control a group of shades with one remote, follow these steps. Before you start, decide which remote you want to control the group (known as the group remote). Note that you won’t be able to control an individual shade with the group remote after you perform these steps. You can always adjust the remote’s programming later. 1. R eset the group remote to make sure you start with a clean slate.
Pairing Your Multi-Channel Remote Pair a Remote with a Group of Shades Already Controlled by a Group Remote Pair a Remote with a Shade If you bought a new multi-channel remote and want to pair it with a group of shades that are already controlled by a group remote, follow these steps. You might need to do this if you bought a new shade after your initial purchase. 1. P ress and hold the MENU/RIGHT button for 2 seconds to enter the menu. 1.
Pair a Second Remote with a Shade That’s Already Controlled by a Multi-Channel Remote If you paired a group of shades with a multi-channel remote in the previous section, you might still want to control each individual shade within that group with separate, individual remotes. Remove a Shade from the Multi-Channel Remote You might need to do this if your shade needs to be sent in for repairs. 1. O n the remote, press and hold the MENU/RIGHT button for 2 seconds to enter the menu. 2.
INTEGRATING YOUR SHADES WITH A Z-WAVE® HOME AUTOMATION SYSTEM Your shades and remotes operate using Z-Wave radio technology, which allows you to control your shades with many popular home automation systems. To integrate your shades with a home automation system, you’ll perform three tasks: 1. E xclude: Remove the current pairing between your shades and remotes. 2. I nclude: Add your shades and remotes to the home automation system.
Step 2: (Include) Add Your Shades and Remotes to the Home Automation System NOTE You need to add the shades first and then the remotes to your home automation system. Add Your Shades 1. F rom your home automation system’s user interface, select the option to enroll a new Z-Wave device. Add Your Multi-Channel Remote 1. F rom your home automation system’s user interface, select the option to enroll a new Z-Wave device. See your home automation system’s instructions for details. 2.
Step 3: (Associate) Pair Remotes with Your Shades If you want to be able to control your shades with remotes as well as with your home automation system, follow these steps. Pair a Shade with a Two-Button or Single-Channel Remote TROUBLESHOOTING PROBLEM Replacing Batteries for the Shade Insert eight AA lithium batteries per battery case. 1. O n the remote, press and release the program button on the back. The remote LED will flash green. I need to replace the batteries for my shade or remote. 2.
Troubleshooting, cont. My multi-channel remote isn’t working. If your shade isn’t responding to your multi-channel remote, confirm that you’re on the correct channel for the shade you’re trying to operate. To check the channel, press any button on the remote and note which channel number is displayed. What do the LED colors on my remote mean? If you press a button on your remote and the LED flashes: • Green: The battery in your remote is good.
GLOSSARY TERM DEFINITION MULTI-CHANNEL REMOTE Jog A brief down-and-up movement of the shade. TERM DEFINITION Exclude Removing the current pairing between your shades and remotes. Channel A group of shades that operates at the same time. Each channel can include a single shade or multiple shades. Include Adding your shades and remotes to the same “shade network” (a group of shades and remotes that communicate with each other) or to a home automation system.
FCC Class B Notice ABOUT Z-WAVE ® Z-Wave is a wireless mesh-networking protocol for reliable, intelligent home control of all Z-Wave compatible devices. Z-Wave devices can act as repeaters to create a mesh-network to ensure reliable communication regardless of the manufacturer or type of device. This product can be included and operated in any Z-Wave network with other Z-Wave certified devices from any other manufacturer.
Shades Name/Location Industry Canada Notice This device complies with Industry Canada License-exempt RSS standard(s). Operation is subject to the following two conditions: Channel Assignment Shades on the same channel will operate as a group. 1 Example: Shade 1 - 2 3 4 5 6 7 8 9 10 11 12 Kitchen Shade 1 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
For video tutorials and additional help, visit www.motorization.support Customer Service 1-800-221-6352 motorization.support@springswindowfashions.