Use and Care Manual
5
DANGER
UNPACKING AND MOVING THE ICE MAKER
1. Remove the exterior and interior packaging materials. Check if ice basket and ice scoop
are inside. If any parts are missing, please contact our customer service (800-330-0388).
2. When taking out the unit, pay attention to not tilt unit over 45 degrees.
3. Remove all packaging materials. Clean the tank & ice basket.
4. Put the ice maker on a level & flat countertop without direct sunlight and other sources of
heat (i.e.: stove, furnace, radiator). Make sure that there is at least 6 inches of clearance
around the unit.
5.
Allow at least one hour for the refrigerant fluid to settle before plugging the ice maker in.
6. The appliance must be positioned so that the plug is accessible.
CONNECTING YOUR ICE MAKER
* Improper use of the ground plug can result in the risk of electrical shock. If the power
cord is damaged please call our customer service.
1. This unit should be properly grounded for your safety. The power cord of this appliance is
equipped with a three-prong plug which mates with standard three prong wall outlets to
minimize the po
ssibility of electric shock.
2. Plug your appliance into an dedicated, properly installed and grounded wall outlet. Do not,
under any circumstances, cut or remove the third (ground) prong from the power cord. Any
questions concerning power and/or grounding should be directed toward a certified
electrician.
3. This appliance requires a standard 110-120volt, 60Hz electrical outlet with three-prong
ground.
OPERATING PROCEDURES & MAINTENANCE
!
6
C
C
L
L
E
E
A
A
N
N
I
I
N
N
G
G
A
A
N
N
D
D
M
M
A
A
I
I
N
N
T
T
A
A
I
I
N
N
I
I
N
N
G
G
Y
Y
O
O
U
U
R
R
I
I
C
C
E
E
M
M
A
A
K
K
E
E
R
R
Before using your ice maker, it is strongly recommended to clean it thoroughly.
1. Take out the ice basket.
2. Clean the interior with diluted mild detergent and warm water solution and a soft cloth.
3. Drain the water through the drain cap (located on the bottom front side).
4. Rinse thoroughly with clean water and drain.
5. The outside of the ice maker should be cleaned regularly with a mild detergent and warm
water solution.
6. Dry the inter
ior and exterior with a clean soft cloth.
7. When the machine is not to be used for a long time, clean and drain water. To prevent mold
growth, be sure the interior is completely dry before storage.
O
O
P
P
E
E
R
R
A
A
T
T
I
I
N
N
G
G
I
I
N
N
S
S
T
T
R
R
U
U
C
C
T
T
I
I
O
O
N
N
S
S
1. Lift cover, remove the ice basket and pour clean drinking water into tank.
Keep water level below the MAX water level mark.
2. Press “Power” button on the control panel to begin the ice making cycle.
3. Select the ice cube size by pressing the “Select” button.
4. The ice making cycle lasts approx. 5 to
13 minutes, depending on selection of ice cube size
and the ambient temperature. The recommended room temperature is 50 to 100°F.
5. If water pump can’t inject water, the ice maker will stop automatically, and the “Add Water”
indicator will illuminate. Press “Power” button to turn unit off and add water. Wait at least 3
minutes (to allow refrigerant to settle) then press “Power” button again to start making ice.
6. The ice maker will stop when the ice basket is full, the “Ice Full” indicator will illuminate.
Warning: Direct sunlight or sunlight refl
ection may cause infrared sensor
malfunction. If the unit doesn’t stop when basket is full, move the unit to where there
is no direct sunlight or close curtains and blinds to block sunlight.
7. Change water in the water reservoir every 24 hours to ensure a reasonable hygiene level.
If unit is not to be used for a couple days, drain all the water and dry the tank.