WINDOW / WALL-TYPE ROOM AIR CONDITIONER WA-6011S: 6000 BTU WA-8011S: 8,000 BTU WA-1011S: 10,000 BTU WA-1211S: 12,000 BTU Thank you for your purchase. Before using your air conditioner, please read this manual carefully and keep it for future reference.
CONTENTS 1. SAFETY PRECAUTIONS ………………………………….2 2. IMPORTANT SAFETY INSTRUCTIONS …………………3 3. NORMAL SOUNDS ………………………………………...4 4. AIR CONDITIONER FEATURES …………………………4 5. INSTALLATION INSTRUCTIONS …………………………9 6. CARE AND CLEANING…………………………………...12 7. TROUBLESHOOTING TIPS………………………………13 8. SPECIFICATIONS …………………………………………14 9. REMOTE CONTROL ……………………………………...15 READ THIS MANUAL Inside you will find many helpful hints on how to use and maintain your air conditioner properly.
SAFETY PRECAUTIONS To prevent injury or property damage, the following instructions must be followed. Failure to follow instructions and incorrect operation may cause harm or damage. Warning marks and classification: WARNING Indicates possibility of death or serious injury. CAUTION Indicates possibility of injury or property damage. WARNING Ensure plug is firmly connected to prevent electric shock or fire due to excess heat generation.
NOTE: For some models, the power supply cord with this air conditioner contains a current detection device designed to reduce the risk of fire. Please refer to the section “Operation of Current Device” for details. In the event that the power supply cord is damaged, it cannot be repaired – it must be replaced with a cord from the Product Manufacturer.
High Pitched Chatter High efficiency compressors may have a high-pitched chatter during the cooling cycle. Vibration Unit may vibrate and make noise because of poor wall or window construction or incorrect installation. Sound of Rushing Air At the front of the unit, you may hear the sound of rushing air being moved by the fan. Pinging or Switching Droplets of water hitting condenser during normal operation may cause “pinging or switching” sounds.
AIR CONDITIONER FEATURES (CONTINUED) NOTE: The following instruction represent the Unit Controls, the same instructions can be used for the Remote Control. TO TURN UNIT ON: DO THIS: Press the On/Off button. TO CHANGE TEMPERATURE SETTING: NOTE: Press or hold either Left (<) or Right (>) button until the desired temperature is seen on the display. This temperature will be automatically maintained anywhere between 62°F (17°C) and 86°F (30°C).
NOTE: Press the Mode button to select operating mode. With each press of the button, the mode will go through the following sequence: Auto, Cool, Dry and Fan. The indicator light next to each corresponding mode will illuminate TO SELECT THE OPERATING MODE: DO THIS: Press the Mode button. AUTO mode: When the air conditioner is set in AUTO mode, unit will automatically select Cooling or Fan operation, depending on set and ambient temperature. Set temperature range is 62~86°F.
AIR CONDITIONER FEATURES (CONTINUED) SLEEP FEATURE: DO THIS: Press Sleep button. TIMER: AUTO START/STOP FEATURE: DO THIS: Press Timer button. CHECK FILTER FEATURE: SLEEP feature: When selected in conjunction with COOL mode: Unit will operate at set temperature for 30 minutes. After 30 minutes, unit will increase temperature by 2°F. After another 30 minutes, unit will again increase temperature by 2°F. Unit will operate at the new temperature for 6 hours.
ADDITIONAL THINGS YOU SHOULD KNOW Now that you have mastered the operating procedures, here are some additional features: The Cool circuit has an automatic 3-minute time delay when unit is turned off and on quickly. This protects the compressor from overheating and possible circuit breaker tripping. The fan will continue to run during this time. The LCD is capable of displaying temperature in °F or °C.
Your air conditioner is designed install in standard double hung windows with opening widths of 23 to 36 inches (584mm to 914mm) (See Fig.1) Lower sash must have sufficient vertical opening for installation (Table 1). Side and rear of unit needs to be clear of obstacles to allow airflow through condenser. The rear of the unit must be outdoors, not inside a building or garage.
INSTALLATION NOTE: Top rail and side panels are offset to provide the proper pitch to the rear (5/16”). This is necessary for drainage of water condensation. If the side panels are not used, this pitch still needs to be maintained. 1. Place unit on floor or sturdy table. Install the side panels, the panels are indicated Left or Right – be sure to use the proper panel for each side. When properly installed, the flange for securing the panel to windowsill should face into the room. 1b.
4. Install frame lock between the frame extension and the windowsill. Drive a ¾” (19mm) locking screw through the frame lock and into the sill (Fig.7&8) 5. Insert and secure ½” (13mm) locking screws through frame holes into window sash. (Fig.9&10) 7. Trim foam seal to size and insert in the space between the upper and lower sashes. (Fig.12) Note: To prevent the windowsill from splitting, first drill a 1/8” (3mm) pilot hole. 6.
CAUTION Clean your air conditioner occasionally to keep I looking new. Be sure to unplug the unit before cleaning to prevent chock or fire hazards. Air Filter Cleaning The air filter should be checked at least once a month to see if cleaning is necessary. Trapped particles in the filter can build up and cause an accumulation of frost on the cooling coils Push the vent handle to the Vent Closed position (where applicable). Open the front panel. Grasp the filter by the center and pull up and out.
Before calling for service, review this list, it may save you time and expense. This list includes common occurrences that are not the result of defective workman-ship or materials in this appliance. Air conditioner does not start Wall plug disconnected. Push plug firmly into wall outlet. House fuse blown or circuit breaker tripped. Replace fuse with time delay type or reset circuit breaker. Plug Current Device tripped, press the RESET button.
Water dripping OUTSIDE when unit is cooling Unit removing large quantity of moisture from humid room. This is normal during Remote sensing deactivating prematurely (some models) Remote control not used within range. Place remote control within 20 feet and 180° Room too cold excessively humid days. radius to the front of the unit. Remote control signal obstructed. Remove obstruction Set temperature too low, increase set temperature.
HANDLING THE REMOTE CONTROLLER Location of the remote controller Use the remote control within a distance of 5 meters (5.5 yards) from the appliance, pointing toward the receiver. Reception is confirmed by a beep. CAUTIONS The air conditioner will not operate if curtains, doors or other materials block the signals from the remote controller to the indoor unit. Prevent any liquid from falling into the remote controller. Do not expose the remote controller to direct sunlight or heat.
Operation starts when this button is pressed and stops when the button is pressed again. Press this button to select the desired operation mode from AUTO, COOL, DRY and FAN. Push Pushthis thisbutton buttonto to increase increasethe the temperature settingsetting in 1°C/1 temperature in°F to 30°C/86 1°increase C/1°F increments to°F. 30°C/86°F. Push this button to decrease the temperature setting in 1°C/1°F increments to 17°C/62°F. Push this button to activate the "Auto Start"or"Auto Stop" program.
Cooling and Fan Operation Ensure the unit is plugged in and power is available. 4. Press the ON/OFF button to start the air conditioner. 5. Press the MODE button to select COOL or FAN mode. 6. In COOL mode, press the TEMP UP/DOWN button to set desired temperature. Temperature can be set within the range of 17~30°C/62~86°F in 1°C/1°F increments. 7. Press FAN button to select fan speed in four steps: Auto, Low, Med, or High.
Timer Operation Press the TIMER button to initiate the Auto-Start or Auto-Off program. Timer can be set up to 24 hours. 1. Press the TIMER button to program Timer-On or Timer-Off, the corresponding indicator will illuminate on unit’s control panel. 2. Press or hold the UP/DOWN button to program time in 0.5 hour increments, up to 10 hours, then in 1 hour increments up to 24 hours. Control will count down the remaining time till start/stop. 3.
Your Guarantee If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase, it will be repaired free of charge. This guarantee is subject to the following terms: • Sunpentown must be notified of the fault. • Proof of purchase must be presented to Sunpentown’s nominated representative. • The warranty will be void if the product if modified, misused or repaired by an unauthorized person.
