WA-1351DE: 12,000BTU DUAL-HOSE SYSTEM INSTRUCTIONS MANUAL Thank you for purchasing this Portable Air Conditioner. Before using the unit, please read this instruction manual carefully and keep it for future reference.
Contents Pre para ti on --- --- ---- ---- --- ---- --- ---- 2 Safe t y Precaut ions --- ---- ---- --- ---- --- 3 Cauti ons -- --- ---- ---- --- ---- --- ---- ---- 4 I ns talla ti on ----- ---- --- ---- --- ---- ---- -- 5 Oper ati on --- ---- ---- --- ---- ---- --- ---- - 9 M a i n t e n a n ce --- ---- ---- --- ---- --- ---- - 12 D es ign a n d Com p l ian c e No t es --- ---- --- 13 F au lt s D i ag no si s - --- ---- ---- --- ---- --- 14 So cia bl e Rem ar k --- ---- ---- --- ---- --- -- 14 U
Preparation control panel horizontal louver blade upper air lter (swing automatically) (behind the grille) handle (both sides) upper air intake drain outlet air outlet lower air lter lower air intake power cord outlet power cord buckle Caster power plug socket bottom tray drain outlet front vent control rear 2
Safety Precautions • DO NOT operate an unit that has been dropped or damaged. • Only use the included accessories and specied parts for installation. Using nonstandard parts can cause water leakage, electrical shock, re, injury or property damage. • The unit must be kept free from obstruction to ensure proper function. • DO NOT allow children to play with the air conditioner. • Children must be supervised around the unit at all times.
Cautions • This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play the appliance. Cleaning and user maintenance shall not be made by children without supervision.
Installation Note About Fluorinated Gasses Choosing The Right Location -This air-conditioning unit is a hermetically sealed unit that contains fluorinated gasses. For specic information on the type of gas and the amount, please refer to the relevant label on the unit itself. -Service, maintenance and repair of this unit must be performed by a certied technician.
Installation Window Installation Kit Tools Needed -Medium Philips screwdriver; -Tape measure or ruler; -Knife or scissors; -Saw (optional, to shorten window adaptor for narrow windows) Step One: Preparing the Exhaust Hose Assemblies Press window slider adaptor and unit adaptor onto the exhaust hose. Clips on the adaptors will automatically clamp onto the exhaust hose. Accessories Your Window Installation Kit ts windows 67.5-123cm(26.5-48”) and can be shortened for smaller windows.
Installation Note: Once the exhaust hose assembly and adjustable slider kit are prepared, choose from one of the following installation methods.
Installation Through-the wall connection Note: It is necessary to purchase the following parts for through-the-wall installation: Wall Adaptor (sold separately, please contact Sunpentown at 1-800-330-0388 or visit www.sunpentown.com) Screws & expansion plugs (can be purchased at any hardware store) 1. Prepare a hole in the wall and install Wall Adaptor to the opening (from outside). Secure with 4 expansion plugs and screws. 2. Attach exhaust hose to the Wall Adaptor.
Operation CONTROL PANEL Before you begin, thoroughly familiarize yourself with the control panel and remote controller and all its functions, then follow the symbol for the functions you desire. The unit can be controlled by the unit’s control panel or with the remote controller. Swing button Used to initiate the Auto swing feature. If auto-swing is in function, press the button again to stop the louver at desired angle. Mode button Selects the appropriate operating mode.
Operation LED display FAN operation - Press the MODE button until FAN indicator illuminates. - Press the FAN button to select desired fan speed. - The temperature cannot be adjusted. - Exhaust hose connection is not needed. Displays set temperature, in either °C or °F. Displays auto-timer settings (if any) When unit is in DRY or FAN modes, displays current room temperature.
Operation TIMER function Other features When the unit is operating: - Press the TIMER button to program auto-stop, the TIMER OFF indicator will illuminate. Press the + or buttons to set the time for unit to turn off. - Press the TIMER button again within 5 seconds will allow you to program auto-start. The TIMER-ON indicator will illuminate. Press the + or - buttons to set the time for unit to turn on.
Operation Maintenance Continuous Drainage for DRY mode (optional) - Remove the upper drain plug from back of unit. - Connect drain hose to spout. - Position the open end directly over drain area. Remove the upper drain plug Continuous drain hose Safety Precautions - Always unplug the unit before cleaning or servicing. - DO NOT use ammable liquids or chemicals. - DO NOT wash the unit under running water. - DO NOT operate the machine if power cord is damaged.
Maintenance Design and Compliance Notes Design Notice STORAGE - Drain the unit’s water collection tray according to instructions in the previous section. - Run the appliance on FAN mode for 12 hours in a warm room to dry the interior and prevent mold. - Turn off the appliance and unplug power source. - Clean the air lters according to instructions in the previous section and reinstall. - remove batteries from the remote control.
Problem ossible CauPse P1 Error Code Unit does not turn on when pressing ON/OFF butt on In COOL mode: room temperature is lower than the set temperature Troubleshooting The Water Collection Tray is full. Turn off the unit, drain the water from the Water Collection Tray and restart the unit.
USING THE REMOTE CONTROLLER Remote Controller Specifications Battery Required Signal Receiving Range Operating temperature AAA battery x 2 (not included) 8m -5°C ~ 60°C (23°F ~140°F) SHORT CUT ON/OF F TIMER ON MODE TEMP TIMER OFF FAN SLEEP SWING LED NOTE: Buttons design is based on typical model and might be slightly different from the actual one you purchased, the actual shape shall prevail.
Function Buttons Before you begin using your new air conditioner, make sure to familiarize yourself with the remote control. The following is a brief introduction to the remote control. For detailed instructions on operation of the air conditioner, refer to the Instruction Manual. SHORT CUT Sets and activates your favorite pre-settings. ON/OFF Turns the unit on or off.
Handling the Remote Controller NOT SURE WHAT A FUNCTION DOES? Refer to the Operation Instructions section ofthis manual for a detailed description on howto use your air conditioner. SPECIAL NOTE Button designs on your unit may differ slightly from the example shown. When there are wide differences betweenRemote controller illustration and USER'S MANUAL on function description,the description of USER'S MANUAL shall prevail.
Remote LCD Scr een Indicators Transmission Indicator Lights up when remote sends signal to unit MODE display Displays the current mode, including: AUTO COOL DRY HEAT ON/OFF display Appears when the unit is turned on, and disappears when it is turned off TIMER ON display Displays when TIMER ON is set TIMER OFF display Displays when TIMER OFF is set (Heating models only) FAN Battery display Low battery detection SLEEP display Displays when SLEEP function is activated FAN SPEED display Displays selecte
How To Use The Basic Functions The operating temperature range for the unit is 17°C-30°C (62°F-86°F). You can increase or decrease the set temperature in 1°C(1°F) increments 2 2 3 1 ON/OFF SHORT CUT ON/OFF 4 1 3 TIMER ON MODE TEMP TIMER OFF FAN TIMER ON MODE SLEEP TEMP SWING LED TIMER OFF FAN SLEEP SHORT CUT SWING LED AUTO OPERATION In AUTO mode, the unit will automaticallyselect the COOL, FAN, or DRY mode based on the set temperature. 1. Press the MODE button to select Auto mode. 2.
How To Use The Basic Functions 2 3 ON/OFF 1 MODE SHORT CUT 3 1 TIMER ON TEMP SLEEP SWING SHORT CUT TIMER ON MODE TEMP TIMER OFF FAN ON/OFF 2 LED SLEEP DRY OPERATION 1. Press the MODE button to select DRY mode. 2. Set your desired temperature using the Temp or Temp button. 3. Press the ON/OFFbutton to start the unit. NOTE: FAN SPEED can not be changed in DRY mode. TIMER OFF FAN SWING LED FAN OPERATION 1. Press the MODE button to select FANmode. 2.
How To Use The Basic Functions SETTING THE TIMER FUNCTION Your air conditioning unit has two timer-related functions: TIMER ON: Set the amount of time after which the unit will automatically turn on. TIMER OFF: Set the amount of time after which the unit will automatically turn off. TIMER ON function: Sets amount of time for unit to turn on, such as when you will return home. Press the TIMER ON button. By default, the last set time and "h" (hour) will appear on display.
Setting combined timers: TIMER ON and TIMER OFF at the same Keep in mind that the time periods you set for both functions refer to hours after the current time. For example, say that the current time is 1:00 PM, and you want the unit to turn on automatically at 7:00 PM (which is 6 hours from current time); operate for 2 hours, then automatically turn off at 9:00 PM (which is 8 hours from current time).
Example: Setting the unit to turn on after 6 hours, operate for 2 hours, then turn off (see the figure below).
How To Use The Advanced Functions SLEEP Function The SLEEP function is used to conserve energy , while you sleep. When activated, unit will increase set temperature by 1°C/1°F after 30 minutes; and by another 1°C/1°F after additional 30 minutes. New temperature will be maintained for 7 hours then unit returns to originally set temperature. This ends the SLEEP function. ON/OFF SHORT CUT TIMER ON MODE The SLEEP function is not available in FAN or DRY mode.
Your Guarantee If this product is found to be faulty as a result of faulty materials or workmanship within one year from date of purchase, it will be repaired free of charge. This guarantee is subject to the following terms: · Sunpentown must be notied of the fault. · Proof of purchase must be presented to Sunpentown's nominated representative. · The warranty will be void if the product is modied, misused or repaired by an unauthorized person.