Operator's Manual Model P20-5010/P20-9010 Series IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! Spyker Spreaders Contact Us at 800.972.6130 ©2010 Spyker Spreaders/A Brinly-Hardy Co. 1008198 Rev.
2 54 23 15 22 1 12 27 4 11 26 18 2 33 33 27 9 28 25 21 24 16 49 46 33 11 31 45 28 31 20 30 Handle/Frame Explosion 11 52 24 33 20 32 48 32 24 11 24 53 17 19 12 33 12 10 24 13 12 24 24 3 11 8 5 6 48 14 51 7 15 23 Hopper Explosion 47 34 12 24 33 29 12 12 50 55 16 42 24 56 43 41 57 24 38 37 44 39 36 35 Axle Explosion 50 37 38 50 1008198 Rev.
Item Part # Qty Description Item Part # Qty Description 1 1007081 1 Handle spacer 29 1000198 1 Felt Washer 2 F-577 1 E-Ring 30 1008011 1 Frame 3 1000213 1 Dial 31 1007111 2 Frame brace 4 1008028 1 Gauge Plate 32 1007112 2 Bolt, M6 x 60 SS 5 1008156 1 Adjust handle 33 1007113 5 Bolt, M6 x 35 SS 6 1007086 1 Adjust handle knob side 1 34 1000223 1 Agitator 7 1007087 1 Adjust handle knob side 2 35 1005414 1 Rue Ring Locking Pin 8 1007088 1 Screw, M4
1. Remove two M6 locknuts and M6 x 45mm long bolts to remove pivot and bracket assembly from wheel frame tubes. Set bolts and nuts to the side. You will re-install them in Step 2. Figure 1 2. Insert arm assembly between frame tubes. Re-install pivot and bracket assembly through wheel frame tubes and arm assembly with two M6 x 45mm bolts and M6 locknuts removed in Step 1. Figure 2 1008198 Rev.
3. Rotate control rod and insert into adjustment handle, Figure 3. Remove one nut from end of control rod. Insert control rod into pivot and bracket assembly as shown, Figure 3. Note orientation of bracket. Install second nut finger tight only. Ensure rate gate opens and closes fully. If so, hold the upper control rod nut with wrench and tighten the bottom nut only. Figure 3 4. Tighten nuts and bolts on both sides of spreader at locations shown. Figure 4 5 1008198 Rev.
READ BEFORE USING OPERATE SAFELY Do not wear loose fitting clothing that can get caught in moving parts. Keep bystanders away when you operate this machine. Use this machine for intended purpose only. Always wear eye protection when operating the equipment. Do not let children or an untrained person operate machine. Stay alert for holes in the terrain and other hidden hazards. Keep all parts in good condition and properly installed. Fix damaged parts immediately. Replace worn or broken parts.
READ BEFORE USING Become Familiar With The Operation Of The Spreader Before You Put Material In The Hopper • Practice walking with the spreader, opening and closing the rate gate at the appropriate times. • Travel at a constant speed and operate the spreader lever position. Remember: Open the rate gate after the spreader is in motion at operating speed (about 3 mph, or at a brisk walking pace). • dial setting on the low side. If the setting proves to be too low, cover the area more than one time.
READ BEFORE USING Now You Are Ready To Put Material In The Hopper • WARNING: Avoid Injury! Chemicals can be dangerous. Avoid injury to operators or bystanders. • Make sure the rate gate is in the closed position. • Read chemical container label for handling instructions. A Material Safety Data Sheet (MSDS) should be supplied by the chemical dealer and provides proper safety information. • Wear proper clothing and safety equipment while handling or applying chemicals.
TROUBLESHOOTING Spreader does not sit flat Deflector shut off is binding and will not open/close properly The "feet" or the flattened portion of the spreader hopper support tubes are not bent equally. Shut off plate is jammed with debris. 9 Using a hammer or pliers, bend the feet to be equal with each other. Thoroughly wash out hopper and shut off plates with water. Ensure debris is not stuck between shut off plate and rate gate plate. 1008198 Rev.
NOTE: Dial Settings Are Approximate Only ! Product Particle Size Fine Pellets Mixed Fine Pellets Small Pellets Nitrogen Pellets Medium Size Medium Pellets And Granuals Large Heavy Pellets Lbs. per 1000 sq. ft. Dial Settings Full Rate Once Over Dial Settings Half Rate Twice Over 1 3.6 3.1 2 3 4.0 4.2 3.5 3.7 2 3.7 3.2 4 6 4.7 5.2 4.1 4.5 2 2.2 4 3 4.2 6 4.5 1 3.5 3 2 3 4.2 3.7 4.7 4 2 3.5 3 4 6 4.2 5.2 3.8 4.5 2 3.8 4.9 5.9 3.3 4.1 4.9 4 6 3.
THIS PAGE INTENTIONALLY LEFT BLANK 11 1008198 Rev.
1 YEAR LIMITED WARRANTY This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. For Spyker Spreaders–a Brinly-Hardy Company, products employing metal gear systems, pinion and bevel, these metal gears, only, not inclusive of any other parts or materials, are warranted for the life of the spreader, not to be used for replacement or repair past original purchase.
