OPERATOR'S MANUAL R28-1824 and R76-2436 Rollers R28-1824 R76-2436 Spyker Spreaders Contact us at 800.972.6130 www.spyker.com ! ! IMPORTANT This manual contains information for the safety of persons and property. Read it carefully before assembly and operation of the equipment! ©2021 Spyker Spreaders/A Brinly-Hardy Co.
Table of Contents + Safety TABLE OF CONTENTS SAFETY Safety �������������������������������� 2 PREPARATION: Parts ������������������������������������ 3-4 Assembly ����������������������� 5-7 Use and Care ���������������� 8-9 Operation ���������������������� 8 Maintenance ���������������� 9 Storage ������������������������ 9 Warranty ������������������������ 10 This symbol helps point out important safety precautions throughout this manual.
Part List DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS. PLEASE CALL: 1 (800) 972-6130 18 17 1 10 22 3 9 22 7 11 22 22 13 26 15 15 10 19 14 4 27 16 24 21 3 19 20 21 26 20 Ref. Description 25 12 2 25 21 6 22 20 29 21 18 8 23 5 18 2 20 24 Qty. Part No.
ILLUSTRATIONS ON THIS PAGE ARE TO SCALE FOR FASTER IDENTIFICATION OF HARDWARE DURING ASSEMBLY. Hardware Identifier DO NOT RETURN PRODUCT IF YOU ARE MISSING PARTS.
Assembly 1. 3. On the end of the top hitch plate (5), align the spring clip (4) as illustrated below. Run the #6 Hex Bolt (14) through the spring clip and secure beneath the hitch plate with the #6 Nylon Lock Nut (23). 14 Fig. 1 15 5 A Run two 5/16 x 2" carriage bolts (15) through the hitch plates as illustrated, straddling Bolt A. 23 2 6 Loosely add two 5/16" Nylon Lock Nuts (25) on each bolt. NOTE: After this point, do NOT tighten bolts fully until Step 7.
Assembly 5. Align the scraper bar (8) parallel with the roller drum (but not touching), and across the frame tubes (2) as illustrated. The logo panel faces away from the roller drum. Slide the two U-Bolts (19) in place, straddling the frame tubes (2), running through the scraper bar (8). Addd a 1/4" flat washer (20) and add a 1/4" nylon lock nut (24) to each end of the U-Bolt, but don't tighten fully yet.
Assembly 7. Securing the Hardware Fully secure all of the nuts and bolts that were added on Steps 3, 5 and 6. Fig. 7 8. Insert the handle (1) through D-ring (9) and then slide the handle through the upper hitch plate (5) tabs. 9. Slide a 3/8" washer (22) between the handle and hitch tabs. Run the 3/8" x 2-1/4" hex head bolt (17) through and secure in place with a 3/8" nylon lock nut (26). Attach the roller plug (11) by squeezing tether spring and insert into roller, rotating the plug in place.
Use and Care TO PREVENT INJURY, USE WITH CAUTION: LIFTING HAZARD When the roller is fully loaded with water, it weighs: R28-1824 = 270 lbs R76-2436 = 680 lbs OPERATION • Refer to tractor manual to determine proper towing capacity of your Tractor / Rider. • GROUND CONDITION IS VITAL TO GOOD LEVELING. Soil should be moist, but not muddy. • Refer to your Tractor or Riding Mower owner’s manual for proper towing capacity and safe operation of your towing equipment.
Use and Care MAINTENANCE • The key to years of trouble-free service is to keep your Lawn Roller clean and dry. • Should any rust develop, sand lightly and then paint the area with enamel. • Periodically check all fasteners for tightness. • Lubricate bearings monthly with general purpose lithium grease. Using the grease fittings on the bearings, ensure grease fitting is clean prior to lubricating. If used in a very dirty / wet environment, lubricate bearings weekly.
WARRANTY 1 YEAR LIMITED WARRANTY This is warranted to the original purchaser only. Spyker will replace parts with defects in materials and workmanship, for a period of one year from the date of purchase. Spyker Spreaders will not be liable for any loss, damage or expense including, but not limited to, consequential or incidental damages, arising from the operation, condition or use of the item. The sole and exclusive remedy against Spyker Spreaders being the replacement of the defective parts.
