Install Instructions

ManualsBrandsSquare D ManualsDPDT RelaysPlug In DPDT Timer, off delay, 15 seconds fixed, 120 VAC, 110 VDC

Instruction Bulletin

30072-453-03

Rev. 01, 07/2011

Replaces 30072-453-03, 06/2009

Electronic Timing Relays

Class 9050 Type JCK

Retain for future use.

™

ENGLISH

Introduction This bulletin contains installation and operation instructions for the following

Class 9050 electronic timing relays:

• Type JCK11–59

• Type JCK60

• Type JCK70

Timing Functions The 9050JCK•

is an electronic time delay relay. A microprocessor clocks

the elapsed time, executes the timing functions, and controls the output

relay. Table 1 describes the ten timing functions.

NOTE: All functions may not be available for all JCK timers.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH

Turn off all power supplying this equipment before working on it.

Failure to follow these instructions will result in death or serious

injury.

The “•” indicates that the part number applies to all timing relays specified in this instruction

bulletin.

Table 1: 9050JCK• Electronic Timing Functions

Function Applies To Description Timing Diagram

On Delay

Adjustable Time

Delay

Fixed Time

Delay

When the input voltage is applied, the time

delay begins. Relay contacts change state after

time delay is complete. When the input voltage

is removed, contacts return to their shelf state.

The trigger switch is not used in this function.

JCK1–19 JCK1F•

Single Function Timer

JCK60

Multifunction Timer

JCK70

Interval

Adjustable Time

Delay

Fixed Time

Delay

When the input voltage is applied, the relay

contacts change state immediately and the

timing cycle begins. When the time delay is

complete, or when the input voltage is

removed, contacts return to shelf state. The

trigger switch is not used in this function.

JCK31–39 JCK3F•

Multifunction Timer

JCK70

OFF

DELAY

Input

Voltage

Relay

Contacts

DELAY

OFF

Input

Voltage

Relay

Contacts

Summary of content (4 pages)

PAGE 1
30072-453-03 Rev. 01, 07/2011 Instruction Bulletin Replaces 30072-453-03, 06/2009 ENGLISH Electronic Timing Relays Class 9050 Type JCK Retain for future use. Introduction This bulletin contains installation and operation instructions for the following Class 9050 electronic timing relays: Type JCK11–59 • • • Type JCK60 Type JCK70 . DANGER HAZARD OF ELECTRIC SHOCK, EXPLOSION, OR ARC FLASH Turn off all power supplying this equipment before working on it.
PAGE 2
Electronic Timing Relays Timing Functions Table 1: 30072-453-03 Rev. 01, 07/2011 9050JCK• Electronic Timing Functions (continued) ENGLISH Function Applies To Description Timing Diagram Switch Trigger Adjustable Time Delay JCK21–29 Off Delay Switch and Power Trigger Fixed Time Delay JCK2F• Power Trigger Adjustable Time Delay Fixed Time Delay JCK21PT–29PT JCK2F•PT Multifunction Timers Input voltage must be applied continuously. When the trigger switch closes, the relay contacts change state.
PAGE 3
0072-453-03 Rev. 01, 07/2011 9050JCK• Electronic Timing Functions (continued) Function Applies To Multifunction Timer One Shot Falling Edge JCK70 Multifunction Timer Watchdog JCK70 Multifunction Timer Trigger On Delay JCK70 Description Timing Diagram Upon application of input voltage, the time delay relay is ready to accept trigger signals. When the trigger switch closes, the relay remains in its shelf state.
PAGE 4
Electronic Timing Relays Instruction Bulletin 30072-453-03 Rev. 01, 07/2011 Wiring Diagrams NOTE: ENGLISH 1. The timing relays are not compatible with two-wire AC input sensors. A hard contact relay (for instance, a general-purpose relay) must be interposed. 2. Do not apply DC voltage to the 240 Vac timers. 3. Use the same voltage for the power trigger and control power. Do not use terminal 6 with power trigger devices. 4.