Product Overview

Torque accuracy +/- 15 %
Transient overtorque 120% of nominal motor torque +/- 10 % for 60 s
Asynchronous motor control profile Voltage/frequency ratio, automatic IR compensation (U/f + automatic Uo)
Voltage/frequency ratio, 5 points
Flux vector control without sensor, standard
Voltage/frequency ratio - Energy Saving, quadratic U/f
Voltage/frequency ratio, 2 points
Regulation loop Adjustable PI regulator
Motor slip compensation Adjustable
Not available in voltage/frequency ratio motor control
Automatic whatever the load
Local signalling 1 LED (red) for DC bus energized
Output voltage <= power supply voltage
Isolation Electrical between power and control
Type of cable Without mounting kit: 1 wire(s)IEC cable at 45°C, copper 90 °C / XLPE/EPR
Without mounting kit: 1 wire(s)IEC cable at 45°C, copper 70 °C / PVC
With UL Type 1 kit: 3 wire(s)UL 508 cable at 40°C, copper 75 °C / PVC
Electrical connection VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES: terminal 2.5mm² / AWG 14
L1/R, L2/S, L3/T: terminal 16mm² / AWG 6
Tightening torque 0.6N.m (VIA, VIB, FM, FLA, FLB, FLC, RY, RC, F, R, RES)
2.5N.m, 22 lb.in (L1/R, L2/S, L3/T)
Supply Internal supply for reference potentiometer (1 to 10 kOhm): 10.5 V DC +/- 5 %, <10A, protection
type: overload and short-circuit protection
Internal supply: 24 V DC (21…27V), <200A, protection type: overload and short-circuit protection
Analogue input number 2
Analogue input type VIA switch-configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits
VIB configurable voltage: 0...10 V DC 24 V max, impedance: 30000 Ohm, resolution 10 bits
VIB configurable PTC probe: 0...6 probes, impedance: 1500 Ohm
VIA switch-configurable current: 0...20 mA, impedance: 250 Ohm, resolution 10 bits
Sampling duration 2ms +/- 0.5 ms F discrete
2ms +/- 0.5 ms R discrete
2ms +/- 0.5 ms RES discrete
3.5ms +/- 0.5 ms VIA analog
22ms +/- 0.5 ms VIB analog
Response time FM 2 ms, tolerance +/- 0.5 ms for analog output(s)
FLA, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
FLB, FLC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
RY, RC 7 ms, tolerance +/- 0.5 ms for discrete output(s)
Accuracy +/- 0.6 % (VIA) for a temperature variation 60 °C
+/- 0.6 % (VIB) for a temperature variation 60 °C
+/- 1 % (FM) for a temperature variation 60 °C
Linearity error VIA: +/- 0.15 % of maximum value for input
VIB: +/- 0.15 % of maximum value for input
FM: +/- 0.2 % for output
Analogue output number 1
Analogue output type FM switch-configurable voltage 0...10 V DC, impedance: 7620Ohm, resolution 10 bits
FM switch-configurable current 0...20 mA, impedance: 970Ohm, resolution 10 bits
Discrete output number 2
Discrete output type Configurable relay logic: (FLA, FLC) NO - 100000cycles
Configurable relay logic: (FLB, FLC) NC - 100000cycles
Configurable relay logic: (RY, RC) NO - 100000cycles
Minimum switching current 3mA at 24 V DC for configurable relay logic
Maximum switching current 5A at 250 V AC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)
5A at 30 V DC on resistive load - cos phi = 1 - L/R = 0 ms (FL, R)
2A at 250 V AC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R)
2A at 30 V DC on inductive load - cos phi = 0.4 - L/R = 7 ms (FL, R)
Discrete input type F programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
R programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
RES programmable 24 V DC, with level 1 PLC, impedance: 4700 Ohm
Discrete input logic Positive logic (source) (F, R, RES), <= 5 V (state 0), >= 11 V (state 1)
Negative logic (sink) (F, R, RES), >= 16 V (state 0), <= 10 V (state 1)
Acceleration and deceleration ramps Automatic based on the load
Linear adjustable separately from 0.01 to 3200 s
Braking to standstill By DC injection
2