Instructions / Assembly

ManualsBrandsSquare D ManualsBreaker BoxesHomeline 100 Amp 10-Space 20-Circuit Outdoor Ring-Type Overhead Main Breaker CSED

40270-308-05

Rev. 01, 02/2014

Replaces 40270-308-04 03/2006

Instruction Bulletin

Circuit Breaker Installation for Homeline

Combination Service Entrance Devices

Retain for future use.

™

Introduction

Homeline

Combination Service Entrance Devices are designed to

restrict the installation of more overcurrent devices than that number

for which it was designed. Be advised that the plug-on connection

arrangement for HOMT circuit breakers is different from HOM circuit

breakers.

DANGER

HAZARD OF ELECTRIC SHOCK, EXPLOSION OR ARC FLASH

• Apply appropriate personal protective equipment (PPE) and follow safe electrical

work practices. See NFPA 70E or CSA Z462.

• This equipment must only be installed and serviced by qualified electrical

personnel.

• Turn off all power supplying this equipment before working on or inside equipment.

• Always use a properly rated voltage sensing device to confirm power is off.

• Replace all devices, doors and covers before turning on power to this equipment.

Failure to follow these instructions will result in death or serious injury.

ENGLISH

Summary of content (12 pages)

PAGE 1
Instruction Bulletin 40270-308-05 Rev. 01, 02/2014 Replaces 40270-308-04 03/2006 ENGLISH Circuit Breaker Installation for HomelineTM Combination Service Entrance Devices Retain for future use. Introduction HomelineTM Combination Service Entrance Devices are designed to restrict the installation of more overcurrent devices than that number for which it was designed. Be advised that the plug-on connection arrangement for HOMT circuit breakers is different from HOM circuit breakers.
PAGE 2
Circuit Breaker Installation for Homeline® Combination Service Entrance Devices Instruction Bulletin 40270-308-05 Rev. 01, 02/2014 Double Row Bus Construction ENGLISH Tandem circuit breaker type HOMT may be installed in combination service entrance devices where the bus bar connector has a slot at the centerline of the desired pole space. See Figure 1. NOTICE HAZARD OF EQUIPMENT DAMAGE Do not use excessive force to install a HOMT tandem circuit breaker where no connector slot is provided. See Figure 1.
PAGE 3
40270-308-05 Rev. 01, 02/2014 Circuit Breaker Installation for Homeline® Combination Service Entrance Devices Instruction Bulletin ENGLISH Single Row Bus Construction NOTICE HAZARD OF EQUIPMENT DAMAGE Tandem circuit breaker type HOMT may only be installed in combination service entrance devices where the bus bar connector has a configuration as in Figure 3. Failure to follow this instruction will result in equipment damage.
PAGE 4
Circuit Breaker Installation for Homeline® Combination Service Entrance Devices Instruction Bulletin ENGLISH Figure 5: Figure 6: 1.98 50 1.73 44 1.49 38 1.24 31 .37 9 HOMT Circuit Breaker .98 25 1.97 50 .51 13 1.55 39 .38 10 .99 25 .38 10 HOM Circuit Breaker 40270-308-05 Rev. 01, 02/2014 .99 25 1.73 44 1.86 47 .74 19 .
PAGE 5
40270-308-05 Rev. 01, 02/2014 Circuit Breaker Installation for Homeline® Combination Service Entrance Devices Instruction Bulletin 1. Remove knockouts. Appropriate to knockout pattern, drive center knockout inward or outward. Alternately pry up or drive in outer rings one at a time to opening required. Figure 8: 2. Select the proper cable clamp, or use other approved methods for securing the cable conduit to the enclosure. 3. Install and wire branch circuit breakers.
PAGE 6
Circuit Breaker Installation for Homeline® Combination Service Entrance Devices Instruction Bulletin 40270-308-05 Rev. 01, 02/2014 Identify Circuits Identify branch circuits on directory label or directory stickers. Energize the Circuit NOTE: Before energizing combination service entrance devices, turn main and branch circuit breakers to the OFF position. 1. Turned on power to the combination service entrance device. 2. Turn main circuit breaker ON. 3. Turn on branch circuit breakers.
PAGE 7
40270-308-05 Rev. 01, 02/2014 Boletín de instrucciones Reemplaza 40270-308-04 03/2006 Instalación de interruptores automáticos en bases integrales de medición para acometida Homeline® Conservar para uso futuro. Las bases integrales de medición para acometida Homeline® han sido diseñadas para restringir la instalación de más dispositivos de sobrecorriente que aquellos para lo cual fueron diseñadas.
PAGE 8
Instalación de int. en bases integrales de medición para acometida Homeline® Instruction Bulletin 40270-308-05 Rev. 01, 02/2014 Construcción de barras de dos hileras Es posible instalar interruptores automáticos en tándem tipo HOMT en bases integrales de medición para acometida donde el conector de barras cuenta con una ranura en la línea central justo en el espacio del polo deseado. Vea la figura 1.
PAGE 9
40270-308-05 Rev. 01, 02/2014 Instalación de int. en bases integrales de medición para acometida Homeline® Instruction Bulletin Construcción de barras de una hilera AVISO PELIGRO DE DAÑO AL EQUIPO ESPAÑOL Es posible instalar interruptores automáticos en tándem tipo HOMT sólo en bases integrales de medición para acometida donde el conector de barras tiene una configuración como la que se muestra en la figura 3. El incumplimiento de estas instrucciónes puede causar daño al equipo.
PAGE 10
Instalación de int. en bases integrales de medición para acometida Homeline® Instruction Bulletin Figura 5: Interruptor automático HOM Dimensions: in. [mm] 0,99 25 0,38 10 Figura 6: 1,98 50 1,73 44 1,49 38 1,24 31 0,37 9 40270-308-05 Rev.
PAGE 11
40270-308-05 Rev. 01, 02/2014 Instalación de int. en bases integrales de medición para acometida Homeline® Instruction Bulletin Preparación para la instalación 1. Retire los discos removibles. Según el diseño de discos removibles, utilice un destornillador para hacer palanca y extraer los discos exteriores uno por uno hasta obtener la abertura necesaria. ESPAÑOL Figura 8: 2.
PAGE 12
Instalación de int. en bases integrales de medición para acometida Homeline® Boletín de instrucciones 40270-308-05 Rev. 01, 02/2014 3. Empuje el interruptor hacia dentro hasta que las mordazas enchufables encajen firmemente sobre el conector de barras. 4. Instale los cables. Identificación de los circuitos Identifique los circuitos derivados y anote su identificación en la etiqueta o calcomanías del directorio.