User Manual

22
Front Derailleur Adjustment Front Derailleur Adjustment Front Derailleur Adjustment
Front Derailleur Adjustment Front Derailleur Adjustment Front Derailleur Adjustment
Front Derailleur Adjustment Front Derailleur Adjustment Front Derailleur Adjustment
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Use a 2.5 mm hex
wrench to adjust the low
limit screw so there is .5
mm between the chain
and the outside edge of
the rear derailleur.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
Measure the gap
between the tallest teeth
of the large chainring
and bottom edge of the
outer cage plate. The
gap must be 1-2 mm.
If it is not, adjust the
height of the derailleur
(_ & _), then repeat steps
_, __, and __.
12
2.5
L
0.5 mm
13
1-2 mm