User Manual

31
Compliance Compliance Compliance
Compliance Compliance Compliance
Compliance Compliance Compliance
SRAM LLC certifies that this product and its packaging are in compliance with:
R&TTE Directive, the Radio and Telecommunication Terminal Equipment Directive 1999/5/EC
WEEE Directive, the Waste Electrical and Electronic Equipment Directive 2012/19/EU
RoHS Directive, the restriction of the use of certain hazardous substances in electrical and electronic equipment 2002/95/
EC
REACh Directive, the Regulation on Registration, Evaluation, Authorization and Restriction of Chemical Directive 1907/2006/
EC
Batteries and Accumulators and Waste Batteries and Accumulators Directive 2006/66/EU
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may
not cause harmful interference, and (2) this device must accept any interference received, including interference that may
cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15
of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee
that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Industry Canada’s license-exempt RSS standard(s). Operation is subject to the following
two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
The term “IC:” before the radio certification number only signifies that Industry Canada technical specifications were met.
Canadian Department of Communications Compliance Statement:
Firmware Update Dongle - DOC: CAN ICES-3(B)/NMB-3(B) C
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur
de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
Warning: Any changes or modifications not expressively approved by SRAM could void the user's authority to operate this
equipment.
This product is ANT+ certified and complies with the bicycle power ANT+ Device Profile. For a complete listing of ANT+
Certified Products and their specific interoperability, please visit www.thisisant.com.
SRAM LLC WORLD HEADQUARTERS
1000 W. Fulton Market, 4th Floor
Chicago, Illinois 60607
USA
Left Shifter
Model#:00001
FCC ID: C9O-LSBED
IC: 10161A-LSBED
Right Shifter
Model#:00101
FCC ID: C9O-RSBED
IC: 10161A-RSBED
BlipBox
Model#:00201
FCC ID: C9O-BOXED
IC: 10161A-BOXED
Firmware Update Dongle
Model#:12701
FCC ID: C9O-LINKED
IC: 10161A-LINKED
Front Derailleur
Model#:12801
FCC ID: C9O-FDED
IC: 10161A-FDED
Rear Derailleur
Model#:12901
FCC ID: C9O-RDED
IC: 10161A-RDED