Projector CP-X505/CP-X605 User's Manual – Operating Guide Thank you for purchasing this projector. WARNING ŹBefore using this product, please read the "User's Manual Safety Guide" and related manuals to ensure the proper use of this product. After reading them, store them in a safe place for future reference. About this manual Various symbols are used in this manual. The meanings of these symbols are described below.
Content Content About this manual. . . . . . . . . . 1 Content . . . . . . . . . . . . . . . . . . 2 Projector features. . . . . . . . . . 3 Preparations . . . . . . . . . . . . . . 3 Contents of package . . . . . . . . . . . . .3 Fastening the lens cover . . . . . . . . . .3 Part names . . . . . . . . . . . . . . . 4 Projector . . . . . . . . . . . . . . . . . . . . . .4 Control panel . . . . . . . . . . . . . . . . . . .5 Rear panel . . . . . . . . . . . . . . . . . . . . .5 Remote control . . . . . . .
Projector features / Preparations Projector features This projector is used to project various picture signals onto a screen. This projector requires only a minimal amount of space for installation and can produce a large projected image from even a short distance. Preparations Contents of package Please see the “Contents of package” in the “User’s Manual (concise)” which is a book. Your projector should come with the items shown there. Contact immediately your dealer if anything is missing.
Part names Part names Projector (1) Speakers (x 4) ( 37). (2) Focus ring ( 19) (3) Zoom ring ( 19) (4) Lamp cover ( 56) The lamp unit is inside. (5) Lens shift cover ( 19) (6) Horizontal lens shift dial ( 19) (7) Vertical lens shift dial ( 19) (8) Front cover (9) Lens ( 61) (10) Lens cover ( 3) (11) Remote sensors (x 3) ( 14) (12) Elevator feet (x 2) ( 9) (13) Elevator knobs (x 2) ( 9) (14) Filter cover ( 58) 7KH DLU ¿OWHU DQG LQWDNH YHQW DUH inside.
Part names (6) (5) (4) Control panel (1) STANDBY/ON button ( 16) (2) MENU button ( 23) It consists of four cursor buttons.
Part names Remote control (1) Laser pointer ( 13) It is a beam outlet.
Setting up Setting up Install the projector according to the environment and manner the projector will be used in. WARNING ŹPlace the projector in a stable horizontal position. If the projector falls or is knocked over it could cause injury and/or damage to the SURMHFWRU 8VLQJ D GDPDJHG SURMHFWRU FRXOG WKHQ UHVXOW LQ ¿UH DQG RU HOHFWULF shock. • Do not place the projector on an unstable, slanted or vibrational surface such as a wobbly or inclined stand.
Setting up Arrangement Refer to the illustrations and tables below to determine screen size and projection distance.
Setting up Connecting your devices Be sure to read the manuals for devices before connecting them to the projector. Make sure that all the devices are suitable to be connected with this product, and prepare the cables required to connect. Please refer to the following illustrations to connect them.
Setting up NOTE • Be sure to read the manuals for devices before connecting them to the projector, and make sure that all the devices are suitable to be connected with this product. Before connecting to a PC, check the signal level, the signal timing, and the resolution. - Do not connect LAN port to any network that might have the excessive voltage. - Some signal may need an adapter to input this projector.
Setting up Connecting power supply 1. Connect the connector of the power cord to the AC inlet of the projector. 2. Firmly plug the power cord's plug into the outlet. WARNING ŹPlease use extra caution when connecting the power cord, as LQFRUUHFW RU IDXOW\ FRQQHFWLRQV PD\ UHVXOW LQ ¿UH DQG RU HOHFWULFDO VKRFN • Only use the power cord that came with the projector. If it is damaged, contact your dealer to newly get correct one.
Remote control Remote control Laser pointer 7KLV UHPRWH FRQWURO KDV D ODVHU SRLQWHU LQ SODFH RI D ¿QJHU RU URG 7KH ODVHU EHDP ZRUNV and the LASER INDICATOR lights while the LASER button is pressed. Putting batteries Please load the batteries before using the remote control. If the remote control starts to malfunction, replace the batteries. If you will not use the remote control for an extended period, remove the batteries from the remote control and store them in a safe place. back and remove the 1.
Changing the frequency of remote control signal The accessory remote control has the choice of the mode 1 or the mode 2, in the frequency of its signal. If the remote control does not function properly, attempt to change the signal frequency. Please remember that the “REMOTE FREQ.
Remote control Using as a wired remote control LAS IND ER ICA TOR The accessory remote control works as a wired remote control, when the wired control port at the bottom of the remote control connects with the REMOTE CONTROL port on the back of the projector via an audio cable with 3.5 diameter stereo mini plugs. When the remote control signal is hard to reach surely to the projector in the environment, this function is effective.
Power on/off Power on/off Turning on the power STANDBY/ON 0DNH VXUH WKDW WKH SRZHU FRUG LV ¿UPO\ DQG button correctly connected to the projector and the outlet. Remove the lens cover, and set the power switch to the ON position. The power indicator will light up in steady orange ( 63). Then wait several seconds because the buttons may not function for these several seconds.
Operating Operating Adjusting the volume the VOLUME button on the remote control. 1. Press A dialog will appear on the screen to aid you in adjusting the volume. 2. 8VH WKH FXUVRU EXWWRQV Ÿ ź WR DGMXVW WKH YROXPH To close the dialog and complete the operation, press the PUSH ENTER PAGE UP PAGE DOWN ESC MENU RESET POSITION AUTO MAGNIFY MY BUTTON ON 1 VOLUME button again. Even if you do not do anything, the dialog will automatically disappear after a few seconds.
Operating Selecting an input signal (continued) 1. Press the VIDEO button on the remote control to select an input for video signal. Each time you press the button, the projector switches its video input port as below.
Operating Adjusting the zoom and focus 1. Use the zoom ring to adjust the screen size. 2. Use the focus ring to focus the picture. Adjusting the lens shift 1. Focus ring Zoom ring Top 2/5 UP Use the vertical lens shift dial to shift the picture upward or downward. Lens shift cover DOWN the horizontal lens shift dial to 2. Use shift the picture left or right. NOTE • When the vertical lens shift is adjusted, it is recommended to shift the picture upward.
Adjusting the position the POSITION button on the remote control. 1. Press The “POSITION” indication will appear on the screen. 2. 8VH WKH FXUVRU EXWWRQV Ÿ ź Ż Ź WR DGMXVW WKH SLFWXUH position. PUSH ENTER PAGE UP PAGE DOWN ESC MENU POSITION AUTO MAGNIFY MY BUTTON RESET VOLUME When you want to reset the operation, press the RESET button on the remote control during the operation. To complete this operation, press the POSITION button again.
Operating Using the magnify feature the ON button of MAGNIFY on the remote control. 1. Press The “MAGNIFY” indication will appear on the screen (although the indication will disappear in several seconds with no operation), and the projector will go into the MAGNIFY mode. ESC MENU POSITION AUTO MAGNIFY MY BUTTON ON 1 RESET VOLUME MUTE 2.
Operating Temporarily blanking the screen the BLANK button on the remote control. 1. Press The blank screen will be displayed instead of the screen of input signal. Please refer to the BLANK item in SCREEN menu ( 38). To exit from the blank screen and return to the input signal screen, press the BLANK button again.
Operating Using the menu function This projector has the following menus: PICTURE, IMAGE, INPUT, SETUP, AUDIO, SCREEN, OPTION, NETWORK, and EASY MENU. EASY MENU consists of functions RIWHQ XVHG DQG WKH RWKHU PHQXV DUH FODVVL¿HG LQWR HDFK SXUSRVH (DFK RI WKHVH PHQXV LV operated using the same methods. The basic operations of these menus are as follows. the MENU button on the remote control or one of 1. Press the cursor buttons on the projector.
EASY Menu '#5; /'07 =4)$ ? EASY Menu From the EASY MENU, items shown in the table below can be performed. Select an item using the Ÿ ź cursor buttons on the projector or remote control. Then perform it according to the following table. Item ASPECT #52'%6 #761 -';5610' ':'%76' -';5610' -';5610' 2+%674' /1&' 014/#. $4+)*60'55 %1064#56 %1.14 6+06 5*#420'55 9*+52'4 014/#. /+4414 014/#. 4'5'6 (+.6'4 6+/' J .#0)7#)' '0).
EASY Menu EASY Menu (continued) Item BRIGHTNESS CONTRAST COLOR TINT SHARPNESS WHISPER MIRROR Description 8VLQJ WKH Ż Ź EXWWRQV DGMXVWV WKH EULJKWQHVV See the BRIGHTNESS item in PICTURE menu ( 8VLQJ WKH Ż Ź EXWWRQV DGMXVWV WKH FRQWUDVW See the CONTRAST item in PICTURE menu ( 26). 26). 8VLQJ WKH Ż Ź EXWWRQV DGMXVWV WKH VWUHQJWK RI ZKROH FRORU See the COLOR item in PICTURE menu ( 27). 8VLQJ WKH Ż Ź EXWWRQV DGMXVWV WKH WLQW See the TINT item in PICTURE menu ( 27).
PICTURE Menu PICTURE Menu From the PICTURE menu, items shown in the table below can be performed. Select an item using the Ÿ ź cursor buttons on the projector or remote control, and press the Ź cursor button on the projector or remote control, or the ENTER button on the remote control to execute the item.
PICTURE Menu PICTURE Menu (continued) Item Description 8VLQJ WKH Ÿ ź EXWWRQV VZLWFKHV WKH FRORU WHPSHUDWXUH PRGH HIGH DEFAULT HIGH CUSTOM MID DEFAULT MID CUSTOM LOW DEFAULT LOW CUSTOM Hi-BRIGHT-1 DEFAULT Hi-BRIGHT-1 CUSTOM Hi-BRIGHT-2 DEFAULT Hi-BRIGHT-2 CUSTOM To adjust CUSTOM COLOR TEMP Selecting a mode whose name includes ENTER : &86720 DQG WKHQ SUHVVLQJ WKH Ź EXWWRQ RU WKH OFFSET GAIN R G B R G B ENTER button displays a dialog to aid you in adjusting the OFFSET and GAIN of the selec
PICTURE Menu PICTURE Menu (continued) Item Description 8VLQJ WKH Ÿ ź FXUVRU EXWWRQV FKDQJHV WKH DFWLYH LULV FRQWURO PRGH PRESENTATION Ù THEATER Ù TURN OFF ACTIVE IRIS PRESENTATION THEATER TURN OFF Feature The active iris displays the best presentation image for both bright and dark scenes. The active iris displays the best theater image for both bright and dark scenes. The active iris is always open. • 7KH VFUHHQ PD\ ÀLFNHU ZKHQ WKH 35(6(17$7,21 RU 7+($7(5 modes are selected.
IMAGE Menu IMAGE Menu From the IMAGE menu, items shown in the table below can be performed. 6HOHFW DQ LWHP XVLQJ WKH Ÿ ź FXUVRU EXWWRQV RQ WKH SURMHFWRU RU UHPRWH FRQWURO DQG SUHVV WKH Ź FXUVRU EXWWRQ on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. Item /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.
IMAGE Menu IMAGE Menu (continued) Item Description H PHASE 8VLQJ WKH Ÿ ź EXWWRQV DGMXVWV WKH KRUL]RQWDO SKDVH WR HOLPLQDWH ÀLFNHU Right Ù Left • This item can be selected only for an RGB signal or a component video signal. (except 525i (480i), 625i (576i), SCART RGB) H SIZE AUTO ADJUST EXECUTE 30 8VLQJ WKH Ÿ ź EXWWRQV DGMXVWV WKH KRUL]RQWDO VL]H Large Ù Small • This item can be selected only for an RGB signal. • When this adjustment is excessive, the picture may not be displayed correctly.
INPUT Menu INPUT Menu From the INPUT menu, items shown in the table below can be performed. 6HOHFW DQ LWHP XVLQJ WKH Ÿ ź FXUVRU EXWWRQV RQ WKH SURMHFWRU RU UHPRWH FRQWURO DQG SUHVV WKH Ź FXUVRU EXWWRQ on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.'%6 241)4'55+8' 68 8+&'1 04 /+& & ;%5 56+.. %1.
INPUT Menu INPUT Menu (continued) Item Description 8VLQJ WKH Ÿ ź EXWWRQV VZLWFKHV WKH IXQFWLRQ RI WKH &20321(17 (Y, CB/PB, CR/PR) port. COMPONENT Ù SCART RGB When the SCART RGB is selected, the COMPONENT (Y, CB/PB, CR/PR) and VIDEO ports will function as a SCART RGB port. A SCART adapter or SCART cable is required for a SCART RGB input to the projector. For details, contact your dealer. COMPONENT VIDEO FORMAT Set the video format for the s-video port and video port.
INPUT Menu INPUT Menu (continued) Item FRAME LOCK RGB IN Description 8VLQJ WKH Ÿ ź EXWWRQV WXUQV WKH IUDPH ORFN IXQFWLRQ RQ RII TURN ON Ù TURN OFF • This item can be performed only on an RGB signal with a vertical frequency of 50 to 60 Hz. • When the TURN ON is selected, a moving pictures are displayed more smoothly. • This function may cause a certain degradation of the picture. In such a case, please select the TURN OFF. Set the RGB input signal type for the RGB port.
INPUT Menu INPUT Menu (continued) Item Description The resolution for the RGB1 and RGB2 input signals can be set on this projector. ,Q WKH ,1387 PHQX VHOHFW WKH 5(62/87,21 XVLQJ WKH Ÿ ź EXWWRQV DQG SUHVV WKH Ź EXWWRQ 4'51.76+10 The RESOLUTION menu will be displayed. (2) In the RESOLUTION menu select the UHVROXWLRQ \RX ZLVK WR GLVSOD\ XVLQJ WKH Ÿ ź buttons. Selecting AUTO will set a resolution appropriate to the input signal.
SETUP Menu SETUP Menu From the SETUP menu, items shown in the table below can be performed. 6HOHFW DQ LWHP XVLQJ WKH Ÿ ź FXUVRU EXWWRQV RQ WKH SURMHFWRU RU UHPRWH FRQWURO DQG SUHVV WKH Ź FXUVRU EXWWRQ on the projector or remote control, or the ENTER button on the remote control to execute the item. Then perform it according to the following table. Item /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.
SETUP Menu SETUP Menu (continued) Item WHISPER Description 8VLQJ WKH Ÿ ź EXWWRQV WXUQV RII RQ WKH ZKLVSHU PRGH NORMAL Ù WHISPER • When the WHISPER is selected, acoustic noise and screen brightness are reduced. 8VLQJ WKH Ÿ ź EXWWRQV VZLWFKHV WKH PRGH IRU PLUURU VWDWXV MIRROR NORMAL Ù H:INVERT Ù V:INVERT Ù H&V:INVERT If the Transition Detector is TURN ON and MIRROR status is changed, Transition Detector Alarm ( 51) will be displayed when projector is restarted after the power switch is turned off.
AUDIO Menu AUDIO Menu From the AUDIO menu, items shown in the table below can be performed. 6HOHFW DQ LWHP XVLQJ WKH Ÿ ź FXUVRU EXWWRQV RQ WKH SURMHFWRU RU UHPRWH FRQWURO DQG SUHVV WKH Ź FXUVRU EXWWRQ on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 81.7/' 64'$.' $#55 545 919 52'#-'4 #7&+1 5'.
SCREEN Menu SCREEN Menu From the SCREEN menu, items shown in the table below can be performed. 6HOHFW DQ LWHP XVLQJ WKH Ÿ ź FXUVRU EXWWRQV RQ WKH SURMHFWRU RU UHPRWH FRQWURO DQG SUHVV WKH Ź FXUVRU EXWWRQ on the projector or remote control, or ENTER button on the remote control to execute the item. Then perform it according to the following table. Item /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.'%6 .#0)7#)' '0).+5* /'07 215+6+10 $.
SCREEN Menu SCREEN Menu (continued) Item Description 8VLQJ WKH Ÿ ź EXWWRQV VZLWFKHV WKH PRGH IRU WKH VWDUW XS VFUHHQ The start-up screen is a screen displayed when no signal or an unsuitable signal is detected. MyScreen Ù ORIGINAL Ù TURN OFF MyScreen START UP ORIGINAL TURN OFF Feature Screen can be registered by the MyScreen item ( 40). Screen preset as the standard screen. Plain black screen.
SCREEN Menu SCREEN Menu (continued) Item Description MyScreen This item allows you to capture an image for use as a MyScreen image which can be used as the BLANK screen and START UP screen. Display the image you want to capture before executing the following procedure. 1. Selecting this item displays a dialog titled “MyScreen”. It will ask you if you start capturing an image from the current screen.
SCREEN Menu SCREEN Menu (continued) Item Description MESSAGE 8VLQJ WKH Ÿ ź EXWWRQV WXUQV RQ RII WKH PHVVDJH IXQFWLRQ TURN ON Ù TURN OFF When the TURN ON is selected, the following message function works. “AUTO IN PROGRESS” while automatically adjusting “NO INPUT IS DETECTED” “SYNC IS OUT OF RANGE” “Searching….” while searching for the input “Detecting….
OPTION Menu OPTION Menu From the OPTION menu, items shown in the table below can be performed. 6HOHFW DQ LWHP XVLQJ WKH Ÿ ź FXUVRU EXWWRQV RQ WKH SURMHFWRU RU UHPRWH FRQWURO DQG SUHVV WKH Ź FXUVRU EXWWRQ RQ WKH SURMHFWRU RU remote control, or ENTER button on the remote control to execute the item, except for the items LAMP TIME and FILTER TIME. Then perform it according to the following table. /'07 =4)$ ? 2+%674' +/#)' +0276 5'672 #7&+1 5%4''0 126+10 0'6914 '#5; /'07 5'.
OPTION Menu OPTION Menu (continued) Item Description 8VLQJ WKH Ÿ ź EXWWRQV DGMXVWV WKH WLPH WR FRXQW GRZQ WR automatically turn the projector off. Long (max. 99 minutes) Ù Short (min. 0 minute = DISABLE) AUTO OFF AUTO OFF ENABLE AUTO OFF DISABLE 1 0 When the time is set to 0, the projector is not turned off automatically. When the time is set to 1 to 99, and when the passed time with nosignal or an unsuitable signal reaches at the set time, the projector lamp will be turned off.
Item Description This item is to assign one of the following function to MY BUTTON 1 and 2 on the remote control ( 6). &KRRVH RU RQ WKH 0< %87721 PHQX XVLQJ WKH Ż Ź EXWWRQ ¿UVW 7KHQ XVLQJ WKH Ÿ ź EXWWRQV VHWV RQH RI WKH IROORZLQJ IXQFWLRQV to the chosen button. • RGB1: Sets port to RGB1. • RGB2: Sets port to RGB2. • M1-D: Sets port to M1-D. • COMPONENT: Sets port to COMPONENT (Y, CB/PB, CR/PR). • S-VIDEO: Sets port to S-VIDEO. • VIDEO: Sets port to VIDEO. • e-SHOT: Displays the e-SHOT menu ( 54).
OPTION Menu OPTION Menu (continued) Item Description AUTO ADJUST 8VLQJ WKH Ÿ ź EXWWRQV HQDEOHV GLVDEOHV WKH #761 #&,756 automatic adjustment.When DISABLE is selected, '0#$.' &+5#$.' the automatic adjustment feature is disabled, although rough adjustment is automatically performed depending on the basic setting. ENABLE Ù DISABLE • Depending on conditions, such as input image, signal cable to the projector, environment around the projector, etc., the automatic adjustment may not work correctly.
OPTION Menu OPTION Menu (continued) Item Description KEY LOCK 8VLQJ WKH Ÿ ź EXWWRQV WXUQV RQ RII WKH NH\ ORFN IHDWXUH :KHQ TURN ON is selected, the buttons on the projector except the STANDBY/ON button are locked. TURN ON Ù TURN OFF • Please use to avoid a mischief and touching accidentally. This function does not have any effect on the remote control. SERVICE REMOTE RECEIV.
OPTION Menu OPTION Menu (continued) Item Description This projector is equipped with security functions. User registration is required before using the security functions. Please contact your local dealer. 1. Using Security Features 1.1 Inputting the PASSWORD 8VH WKH Ÿ ź EXWWRQV RQ WKH 237,21 PHQX WR VHOHFW 6(&85,7< DQG SUHVV WKH Ź button. The ENTER PASSWORD box will be displayed. The factory default PASSWORD is 2400. This PASSWORD can be changed (1.2 Changing the PASSWORD).
OPTION Menu OPTION Menu (continued) Item Description 1.3 If you have forgotten your PASSWORD 1.3-1 Follow the procedure in 1.1-1 to display the ENTER PASSWORD BOX. 1.3-2 While the ENTER PASSWORD BOX is displayed, press and hold the RESET button on the remote control for about 3 seconds or SUHVV DQG KROG WKH ,1387 DQG Ź EXWWRQV RQ the projector for about 3 seconds. The 10 digit Inquiring Code will be displayed.
OPTION Menu OPTION Menu (continued) Item Description 2.2-4 Move the cursor to the right side of the CHECK PASSWORD BOX and press the /[5ETGGP Ź EXWWRQ WR GLVSOD\ WKH 3$66:25' IRU %1/2.'6' about 20 seconds, please make note of the PASSWORD during this time. '06'4 ':+6 Pressing the ENTER button on the remote control PASSWORD BOX or INPUT button on the projector will return to MyScreen PASS WORD on/off menu.
OPTION Menu OPTION Menu (continued) Item SECURITY Description ,QSXW D SDUW 3,1 &RGH XVLQJ WKH Ÿ ź Ż Ź /RGB and INPUT buttons. 2+0 $1: +PRWV 2+0 %QFG A CONFIRMATION BOX will appear. Reenter the same PIN Code. This will complete the PIN Code 4)$ registration. PIN BOX NOTE: If there is no key input for about 55 seconds while the PIN BOX or the CONFIRMATION BOX are displayed the menu will close.
OPTION Menu OPTION Menu (continued) Item Description 4. Using the Transition Detector Function While the Transition Detector function is ON, when power switch is started to supply to the projector, it might react as below. • Transition Detector alarm shown below might appear on screen, if the projector has been moved or re-installed. • Transition Detector alarm might appear on screen, if the MIRROR setting has been changed.
OPTION Menu OPTION Menu (continued) Item Description 4.3 Setting the Transition Detector off 4.3-1 Follow the procedure in 4.1-1 to display the Transition Detector on/off menu. 4.3-2 Select TURN OFF to display the ENTER PASSWORD BOX (large). Enter the registered PASSWORD and the screen will return to the Transition Detector on/off menu. If an incorrect PASSWORD is input the menu will close. If necessary repeat the process from 4.3-1. SECURITY 4.4 If you have forgotten your PASSWORD 4.
NETWORK Menu NETWORK Menu (continued) Item TIME DIFFERENCE Description Entering the TIME DIFFERENCE : Use the Ÿ ź buttons to enter the TIME DIFFERENCE. Set the same TIME DIFFERENCE as the one set on your PC. If unsure, consult your network administrator. 8VH WKH Ż EXWWRQ WR UHWXUQ WR WKH PHQX after setting the TIME DIFFERENCE. 6+/' &+(('4'0%' 㪞㪤㪫㩷㩷㪇㪇㩷㪑㪇㩷 㪇㩷 DATE AND TIME Entering DATE AND TIME : Use the Ÿ ź Ż Ź EXWWRQV WR HQWHU WKH
NETWORK Menu / Network functions NETWORK Menu (continued) Item Description INFORMATION display : 8VH WKH Ź RU (17(5 EXWWRQV WR YLHZ QHWZRUN LQIRUPDWLRQ DQG FRQ¿UP VHWWLQJV INFORMATION 0'6914- + 0(14/#6+10 0#/' +2 #&&4'55 57$0'6/#5- &'(#7.
Maintenance Maintenance Lamp $ ODPS KDV ¿QLWH SURGXFW OLIH 8VLQJ WKH ODPS IRU ORQJ SHULRGV RI WLPH FRXOG FDXVH the pictures darker or the color tone poor. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them. Preparation of a new lamp and early replacement are recommended. To prepare a new lamp, contact your dealer and tell the lamp type number. Type number = DT00771 Replacing the lamp the projector off, and unplug the power cord. 1.
Maintenance Lamp (continued) WARNING HIGH VOLTAGE HIGH TEMPERATURE HIGH PRESSURE ŹThe projector uses a high-pressure mercury glass lamp. The lamp can break with a loud bang, or burn out, if jolted or scratched, handled while hot, or worn over time. Note that each lamp has a different lifetime, and some may burst or burn out soon after you start using them.
Maintenance $LU ÀOWHU 3OHDVH FKHFN DQG FOHDQ WKH DLU ¿OWHU SHULRGLFDOO\ ,I WKH DLU ¿OWHU EHFRPHV FORJJHG E\ GXVW RU WKH OLNH LQWHUQDO WHPSHUDWXUHV ULVH ZKLFK FRXOG FDXVH D ¿UH D EXUQ RU malfunction to the projector. When the indicators or a message prompts you to FOHDQ WKH DLU ¿OWHU FRPSO\ ZLWK LW DV VRRQ DV SRVVLEOH 1RWH WKDW WKH SURMHFWRU PD\ shut down, when the projector heats too much.
Maintenance $LU ¿OWHU FRQWLQXHG 7XUQ WKH SURMHFWRU RQ DQG UHVHW WKH ¿OWHU WLPH XVLQJ WKH ),/7(5 7,0( LWHP LQ the EASY MENU ( 25). 9. (1) Press the MENU button to display a menu. 3RLQW DW WKH ³),/7(5 7,0(´ XVLQJ WKH ź Ÿ EXWWRQ WKHQ SUHVV WKH Ź EXWWRQ $ dialog will appear.
Maintenance 1. 2. 3. Turn the projector off, and unplug the power cord. Allow the SURMHFWRU WR FRRO VXI¿FLHQWO\ After making sure that the projector has cooled adequately, slowly turn over the projector, so that the bottom is facing. Remove the battery cover. Turn the battery cover in the direction indicated “OPEN” using such as coins. Then the battery cover will come up. While removing the battery cover, pick its knob. Take the old battery out. Press the metal claw of the battery holder.
Maintenance Other care Inside of the projector In order to ensure the safe use of your projector, please have it cleaned and inspected by your dealer about once every year. Caring for the lens ,I WKH OHQV LV ÀDZHG VRLOHG RU IRJJHG LW FRXOG FDXVH GHWHULRUDWLRQ RI GLVSOD\ quality. Please take care of the lens, being cautious of handling. Turn the projector off, and unplug the power cord.
Troubleshooting Troubleshooting Related messages When the unit's power is on, messages such as those shown below may be displayed. When any such message is displayed on the screen, please follow the instructions described below. If the same message is displayed after the remedy, or if a message other than the following appears, please contact your dealer or service company.
Troubleshooting Regarding the indicator lamps /LJKWLQJ DQG ÀDVKLQJ RI WKH 32:(5 LQGLFDWRU WKH /$03 LQGLFDWRU DQG WKH 7(03 indicator have the meanings as described in the table below. Please follow the instructions within the table. If the same indication is displayed after the remedy, or if an indication other than the following is displayed, please contact your dealer or service company. POWER LAMP TEMP Description indicator indicator indicator Turned Turned The projector is in a standby state.
Troubleshooting Regarding the indicator lamps (continued) POWER LAMP TEMP indicator indicator indicator Description The cooling fan is not operating. Blinking In Red or Lighting In Red Turned off Blinking In Red Please turn the power off, and allow the projector to cool down at least 20 minutes. After the projector has VXI¿FLHQWO\ FRROHG GRZQ SOHDVH PDNH FRQ¿UPDWLRQ that no foreign matter has become caught in the fan, etc., and then turn the power on again.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects WARNING ŹNever use the projector if abnormal operations such as smoke, strange odor, excessive sound, damaged casing or elements or cables, penetration of liquids or foreign matter, etc. should occur. In such cases, immediately turn off the power switch and then disconnect the power plug from the power outlet. After making sure that the smoke or odor has stopped, contact your dealer or service company.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect The signal cables are not correctly connected. Correctly connect the audio cables. Reference page 10 The MUTE function is working. Sound does not come out. Restore the sound pressing the MUTE or VOLUME button on the remote control. 17 The volume is adjusted to an extremely low level.
Troubleshooting Phenomena that may be easy to be mistaken for machine defects (continued) Phenomenon Cases not involving a machine defect The brightness and/or contrast are adjusted to an extremely low level. Adjust BRIGHTNESS and/or CONTRAST settings to a higher level using the menu function. Pictures appear dark. Reference page 24, 25, 26 The WHISPER function is working. Select NORMAL for the WHISPER item in the SETUP menu. The lamp is approaching the end of its product lifetime.
:DUUDQW\ $QG $IWHU 6HUYLFH 6SHFLÀFDWLRQ Warranty and after-service ,I D SUREOHP RFFXUV ZLWK WKH HTXLSPHQW ¿UVW UHIHU WR WKH ³7URXEOHVKRRWLQJ´ DQG UXQ through the suggested checks. If this does not resolve the problem, please contact your dealer or service company. They will tell you what warranty condition is applied. 6SHFL¿FDWLRQ 6SHFL¿FDWLRQ Item Product name Liquid Crystal Panel Liquid crystal projector Panel size 2.0 cm (0.
6SHFLÀFDWLRQV 319 6SHFL¿FDWLRQV FRQWLQXHG 154 139 418 >XQLW PP@ 69