User's Manual
Table Of Contents
- 1 Glossary 5
- 2 Notices 6
- 3 Introduction 9
- 4 AIS AtoN product variants 13
- 5 Installation 14
- 6 Transceiver and Sensor Interface connections 19
- 7 Connecting external sensors and systems 23
- 8 Configuration using proAtoN 31
- 9 Operation 50
- 10 Data messages and data sources 51
- 11 Manual configuration 59
- 12 Technical specification 68
- 13 Firmware upgrade procedure 73
- 1 Glossary
- 2 Notices
- 3 Introduction
- 4 AIS AtoN product variants
- 5 Installation
- Figure 3 Typical AIS AtoN transceiver system connections
- Figure 4 Typical AIS AtoN transceiver and Sensor Interface system connections
- 1. Mount the Transceiver in a suitable location on the physical Aid to Navigation.
- 2. Install a VHF antenna according to the manufacturers instructions.
- 3. Install the supplied GNSS antenna.
- 4. Connect any sensor interfaces and light / RACON monitoring signals.
- 5. Connect power to the AIS AtoN transceiver and optional Sensor Interface.
- 6. Configure and commission the AIS AtoN transceiver and optional Sensor Interface via USB (note that this step can be carried out on shore prior to installation in a remote location).
- 5.1 What’s in the box (AIS AtoN transceiver)
- 5.2 What’s in the box (Sensor Interface)
- 5.3 Preparing for installation
- 5.3.1 Tools and wiring accessories
- 5.3.2 VHF antenna and cable
- 5.3.3 PC for configuration
- 5.4 Mounting the AIS AtoN transceiver and Sensor Interface
- 6 Transceiver and Sensor Interface connections
- 6.1 AIS AtoN transceiver connections
- 6.1.1 Power and USB connector
- 6.1.2 18 way Link connector
- 6.1.3 Using the 18 way link connector for direct connection of external equipment
- 6.1.4 VHF antenna connector
- 6.1.5 GNSS antenna connector
- 6.1.6 Earth connection stud
- 6.2 Sensor Interface connections
- 6.2.1 USB connector
- 6.2.2 Sensor 1 connector
- 6.2.3 Sensor 2 connector
- 6.2.4 Link connector
- 7 Connecting external sensors and systems
- 7.1 Connecting sensors and systems to the AIS AtoN Transceiver
- 7.1.1 Light ON/OFF interface
- 7.1.2 Light health interface
- 7.1.3 RACON status interface
- 7.1.4 AtoN Status source and configuration
- 7.1.5 NMEA0183 port
- 7.2 Connecting sensors and systems to the Sensor Interface
- 7.2.1 Isolated analogue inputs
- 7.2.2 Non-isolated analogue inputs
- 7.2.3 Light current sense loop
- 7.2.4 Isolated digital inputs
- 7.2.5 Non-isolated digital inputs/outputs
- 7.2.6 Isolated RS422 / NMEA0183 port
- 7.2.7 RS232 ports
- 7.2.8 SDI-12 interface
- 7.2.9 Relay drive output
- 7.2.10 Input voltage monitor
- 8 Configuration using proAtoN
- 8.1 proAtoN installation
- 8.2 Application layout
- 8.2.1 COM Port selection
- 8.2.2 Read / Write configuration
- 8.2.3 Transceiver configuration mode tabs
- 8.2.4 Sensor configuration mode tabs
- 8.2.5 Synchronisation status
- 8.2.6 Status bar
- 8.3 AIS AtoN transceiver configuration
- 8.3.1 Configuration of ‘Real’ AtoN parameters
- 8.3.2 Message schedule configuration
- Default messages
- Adding additional messages to the schedule
- Access scheme selection
- 8.3.3 FATDMA Schedule configuration
- Channel 1 start UTC
- Channel 1 start slot
- Channel 1 interval
- Channel 2 start UTC
- Channel 2 start slot
- Channel 2 interval
- Example FATDMA schedule
- 8.3.4 RATDMA Schedule configuration
- Channel 1 start UTC
- Channel 1 interval
- Channel 2 start UTC
- Channel 2 interval
- Example RATDMA schedule
- 8.3.5 Virtual AtoN configuration
- Virtual / Synthetic AtoN
- Virtual / Synthetic AtoN Details
- Virtual AtoN schedule
- 8.3.6 Status input configuration tab
- Current status (message 21)
- Light & RACON configuration
- Status bit source
- Status bit logic
- 8.3.7 Alert messages
- BIIT failure actions
- Vessel proximity alert
- Off position alert
- SART Relay Mode
- 8.4 Transceiver diagnostics
- 8.4.1 GNSS tab
- 8.4.2 Serial data tab
- 8.4.3 Diagnostics tab
- AtoN Details
- Power status
- Report generation
- Reported messages
- Active alarms
- 8.5 Sensor configuration
- 8.5.1 Sensor settings
- 8.5.2 ADC settings tab
- Light Current Sense group
- Current Sense ADC Scaling
- Voltage Measurement Scaling
- 8.5.3 Message settings tab
- Message #6 Configuration
- Message #8 Configuration
- 8.5.4 System information
- System Information
- Digital Input Status
- Sensor Health
- 8.5.5 Live data tab
- ADC Data
- 8.6 Other features
- 8.6.1 Offline configuration (applies to transceiver configuration mode only)
- 9 Operation
- 10 Data messages and data sources
- 10.1 Configurations without the Sensor Interface
- 10.2 Configurations with the Sensor Interface
- 10.2.1 AIS AtoN transceiver configuration
- 10.2.2 Configuration of the Sensor Interface
- 10.2.3 Accessing the Sensor Interface shell
- 10.2.4 General Sensor Interface configuration commands
- 10.2.5 Zeni Lite Message #6 configuration commands
- 10.2.6 ADC configuration commands
- 10.2.7 ADC Scaling
- 10.2.8 Message #6 Data Mapping
- 10.2.9 External device support
- 11 Manual configuration
- 11.1 Basic Type 1 AIS AtoN configuration (FATDMA operation)
- 11.2 NMEA0183 / IEC61162 configuration sentences
- 11.2.1 AAR - Configure broadcast rates for AtoN station
- 11.2.2 ACE - Extended general AtoN Station configuration
- 11.2.3 ACF - General AtoN Station configuration
- 11.2.4 AFB - Forced broadcast
- 11.2.5 AFC - AtoN function ID capability
- 11.2.6 AID - MMSI configuration
- 11.2.7 ARW -Configure the receiver turn-on times
- 11.2.8 MCR - Configure proprietary AtoN control
- 11.2.9 MPR - Message configuration of payload re-broadcast
- 11.2.10 TSP - Transmit slot prohibit
- 11.2.11 VER - Version
- 11.3 Proprietary configuration sentences
- 11.3.1 Status Bit Source
- 11.3.2 Status Bit Source Query
- 11.3.3 Light / RACON configuration
- 11.3.4 Light / RACON configuration query
- 11.3.5 General MCR query
- 12 Technical specification
- 12.1 Applicable equipment standards
- 12.2 AIS AtoN transceiver specification
- 12.2.1 Physical
- 12.2.2 Environmental
- 12.2.3 Electrical
- 12.2.4 GNSS
- 12.2.5 TDMA transmitter
- 12.2.6 TDMA receivers
- 12.2.7 Supported AIS messages (transmission)
- 12.2.8 Connector types
- 12.3 Sensor Interface specification
- 12.3.1 Physical
- 12.3.2 Environmental
- 12.3.3 Interfaces
- 12.4 Drawings and dimensions
- 13 Firmware upgrade procedure
- 1. Install and run the 'vxsend' utility (screenshot shown in Figure 33).
- 2. Click the Browse (…) button for the Image file, then navigate to and select the appropriate update file.
- 3. Select the COM port assigned to the AIS AtoN port or AIS AtoN Sensor port, depending on which element is being updated.
- 4. Click 'Start' and wait for the update to complete. Notification is given when the update has completed successfully.
- 5. Power cycle the transceiver and confirm normal operation before it is deployed.
Connecting external sensors and systems
Page 27
Table 3 Pin numbers and functions for the Sensor Interface Sensor 2 connector
The following sections describe the hardware specification and interface for the Sensor Interface connections.
The function of the Sensor Interface (in terms of translation of sensor data to AIS messages) is determined by
the software configuration of the AIS AtoN (see section
8.5 for further details). The default configuration and
supported sensors are described in section 9 of this document. For alternate configurations please refer to the
additional documentation supplied with the product or contact your supplier.
7.2.1 Isolated analogue inputs
The extended sensor interface includes two isolated analogue inputs. These inputs are available on the Sensor
2 connector described in
Table 3. The electrical and measurement specification of these inputs is as follows:
● Differential input range 0 to 36V
● Impedance 620KΩ
● 16 bit resolution
The voltage to be measured should be applied across the differential positive and negative inputs.
7.2.2 Non-isolated analogue inputs
The extended sensor interface includes three non-isolated analogue inputs. These inputs are available via the
Sensor 1 connector described in
Table 2. The electrical and measurement specification for these inputs is as
follows:
Pin Signal name Function and notes
1 SENSOR_ISO_DI_1+ Positive connection for the isolating digital input 1
2 SENSOR_ISO_DI_1- Negative connection for the isolating digital input 1
3 SENSOR_ISO_DI_2+ Positive connection for the isolating digital input 2
4 SENSOR_ISO_DI_2- Negative connection for the isolating digital input 2
5 SENSOR_ISO_DI_3+ Positive connection for the isolating digital input 3
6 SENSOR_ISO_DI_3- Negative connection for the isolating digital input 3
7 SENSOR_ISO_DI_4+ Positive connection for the isolating digital input 4
8 SENSOR_ISO_DI_4- Negative connection for the isolating digital input 4
9 SENSOR_ISO_DI_5+ Positive connection for the isolating digital input 5
10 SENSOR_ISO_DI_5- Negative connection for the isolating digital input 5
11 SENSOR_NON_ISO_DI_1 Non isolating digital input 1
12 SENSOR_NON_ISO_DI_2 Non isolating digital input 2
13 SENSOR_NON_ISO_DI_3 Non isolating digital input 3
14 GROUND Ground for digital inputs
15 ISO_ADC1+ Positive connection for the isolating ADC 1
16 ISO_ADC1- Negative connection for the isolating ADC 1
17 ISO_ADC2+ Positive connection for the isolating ADC 2
18 ISO_ADC2- Negative connection for the isolating ADC 2