Cut Sheet

ManualsBrandsSSAC ManualsControl & Automation20s Timing Relays SS Timer D.O. M

161

www.ssac.com • 800-843-8848 • fax: 605-348-5685

Delay-on-Make/Recycle: (ProgramaCube

Function MRE)

OPERATION: Upon application of input voltage, TD1 begins and the output (relay or solid state) remains

de-energized. At the end of TD1, the TD2 recycle function begins and the output (relay or solid state)

cycles ON and OFF for equal delays. This cycle continues until input voltage is removed.

RESET: Removing input voltage resets the output and time delays, and returns the sequence to the

rst delay.

See: KSPD, KRPD, NHPD, HRPD, TRDU

Delay-on-Make/Single Shot: (ProgramaCube

Function MS)

OPERATION: Upon application of input voltage and the closure of S1, TD1 begins and the output (relay

or solid state) remains de-energized. The output (relay or solid state) energizes at the end of TD1, and

TD2 begins. At the end of TD2, the output (relay or solid state) de-energizes. Opening or reclosing S1

during timing has no affect on the time delays.

RESET: Reset occurs when the time delay is complete and S1 is open. Removing input voltage resets

the time delay, output, and the sequence to the rst delay.

See: KSPD, KRPD, NHPD, HRPD, TRDU

Interval/Recycle: (ProgramaCube

Function IRE)

OPERATION: Upon application of input voltage TD1 begins. At the same time, the TD2 ON time begins

and the output (relay or solid state) energizes. At the end of the ON time, the TD2 OFF time begins and

the output de-energizes. The equal ON time OFF time cycle continues until TD1 is completed at which

time the output de-energizes.

RESET: Removing input voltage resets the time delays, output, and the sequence to the Interval function.

See: KSPD, KRPD, NHPD, HRPD, TRDU

Delay-on-Break/Recycle: (ProgramaCube

Function BRE)

OPERATION: Upon application of input voltage and the closure of S1, the TD2 ON time begins and

the output (relay or solid state) energizes. Upon completion of the ON time, the output de-energizes

for the TD2 OFF time. At the end of the OFF time, the equal ON/OFF cycle repeats. When S1 opens,

the TD1 delay begins. TD1 and TD2 run concurrently until the completion of TD1 at which time, the

TD2 ON/OFF cycle terminates and the output de-energizes. The output energizes if S1 is closed when

input voltage is applied.

RESET: Reclosing S1 during timing resets the TD1 time delay. Removing input voltage resets the time

delay, output, and the sequence to the Delay-on-Break function.

See: KSPD, KRPD, NHPD, HRPD, TRDU

Delay-on-Make

Recycle

Delay-on-Make

Single Shot

Interval

Recycle

Delay-on-Break

Recycle

Interval

Delay-on-Make

Interval/Delay-on-Make: (ProgramaCube

Function IM)

OPERATION: Upon application of input voltage, the output (relay or solid state) energizes and TD1

begins. At the end of TD1, the output de-energizes and TD2 begins. At the end of TD2, the output energizes.

RESET: Removing input voltage resets the time delays, output, and the sequence to the rst delay.

See: HRPD, KRPD, KSPD, NHPD, TRDU

Single Shot/Recycle: (ProgramaCube

Function SRE)

OPERATION: Upon application of input voltage and the closure of S1, TD1 begins. At the same time,

the TD2 ON time begins and the output (relay or solid state) energizes. Upon completion of the ON

time, the output de-energizes for the TD2 OFF time. At the end of the OFF time, the equal ON/OFF

cycle repeats. TD1 and TD2 run concurrently until the completion of TD1 at which time, the TD2 ON/

OFF cycle terminates and the output de-energizes. Opening or reclosing S1 during timing has no affect

on the time delays. The output will energize if S1 is closed when input voltage is applied.

RESET: Removing input voltage resets the time delay, output, and the sequence to the rst delay.

See: HRPD, KRPD, KSPD, NHPD, TRDU

Single Shot

Recycle

Single Shot/Lockout: (ProgramaCube

Function SL)

OPERATION: Upon application of input voltage and momentary or maintained closure of S1, the output

(relay or solid state) energizes and TD1 single shot time delay begins. The output relay de-energizes at

the end of TD1 and the TD2 lockout time delay begins. During TD2 (and TD1) closing switch S1 has no

effect on the operation. After TD2 is complete, closing S1 starts another operation. If S1 is closed when

input voltage is applied, the output energizes and the TD1 time delay begins.

RESET: Removing input voltage resets the time delays and the output and returns the cycle to the rst

delay.

Single Shot

Lockout

Timer Functions

Two Functions in One Timer

Appendix A - Timer Functions