Data Sheet

ManualsBrandsSST SENSING Ltd. ManualsActive ComponentsSST SENSING Ltd. Fluid level gauge LLC 210 D 3-002 LLC210D3-002 Operating voltage (range): 4.5 - 15.4 V DC 1 pc(s)

OUTPUT VALUES

Output Voltage

(Vout): lout = 1A

Vs = 4.5—15.4V

Output High Vout = Vs - 1.5V max

Output Low Vout = 0V + 0.5V max

Output Voltage (Vout): lout = 1A

Vs = 8—30V

Output High Vout = Vs - 1.8V max

Output Low Vout = 0V + 0.7V max

BENEFITS

· High power

· Industrial supply voltage

· Direct load drive design

TECHNICAL SPECIFICATIONS

Supply voltage (Vs) 4.5V

to 15.4V

or 8V

to 30V

Supply current (ls) 2.5mA max. (Vs = 15.4V

)

or 7.5mA max. (Vs = 30V

)

Output sink and source

current (lout) 1A

Operating temperatures Standard: -25°C to +80°C

Extended: -40°C to +125°C

Storage temperatures Standard: -30°C to +85°C

Extended: -40°C to +125°C

Housing material

1, 2

Polysulfone or Trogamid®

Sensor termination 20AWG, 250mm PTFE

wires, 8mm tinned

FEATURES

· Liquid level switches that can detect almost any liquid type;

oil or water based

· Choice of material; Polysulfone (standard) or Trogamid®

· Choice of threads

DATA SHEET

Liquid Level Switches

Optomax Industrial Series

1) Above +85°C, Trogamid is suitable for water based liquids. Oil based liquids can cause deformation of the sensing tip

and must be tested for compatibility.

2) Before use check that the ﬂuid in which you wish to use these devices is compatible either with Polysulfone or

Trogamid®.

3) Voltages applicable to output value stated.

NOTES

Housing/

Mounting

Output Type / Logic

Supply

Voltage

Output

Current

Temp

Summary of content (4 pages)

PAGE 1
DATA SHEET Liquid Level Switches Optomax Industrial Series FEATURES · Liquid level switches that can detect almost any liquid type; oil or water based · · Choice of material; Polysulfone (standard) or Trogamid® Choice of threads Housing/ Mounting · · · Output Type / Logic Supply Voltage Output Current BENEFITS OUTPUT VALUES High power Output Voltage3 (Vout): Vs = 4.5—15.
PAGE 2
OUTLINE DRAWING HOUSING SPECIFICATIONS All dimensions shown in mm. Tolerances = ±1mm. Housing Series LLx2x0 Series Thread 2x0 6x0 7x0 M12x1x8g with hex nut1 1/2” SAE with O-ring1 1/4” NPT2 Pressure3 7 bar /101 psi maximum Tightening Torque 1.5 Nm / 13.26 in-lbs maximum LLx6x0 Series ELECTRICAL INTERFACE LLx7x0 Series NOTES 1) 2) 3) Hex nut and ONPT version can be sealed with PTFE tape. When correctly sealed.
PAGE 3
CIRCUIT DIAGRAMS In order to suit any application, these sensors have been designed with various output circuit conﬁgurations. They are identiﬁed by the 3-digit code at the end of the part number as shown in Order Information. CAUTION: Take care when connecting loads. The minimum load impedance should not exceed Vs/max output current. Note: Shorting the output to Vs or 0V will result in irreparable damage to the sensor.
PAGE 4
ORDER INFORMATION Generate your speciﬁc part number using the convention shown below. Use only those letters and numbers that correspond to the sensor and output options you require — omit those you do not. L L X X X 0 D 3 X X X - X X X Housing Material Housing Type Operating Temp.