Installation Guide

STEP 1 | Floor Glides Installation (If Applicable)
Lay the cabinet down carefully so that the front face of the
vanity is facing upward.
TO ENSURE THAT YOUR INSTALLATION GOES SMOOTHLY, PLEASE READ THESE INSTRUCTIONS THOROUGHLY PRIOR TO STARTING.
WARNING & CAUTION
Failure to follow warnings and cautions could result in serious injury. Do not exceed the maximum load capacity.
Do not stand on cabinet. Use cabinet on level ground.
WARNING: Base cabinet supports a maximum weight of 200lbs. Exceeding maximum weight limit will compromise the integrity of the
cabinet structure and could cause the cabinet to fail.
CAUTION: Do not hang from the cabinet.
STEP 7 | Hinge/Door Adjustment (If Applicable)
The door alignment was set in the factory, but it could have shifted during transit.
If adjustment is needed, follow the instructions provided in the adjacent chart.
A
Used to adjust
door height
A
B
Used to adjust
gaps between doors
B
Used to adjust between
door and cabinet
C
C
CABINET FRONT VIEW CABINET FRONT VIEW CABINET SIDE VIEW
Fig.#3
right spring clip
Fig.#4
left spring clip
STEP 4 | Full Extension Drawer Glide Removal (If Applicable)
1. Open the drawer as far as possible.
2. Identify the plastic spring clips located in both slides.
3. At the same time, press the right slide spring clip downward and the left
slide spring clip upward (Fig.#3 & Fig.#4).
4. Once both spring clips are held in the indicated position, pull the drawer
straight out.
Epoxy Drawer Glide Removal
(If Applicable)
1. Open the drawer as far as possible.
2. Lift the front part of the drawer to
reach a 30º angle position.
3. Pull the drawer straight out.
Fig.#1
1"
Fig.#2
1"
For cabinets 30" WIDE or SMALLER
Using a soft hammer install 4 floor glides as shown in Fig.#1.
For cabinets
WIDER than 30"
Using a soft hammer install 8 floor glides as shown in Fig.#2.
STEP 5 | Vanity Top Installation
1. Set the vanity top on top of the vanity base, checking the location of the p-trap and drain.
2. Remove the top and install the faucet per manufacturer’s installation instructions.
3. Hand tighten the pop-up drain with a wrench. Be careful not to over-tighten the pop-up drain. Over tightening may cause cracks on the marble top.
4. Apply a thin bead of silicone compound around the vanity base and set the vanity top carefully in place. Remove any excess silicone compound with a wet rag.
5. Install the faucet, water lines and P-trap according to manufacturer’s installation instructions.
SILICONE
Epoxy Drawer Glide Installation (If Applicable)
1. In a 30º angle position, introduce the drawer in the base cabinet making
sure the drawer slide wheels are above the vanity slide wheels.
2. Close the drawer completely and to ensure it has been properly installed,
open it as far as possible.
STEP 6 | Full Extension Drawer Glide Installation (If Applicable)
1. Close completely both slides attached to the vanity.
2. Move the component of the slides with ball bearings to the front of the slides, maintaining
the slides completely closed.
3. Carefully line up the slides of the drawer box with the slides in the base cabinet and close
the drawer all the way to the back.
4. Open the drawer completely to ensure it is properly installed.
STEP 8 | Drawer Front Adjustment (If Applicable)
1. Remove decorative hardware from the drawer front.
2. Hold drawer front in place and slightly loosen both alignment screws.
3. Move the drawer front left, right, up or down to desired position for alignment.
4. While holding the drawer front in place, tighten the alignment screws securely.
5. Install the decorative hardware to the outside of the drawer front.
alignment
screws
drawer box
decorative hardware
drawer front
alignment screws
Mirror Installation (If Included)
1. Determine the desired location of the mirror. Use appropriate screws or wall anchors (not included) to hang mirror.
2. Be sure the hanging hardware is rated to handle the weight of the mirror. The mirror weight is approximately 20 lbs.
Installation Instructions For Vanity
Customer Service
(USA) 1.800.235.7747
back top rail
STEP 3 | Vanity Installation
1. Fasten the vanity cabinet to the wall with 2 screws (not included) into wall studs through the back top rail or use toggle bolts if necessary.
2. Pulls are attached to the inside of the vanity. Re-attach so the pulls are visible from the outside of the doors.
STEP 2 | Adjustable Height Levelers (Legs) (If Applicable)
Make sure the base of the vanity is leveled by laying a level (not included) across the top. If adjustment is needed use base levelers located under each leg.
* To lower the cabinet turn levelers clock wise or to rise the cabinet turn levelers counter clock wise.
* Adjust until level across the top is leveled.

Summary of content (4 pages)