Datasheet

ManualsBrandsST ManualsDiscrete SemiconductorsTriac, TO-220AB, 600V, 16A

March 2010 Doc ID 7471 Rev 9 1/10

BTA16, BTB16

T1610, T1635

16 A Snubberless™, logic level and standard Triacs

Features

■ Medium current Triac

■ Low thermal resistance with clip bonding

■ Low thermal resistance insulation ceramic for

insulated BTA

■ High commutation (4Q) or very high

commutation (3Q) capability

■ BTA series UL1557 certified (File ref: 81734)

■ RoHS ( 2002/95/EC) compliant

■ Insulated tab (BTA series, rated at 2500 V

RMS

)

Applications

■ Snubberless versions (BTA/BTB...W and

T1635) especially recommended for use on

inductive loads, because of their high

commutation performances

■ On/off or phase angle function in applications

such as static relays, light dimmers and

appliance motor speed controllers

Description

Available either in through-hole or surface-mount

packages, the BTA16, BTB16, T1610 and T1635

Triacs series are suitable for general purpose

mains power AC switching.

TM: Snubberless is a trademark of STMicroelectronics

PAK

T1610G

T1635G

TO-220AB

insulated

BTA16

TO-220AB

BTB16

Table 1. Device summary

Symbol Parameter BTA16

(1)

1. Insulated

BTB16 T1610 T1635

T(RMS)

On-state rms current 16 16 16 16

DRM

RRM

Repetitive peak off-state voltage 600/800 600/800 600/800 600/800

(Snubberless) Triggering gate current 35/50 35/50 - 35

(logic level) Triggering gate current 10 10 10 -

(standard) Triggering gate current 25/50 25/50 - -

www.st.com

Summary of content (10 pages)

PAGE 1
BTA16, BTB16 T1610, T1635 16 A Snubberless™, logic level and standard Triacs Features A2 ■ Medium current Triac ■ Low thermal resistance with clip bonding ■ Low thermal resistance insulation ceramic for insulated BTA ■ High commutation (4Q) or very high commutation (3Q) capability ■ BTA series UL1557 certified (File ref: 81734) ■ RoHS ( 2002/95/EC) compliant ■ Insulated tab (BTA series, rated at 2500 VRMS) G A1 A2 A1 A2 G D2PAK T1610G T1635G A2 Applications ■ ■ Snubberless versions (BT
PAGE 2
Characteristics 1 BTA16, BTB16, T1610, T1635 Characteristics Table 2. Absolute maximum ratings Symbol IT(RMS) ITSM I²t dI/dt VDSM/ VRSM IGM PG(AV) Tstg Tj Table 3. Parameter Value Unit 16 A D2PAK / TO-220AB Tc = 100 °C TO-220AB insulated Tc = 86 °C Non repetitive surge peak on-state current (full cycle, Tj initial = 25 °C) F = 50 Hz t = 20 ms 160 F = 60 Hz t = 16.
PAGE 3
BTA16, BTB16, T1610, T1635 Table 4. Characteristics Electrical characteristics (Tj = 25 °C, unless otherwise specified) standard (4 quadrants) BTA16 / BTB16 Symbol IGT (1) Test conditions VD = 12 V Quadrant RL = 33 Ω VD = VDRM RL = 3.3 kΩ Tj = 125 °C IH (2) IT = 500 mA IL IG = 1.2 IGT 50 100 ALL Max. 1.3 V ALL Min. 0.2 V Max. 25 50 40 60 80 120 Max. II dV/dt (2) VD = 67 %VDRM gate open (2) 25 50 Max.
PAGE 4
Characteristics Figure 1. BTA16, BTB16, T1610, T1635 Maximum power dissipation versus Figure 2. on-state rms current (full cycle) P(W) On-state rms current versus case temperature (full cycle) IT(RMS)(A) 20 18 18 16 16 BTB / T16 14 BTA 14 12 12 10 10 8 8 6 6 4 4 2 2 IT(RMS)(A) TC(°C) 0 0 0 2 Figure 3. 4 6 8 10 12 14 0 16 On-state rms current versus ambient temperature (full cycle) 25 Figure 4.
PAGE 5
BTA16, BTB16, T1610, T1635 Figure 7. Characteristics Non-repetitive surge peak on-state Figure 8. current for a sinusoidal 2 2 Relative variation of gate trigger current IGT,IH,IL[Tj] / IGT,IH,IL[Tj=25°C] ITSM(A), I t (A s) 2.5 3000 holding current and latching current versus junction temperature (typical values) Tj initial=25°C dI/dt limitation: 50A/µs 2.0 IGT 1000 1.5 ITSM IH & IL 1.0 I2t 0.5 2 pulse with width tp < 10 ms and corresponding value of I t 100 0.01 0.10 Figure 9.
PAGE 6
Ordering information 2 BTA16, BTB16, T1610, T1635 Ordering information Figure 12. Ordering information scheme (BTA16 and BTB16 series) BT A 16 - 600 BW RG TRIAC series Insulation A = insulated B = non insulated Current 16 = 16 A Voltage 600 = 600 V 800 = 800 V Sensitivity and type B = 50 mA Standard C = 25 mA Standard SW = 10 mA Logic Level BW = 50 mA Snubberless CW = 35 mA Snubberless Packing mode RG = Tube Figure 13.
PAGE 7
BTA16, BTB16, T1610, T1635 3 Package information Package information ● Epoxy meets UL94, V0 ● Recommended torque value: 0.4 to 0.6 N·m In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. Table 8. D2PAK dimensions Dimensions Ref. Millimeters Min. Typ. Inches Max.
PAGE 8
Package information BTA16, BTB16, T1610, T1635 Table 9. TO-220AB (non-insulated and insulated) dimensions Dimensions Ref. Millimeters Min. A ØI 15.20 a1 C B b2 L A Typ. Max. Inches Min. Typ. 15.90 0.598 3.75 Max. 0.625 0.147 a2 13.00 14.00 0.511 0.551 B 10.00 10.40 0.393 0.409 b1 0.61 0.88 0.024 0.034 b2 1.23 1.32 0.048 0.051 C 4.40 4.60 0.173 0.181 c1 0.49 0.70 0.019 0.027 c2 2.40 2.72 0.094 0.107 e 2.40 2.70 0.094 0.106 F 6.20 6.60 0.244 0.
PAGE 9
BTA16, BTB16, T1610, T1635 4 Ordering information Ordering information Table 10. Ordering information Order code(1) Marking(1) Package Weight Base qty Delivery mode BTA16-xxxyzRG BTA16xxxyz TO-220AB 2.3 g 50 Tube BTB16-xxxyzRG BTB16xxxyz TO-220AB 2.3 g 50 Tube T1610-xxxG-TR T1610xxxG 1000 Tape and reel T1635-xxxG T1635xxxG 50 Tube T1635-xxxG-TR T1635xxxG 1000 Tape and reel D2PAK 1.5 g 1. xxx = voltage, y = sensitivity, z = type 5 Revision history Table 11.
PAGE 10
BTA16, BTB16, T1610, T1635 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.