Datasheet

ManualsBrandsST ManualsDiodesRectifier Diode 12A 1kV TO-220AC

September 2006 Rev 2 1/11

STTH802

Ultrafast recovery diode

Main product characteristics

Features and benefits

■ Very low conduction losses

■ Negligible switching losses

■ Low forward and reverse recovery time

■ High junction temperature

Description

The STTH802 uses ST's new 200 V planar Pt

doping technology, and is specially suited for

switching mode base drive and transistor circuits.

Packaged in TO-220AC, TO-220FPAC, DPAK,

and D

PAK this device is intended for use in low

voltage, high frequency inverters, free wheeling

and polarity protection.

Order codes

F(AV)

8 A

RRM

200 V

j (max)

175° C

(typ) 0.8 V

(typ) 17 ns

Part Number Marking

STTH802D STTH802

STTH802FP STTH802

STTH802B STTH802

STTH802B-TR STTH802

STTH802G STTH802

STTH802G-TR STTH802

TO-220AC

STTH802D

DPAK

STTH802B

TO-220FPAC

STTH802FP

DPAK

STTH802G

www.st.com

Summary of content (11 pages)

PAGE 1
STTH802 Ultrafast recovery diode Main product characteristics IF(AV) 8A VRRM 200 V Tj (max) 175° C VF (typ) 0.
PAGE 2
Characteristics STTH802 1 Characteristics Table 1. Absolute ratings (limiting values at Tj = 25° C, unless otherwise specified) Symbol Parameter Unit VRRM Repetitive peak reverse voltage 200 V IF(RMS) RMS forward current 16 A 8 A 100 A -65 to + 175 °C 175 °C IF(AV) Average TO-220A, DPAK, D2PAK forward current, δ = 0.5 TO-220FPAC IFSM Surge non repetitive tp = 10 ms Sinusoidal forward current Tstg Storage temperature range Tj Table 2.
PAGE 3
STTH802 Characteristics Table 4. Dynamic characteristics Symbol Parameter trr Test conditions Typ Max. Unit IF = 1 A, dIF/dt = -50 A/µs, VR = 30 V, Tj = 25 °C 25 30 ns IF = 1 A, dIF/dt = -100 A/µs, VR = 30 V, Tj = 25 °C 17 22 Reverse recovery current IF = 8 A, dIF/dt = -200 A/µs, VR = 160 V, Tj = 125 °C 5.5 7 Forward recovery time IF = 8 A, dIF/dt = 50 A/µs VFR = 1.1 x VFmax, Tj = 25 °C 150 ns Forward recovery voltage IF = 8 A, dIF/dt = 50 A/µs, Tj = 25 °C 1.
PAGE 4
Characteristics Figure 5. STTH802 Figure 6. Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220FPAC) Zth(j-c)/Rth(j-c) Junction capacitanceversus reverse applied voltage (typical values) C(pF) 1.0 100 Single pulse TO-220FPAC F=1MHz Vosc=30mVRMS Tj=25°C 0.1 VR(V) tp(s) 10 0.0 1.E-03 1.E-02 Figure 7. 1.E-01 1.E+00 1 1.E+01 Reverse recovery charges versus dIF/dt (typical values) 10 1000 Reverse recovery time versus dIF/dt (typical values) Figure 8.
PAGE 5
STTH802 Ordering information scheme Figure 11. Thermal resistance, junction to ambient, versus copper surface under tab - Epoxy printed circuit board FR4, eCU = 35 µm (D2PAK ) Figure 12.
PAGE 6
Package information 3 STTH802 Package information Epoxy meets UL94, V0 Cooling method: by conduction (C) Recommended torque value: 0.8 Nm Maximum torque value: 1.0 Nm Table 5. T0-220AC dimensions DIMENSIONS REF. A H2 ØI C L5 L7 L6 L2 F1 Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 C 1.23 1.32 0.048 0.051 D 2.40 2.72 0.094 0.107 E 0.49 0.70 0.019 0.027 F 0.61 0.88 0.024 0.034 F1 1.14 1.70 0.044 0.066 G 4.95 5.15 0.194 0.202 H2 10.00 10.
PAGE 7
STTH802 Package information Table 6. T0-220FPAC dimensions DIMENSIONS REF A Millimeters Inches Min. Max. Min. Max. A 4.4 4.6 0.173 0.181 B 2.5 2.7 0.098 0.106 D 2.5 2.75 0.098 0.108 E 0.45 0.70 0.018 0.027 F 0.75 1 0.030 0.039 F1 1.15 1.70 0.045 0.067 G 4.95 5.20 0.195 0.205 G1 2.4 2.7 0.094 0.106 H 10 10.4 0.393 0.409 B H Dia L6 L2 L7 L3 L5 F1 D L4 L2 F G1 G E 16 Typ. 0.63 Typ. L3 28.6 30.6 1.126 1.205 L4 9.8 10.6 0.386 0.
PAGE 8
Package information Table 7. STTH802 DPAK dimensions DIMENSIONS REF . E A B2 C2 L2 D R H L4 A1 B R G C A2 Millimeters Inches Min. Max Min. Max. A 2.20 2.40 0.086 0.094 A1 0.90 1.10 0.035 0.043 A2 0.03 0.23 0.001 0.009 B 0.64 0.90 0.025 0.035 B2 5.20 5.40 0.204 0.212 C 0.45 0.60 0.017 0.023 C2 0.48 0.60 0.018 0.023 D 6.00 6.20 0.236 0.244 E 6.40 6.60 0.251 0.259 G 4.40 4.60 0.173 0.181 H 9.35 10.10 0.368 0.397 0.60 MIN. L2 V2 0.
PAGE 9
STTH802 Package information Table 8. D2PAK dimensions Dimensions Ref. A E C2 L2 D L L3 A1 B2 R C B G A2 M * V2 * FLAT ZONE NO LESS THAN 2mm Millimeters Inches Min. Max. Min. Max. A 4.40 4.60 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.70 0.93 0.027 0.037 B2 1.14 1.70 0.045 0.067 C 0.45 0.60 0.017 0.024 C2 1.23 1.36 0.048 0.054 D 8.95 9.35 0.352 0.368 E 10.00 10.40 0.393 0.409 G 4.88 5.28 0.192 0.208 L 15.00 15.
PAGE 10
Ordering information 4 Ordering information Part Number Marking Package Weight Base qty Delivery mode STTH802D STTH802 TO-220AC 1.86 g 50 Tube STTH802FP STTH802 TO-220FPAC 2.2 g 50 Tube STTH802B STTH802 DPAK 0.3 g 75 Tube STTH802B-TR STTH802 DPAK STTH802G STTH802G-TR 5 10/11 STTH802 0.3 g 2500 Tape and reel STTH802 2 D PAK 1.48 g 50 Tube STTH802 D2 1.
PAGE 11
STTH802 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.