Datasheet

ManualsBrandsST ManualsDiscrete SemiconductorsMOSFET, N-Channel, 800V, 10.5A, 190W, TO-247

August 2006 Rev 5 1/16

STB12NK80Z

STP12NK80Z - STW12NK80Z

N-channel 800V - 0.65Ω - 10.5A - TO-220 - D

PAK - TO-247

Zener - Protected SuperMESH™ MOSFET

General features

■ Extremely high dv/dt capability

■ Improved esd capability

■ 100% avalanche tested

■ Gate charge minimized

■ Very low intrinsic capacitances

■ Very good manufacturing repeability

Description

The SuperMESH™ series is obtained through an

extreme optimization of ST’s well established

strip-based PowerMESH™ layout. In addition to

pushing on-resistance significantly down, special

care is taken to ensure a very good dv/dt

capability for the most demanding applications.

Applications

■ Switching application

Internal schematic diagram

Type

DSS

(@Tjmax)

DS(on)

STB12NK80Z 800V <0.75Ω 10.5 A 190W

STP12NK80Z 800V <0.75Ω 10.5 A 190W

STW12NK80Z 800V <0.75Ω 10.5 A 190W

TO-220 TO-247

PAK

www.st.com

Order codes

Part number Marking Package Packaging

STB12NK80Z B12NK80Z

PA K

Tape & reel

STP12NK80Z P12NK80Z TO-220 Tube

STW12NK80Z W12NK80Z TO-247 Tube

Summary of content (16 pages)

PAGE 1
STB12NK80Z STP12NK80Z - STW12NK80Z N-channel 800V - 0.65Ω - 10.5A - TO-220 - D2PAK - TO-247 Zener - Protected SuperMESH™ MOSFET General features Type VDSS RDS(on) (@Tjmax) ID PW STB12NK80Z 800V <0.75Ω 10.5 A 190W STP12NK80Z 800V <0.75Ω 10.5 A 190W 3 1 STW12NK80Z 800V <0.75Ω 10.
PAGE 2
Contents STB12NK80Z - STP12NK80Z - STW12NK80Z Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) ............................ 6 3 Test circuit Package mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . 9 4 Package mechanical data . . . . . . . . . . . . . . . . . . . .
PAGE 3
STB12NK80Z - STP12NK80Z - STW12NK80Z 1 Electrical ratings Electrical ratings Table 1. Absolute maximum ratings Symbol Value Unit Drain-source voltage (VGS = 0) 800 V Drain-gate voltage (RGS = 20KΩ) 800 V Gate-source voltage ± 30 V ID Drain current (continuous) at TC = 25°C 10.5 A ID VDS VDGR VGS Parameter Drain current (continuous) at TC=100°C 6.6 A IDM(1) Drain current (pulsed) 42 A PTOT Total dissipation at TC = 25°C 190 W Derating Factor 1.
PAGE 4
Electrical characteristics 2 STB12NK80Z - STP12NK80Z - STW12NK80Z Electrical characteristics (TCASE=25°C unless otherwise specified) Table 4. Symbol On/off states Parameter Test conditions Drain-source breakdown voltage ID = 1mA, VGS= 0 IDSS Peak diode recovery voltage slope VDS =Max rating, VDS =Max rating, Tc=125°C IGSS Gate body leakage current VGS = ± 20V (VGS = 0) V(BR)DSS Min. Typ. Max. Unit 800 V 1 50 µA µA ±10 µA VGS(th) Gate threshold voltage VDS= VGS, ID = 100µA 3 3.
PAGE 5
STB12NK80Z - STP12NK80Z - STW12NK80Z Table 6. Symbol ISD Source drain diode Parameter Test conditions Source-drain current (pulsed) (2) Forward on voltage ISD=10.5A, VGS=0 Reverse recovery time Reverse recovery charge Reverse recovery current ISD=10.5A, di/dt = 100A/µs, VDD=100V, Tj=150°C trr Qrr IRRM Min Typ. Source-drain current (1) ISDM VSD Electrical characteristics Max Unit 10.5 A 42 A 1.6 V 635 5.9 18.5 ns µC A 1. Pulse width limited by safe operating area 2.
PAGE 6
Electrical characteristics STB12NK80Z - STP12NK80Z - STW12NK80Z 2.1 Electrical characteristics (curves) Figure 1. Safe operating area for TO-220/ D²PAK Figure 2. Thermal impedance for TO-220/ D²PAK Figure 3. Safe operating area for TO-247 Figure 4. Thermal impedance for TO-247 Figure 5. Output characterisics Figure 6.
PAGE 7
STB12NK80Z - STP12NK80Z - STW12NK80Z Electrical characteristics Figure 7. Transconductance Figure 9. Gate charge vs gate-source voltage Figure 10. Capacitance variations Figure 11. Normalized gate threshold voltage vs temperature Figure 8. Static drain-source on resistance Figure 12.
PAGE 8
Electrical characteristics Figure 13. Source-drain diode forward characteristics Figure 15. Maximum avalanche energy vs temperature 8/16 STB12NK80Z - STP12NK80Z - STW12NK80Z Figure 14.
PAGE 9
STB12NK80Z - STP12NK80Z - STW12NK80Z 3 Test circuit Package mechanical data Test circuit Package mechanical data Figure 16. Switching times test circuit for resistive load Figure 17. Gate charge test circuit Figure 18. Test circuit for inductive load Figure 19. Unclamped Inductive load test switching and diode recovery times circuit Figure 20.
PAGE 10
Package mechanical data 4 STB12NK80Z - STP12NK80Z - STW12NK80Z Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a Lead-free second level interconnect . The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark.
PAGE 11
STB12NK80Z - STP12NK80Z - STW12NK80Z Package mechanical data TO-220 MECHANICAL DATA DIM. mm. MIN. TYP inch MAX. MIN. TYP. MAX. A 4.40 4.60 0.173 0.181 b 0.61 0.88 0.024 0.034 b1 1.15 1.70 0.045 0.066 c 0.49 0.70 0.019 0.027 D 15.25 15.75 0.60 0.620 E 10 10.40 0.393 0.409 e 2.40 2.70 0.094 0.106 e1 4.95 5.15 0.194 0.202 F 1.23 1.32 0.048 0.052 H1 6.20 6.60 0.244 0.256 J1 2.40 2.72 0.094 0.107 0.551 L 13 14 0.511 L1 3.50 3.93 0.
PAGE 12
Package mechanical data STB12NK80Z - STP12NK80Z - STW12NK80Z TO-247 MECHANICAL DATA DIM. mm. MIN. inch MAX. MIN. TYP. MAX. A 4.85 5.15 0.19 0.20 A1 2.20 2.60 0.086 0.102 b 1.0 1.40 0.039 0.055 b1 2.0 2.40 0.079 0.094 0.134 b2 3.0 3.40 0.118 c 0.40 0.80 0.015 0.03 D 19.85 20.15 0.781 0.793 E 15.45 15.75 0.608 0.620 e 5.45 0.214 L 14.20 14.80 0.560 L1 3.70 4.30 0.14 L2 18.50 0.582 0.17 0.728 øP 3.55 3.65 0.140 0.143 øR 4.50 5.50 0.177 0.
PAGE 13
STB12NK80Z - STP12NK80Z - STW12NK80Z Package mechanical data D2PAK MECHANICAL DATA TO-247 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. MIN. TYP. MAX. A 4.4 4.6 0.173 0.181 A1 2.49 2.69 0.098 0.106 A2 0.03 0.23 0.001 0.009 B 0.7 0.93 0.027 0.036 B2 1.14 1.7 0.044 0.067 C 0.45 0.6 0.017 0.023 C2 1.23 1.36 0.048 0.053 D 8.95 9.35 0.352 0.368 10.4 0.393 D1 E 8 10 E1 0.315 8.5 0.334 G 4.88 5.28 0.192 0.208 L 15 15.85 0.590 0.625 L2 1.27 1.4 0.
PAGE 14
Packing mechanical data 5 STB12NK80Z - STP12NK80Z - STW12NK80Z Packing mechanical data D2PAK FOOTPRINT TAPE AND REEL SHIPMENT REEL MECHANICAL DATA DIM. mm MIN. A B 1.5 C 12.8 D 20.2 G 24.4 N 100 T TAPE MECHANICAL DATA DIM. mm MIN. MAX. MIN. A0 10.5 10.7 0.413 0.421 B0 15.7 15.9 0.618 0.626 D 1.5 1.6 0.059 0.063 D1 1.59 1.61 0.062 0.063 E 1.65 1.85 0.065 0.073 F 11.4 11.6 0.449 0.456 MAX. K0 4.8 5.0 0.189 0.197 P0 3.9 4.1 0.153 0.161 P1 11.9 12.1 0.
PAGE 15
STB12NK80Z - STP12NK80Z - STW12NK80Z 6 Revision history Revision history Table 8.
PAGE 16
STB12NK80Z - STP12NK80Z - STW12NK80Z Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale.