STABER CLOTHES WASHER HXW2304 HXW2305 HXW2404 HXW2405 HXW2504 HXW2505 Operator’s Manual Installation/Operation/Maintenance/Parts Part Number 818235 Printed in USA
FORWARD We are pleased that you have selected a Staber clothes washer as one of your appliances. Your clothes will be washed using a tumble action inner tub. Please register your new Staber washer on our Internet web site, www.staber.com. An average of sixteen gallons of water per cycle moves through your clothes to clean them, therefore less water and detergent is used than in agitator washers.
PRODUCT IDENTIFICATION Model, Series and Serial numbers are used to identify your new Staber clothes washer. These numbers should always be referred to when consulting the Customer Assistance Center concerning service, parts, or other information you may require. For your convenience and ready reference, enter Model, Series, and Serial numbers below. Model number. Series number. Serial number. IMPORTANT SAFETY INSTRUCTIONS This safety alert symbol means CAUTION or WARNING – “personal safety instruction.
IMPORTANT GROUNDING INSTRUCTIONS This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances .
INSTALLATION CAUTION: Use great care when loading, unloading or working around clothes basket with top lid raised. DO NOT allow any items to fall between inner and outer tubs. If this should occur DO NOT START WASHER. The item must be removed from the tub or damage to the clothes basket or water system may occur. If the item cannot be removed by rotating the clothes basket, we recommend removing the item though the sump hose. Refer to maintenance procedures for details.
BENEFITS OF STABER WASHER 1 Washes more clothes per load than a traditional agitator washer and saves on drying time with superior moisture extraction. 2. Gentle wash action ensures less wear and tear on clothes (clothes last longer). 3. Conserves water, energy, and money spent on laundry products. TO WASH CLOTHES, FOLLOW THESE SIMPLE INSTRUCTIONS STEP 1 After raising top outer lid, open access doors to clothes basket.
STEP 1 STEP 2 STEP 3 STEP 4 STEP 5 CAUTION FOUR THINGS THAT AFFECT THE CLEANLINESS OF YOUR CLOTHES 1. The amount of Agitation: Equipped with a patented inner and outer tub, the Staber washer is designed to increase the agitation rate allowing for minimal use of chemicals, heat and time per wash load. 2. The amount of Detergent used: The increased agitation performance eliminates the need for excess detergent, leaving your clothes smelling less like perfume and more like natural woven fabrics.
OPERATION CONTROLS Temperature Controls temperature of wash water only. Clothes washer is designed to use cold water for rinses. Water level Controls amount of water entering clothes washer during each fill. Use High setting for all normal loads containing a fully or loosely packed tub. Use Low setting for loads containing only a few garments. Wash cycle Controls agitation speed, agitation duty cycle and spin speed. Use Normal setting for most fabrics; it has the fastest spin speed.
MAINTENANCE PROCEDURES REMOVE FRONT PANEL 1 Disconnect the appliance from the power source. 2 Remove the four 5/16 headed screws located at the bottom of the front panel. 3 After the screws have been removed, grasp the panel on both sides and pull forward. Allow the panel to drop free of the top assembly and set aside. INSTALL FRONT PANEL 1 Locate left and right side of front panel over guide pins on cabinet.
REPLACE DRIVE BELT 1 Remove the front panel as directed under "REMOVE FRONT PANEL". 2 Remove belt and inspect pulleys for wear and tightness. 3 Install new belt on pulleys, check belt tension and adjust as necessary. Install front panel on clothes washer as directed under "INSTALL FRONT PANEL" and plug power cord into electrical receptacle. REPLACE PUMP 1 Remove the front panel as directed under "REMOVE FRONT PANEL".
14 Reinstall control panel to housing. Insert bottom of control panel into housing first. Then slide the panel into place and secure with six philips head screws. NOTE: Do not over tighten the screws or you will strip the holes and the screws will not hold. 15 Plug machine into the 120 vac power supply. REPLACE TEMPERATURE, WATER LEVEL AND WASH CYCLE SWITCHES 1 Disconnect the appliance from the power source. 2 Remove the six screws that hold the control panel to the top.
REPLACE PRESSURE SWITCH 1 Disconnect the appliance from the power source. 2 Remove the six philips head screws that hold the control panel to the top. 3 Allow the control panel to slide down, pull the top of the control panel out and lift up. 4 Lay the control panel face down on the top. 5 Pull up on the pressure switch that is fastened to the bottom of the control housing. 6 Remove the connectors from the switch. 7 To install a new switch, reverse the above procedures.
TROUBLESHOOTING PROBLEM CAUSE CORRECTIVE ACTION Power On light does not illuminate when Clothes washer not plugged in. Plug power cord into properly grounded timer knob is pulled out. 13 receptacle. Electrical outlet does not have AC power. Check fuse or circuit breaker. Light is burned out. Replace light. Lid locked light does not illuminate during Lid is not fully closed. Close lid completely. spin cycle. Microprocessor did not properly boot up.
TROUBLESHOOTING PROBLEM CAUSE CORRECTIVE ACTION Water does not drain from clothes washer. Obstruction in sump area of outer tub. Remove obstruction. Obstruction in sump hose. Remove obstruction. Obstruction in pump. Remove pump and clear obstruction. Obstruction in drain hose or stand pipe. Remove obstruction. Pump has failed. Replace pump. Stand pipe higher than seven feet. Shorten stand pipe. Poor connection on timer plug. Reseat connector. Motor control circuit has failed.
PARTS ITEM 75 PART NUMBER 813271M DESCRIPTION Wiring Harness QUANTITY 1 76 77 78 79 813226 813203 814201 814237 Motor Controller Lid Lock Pump Water Valve 1 1 1 1 80 81 82 83 84 813215 813209 813223 813211 813267 Pressure Switch Switch - Temperature Switch - Water Level Switch - Program Selector (Wash Cycle) Timer 85 813213 813214 813245 Indicator Light - Red Indicator Light - Green Circuit Breaker 10 AMP 1 1 1 1 1 1 1 1 1 86 15
PARTS ITEM 1 2 3 4 5 PART NUMBER 813217 818225 818265 818229 817216 DESCRIPTION Motor Flat Washer 5/16 Lock Washer 5/16 Bolt 5/16-18 x 3/4 Shaft, Motor Pivot QUANTITY 1 1 1 1 1 6 7 8 9 10 817222 818219 817219 817305 818261 Spacer Retaining Ring Weight - Side Bracket Bolt 5/16-18 x 4 2 2 2 2 4 11 12 13 14 15 818225 818265 818263 817220 817217 Flat Washer 5/16 Lock Washer 5/16 Nut 5/16-18 Motor Pivot Shaft Bushing Weight - Rear 4 4 4 1 1 16 17 18 19 20 817307 818225 818265 818263 817101 Brac
PARTS 17
PARTS ITEM 44 45 46 47 48 PART NUMBER 817271 817115 818217 817291 817289 DESCRIPTION Cabinet Front Panel Screw Locking Pin Lid QUANTITY 1 1 4 1 1 49 50 51 52 53 817103 817107 818201 817109 813221 Inner Tub Assembly Drive Shaft Assembly Bolt 1/4-20 x 5/8 S.S.
PARTS 19
Staber Industries, Inc. 4800 Homer Ohio Lane Groveport, Ohio 43125 614.548.0098 phone www.staber.com Product information and specifications are shown herein as of the time of printing. Staber Industries, Inc. reserves the right to change product specifications, designs and standard equipment without notice and without incurring obligation.
