User manual

Control elements and connections
Camera
Control elements and connections
Monitor
Antenna
For an optimum reception, the antenna must be as vertical as possible.
Power/Screen key
Power key: For switching the monitor on or off, press and hold the key for
three seconds.
Screen key: For switching the power saving mode on or off, press and hold
the key for three seconds.
Foldable monitor stand
For positioning the monitor.
TF card
Micro SD card (max. 32 GB) for data backup of recordings saved on the
hard disk.
USB port
Port for connecting an USB mouse for menu operation.
HDMI port
TV port.
LAN port
Internet connection (RJ45) for LAN cable.
DC IN socket
for power supply unit OUTPUT 12 V DC/2A.
Power LED
is lit red, when the monitor is switched on
Important
Prior to using the device for the first time, carefully and completely read
through all operating instructions.
stabo is eco-friendly.
To help us save trees and reduce paper waste, you will find all operating
instructions with care and safety instructions as well as warranty informations
online at
http://stabo.de/fileadmin/BdA/BdA_stabo_smart_i_control_DE_EN.pdf
Quickstart manual
digital radio technology 2.4 GHz
smart i
_
control
Video-Überwachungssystem
Art. No. 51092
Figure shows monitor
in quad setting
which is only possible
when using additional cameras
22,9 cm
Touchscreen
Scope of delivery
22,9 cm (9) color LCD Touchscreen monitor with photo frame bracket
WLAN wireless color camera (IP 66)
with mounting bracket (ceiling/wall fastening)
power supply for monitor 12 V/2 A, power supply for camera 5 V/2 A
RJ45 network cable
quickstart user manual DE/EN
Please check the contents of the package for completeness.
Prior to using the device, examine it with respect to any external damage.
In case of an external damage, do not put the product into operation, but
contact your specialist dealer immediately.
3
Antenna
Power/Screen key
Control elements
and connections
Monitor
Power LED
TF card
USB port
LAN port
HDMI port
DC IN socket
Foldable monitor stand
5
Control elements and connections
Camera
Antenna
For an optimum reception, the antenna must be as vertical as possible.
Power LED
After switching on, the power LED lights red for about 3 seconds. When
the connection to the monitor is established, the power LED lights blue.
Note: After approx. 10 minutes, the power LED will be deactivated.
Infrared LEDs
24 high-performance infrared LEDs (visibility of 20 - 30 m under ideal
conditions)
Light sensor
The night vision function is automatically activated/deactivated through the
light sensor.
Camera mount
Camera mount for fixing the camera on the wall or ceiling.
Pairing key
For connecting additional cameras to the monitor.
DC IN socket
Connecting cable for power supply unit OUTPUT: 5 V DC / 2 A.
Pairing key
Camera mount
Power LED
Light sensor
DC IN socket
Infrared LEDs
Antenna
7 8
4
6
2
Hard disk installation
Note: You need a HDD 2.5 SATA hard disk (max. capacity 2 TB)
Undo both screws from the cover
of the hard disk compartment and
remove the cover.
Position the hard disk at an angle
(connections facing to the front
side) in front of the hard disk slot.
Now push the hard disk inwards
and downwards for inserting the
connector strip (1) into the slot
(2).
Afterwards reinstall the cover and use the two screws for fixing the cover.
Note: Before first using it, the hard disk must be formatted in the monitor
(using the function HDD Format under menu item Record Setting).
Attention: Due to formatting, all previously saved data will be irretrievably
lost
12
Mounting and installation of monitor and camera
Important note: First, install the monitor and camera only provisionally
and check whether a reliable radio transmission is assured on the
planned place of action.
Monitor
If you wish to use the system with the help of the app Kalay Cam,
the monitor must first be connected to your local home network using
the LAN cable included in the scope of delivery.
Important note: DHCP should be deactivated.
Place the monitor on a flat surface such that tilting is prevented and
adjust it depending on the angle of view.
For positioning the monitor, unfold the foldable monitor stand at the
back side of the monitor.
Screw the antenna on the antenna jack.
Plug the power supply unit into a socket (230 V) and connect the plug
to the 12 V DC IN socket on the side of the monitor.
For switching the monitor on, press and hold the ON/OFF button on
its top side for 3 seconds. The power-on indicator lights up red.
The monitor now briefly shows the stabo logo and afterwards switches
over to the live image (if the camera is switched on). If the camera is
not switched on, the screen remains dark.
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, stabo Elektronik GmbH declares that the radio equipment type
stabo smart i_control
is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available
at the following internet address:
http://stabo.de/fileadmin/DoC/DoC_stabo_smart_i_control_DE_EN.pdf