User manual

9 10 11 12
After having finished the installation, the monitor/NVR with the UUID
number appears in the device list and the online status of the device
is shown.
For activating the live image, tap the film
strip symbol on the left.
Afterwards the live image is shown on the
display.
1413
Errors and technical modification reserved. Pictures may vary.
Copyright © 11/2017 stabo Elektronik GmbH
stabo Elektronik GmbH
.
Münchewiese 16
.
31137 Hildesheim/Germany
Tel. [phone]
.
Fax: [phone]
Internet: www.stabo.de
.
E-Mail: [e-mail]
Technical Data
Monitor
Screen type 22,9 cm (9) TFT LCD touchscreen
Image resolution TFT- LCD 1024(H) x 600(V)
Display resolution max. 720p
Video compression H.264
Video input mode 4x 720p (4x camera)
Recording frame rate max. 25fps/30fps @ 720p pro channel
Connections 1x HDMI(1.3), 1x USB(2.0), 1x RJ45, DC IN socket
HDD slot max. 2 TB
mikroSD card slot max. 32 GB
Operating voltage DC 12 V / 2 A
Working temperature range -10° ~ 55°
Working humidity range 10 - 90%
Dimensions (H x W x D) 243,8 x 163,5 x 30,3 mm
Weight 680 g
Camera
Image sensor ¼ 1 megapixel CMOS sensor
Objektiv 3,6 mm
Video Qualität 720p (1280x720)
Angle of view (diagonal) 70° diagonal
IR LEDs 24, wavelength 850 nm
Night vision distance ca. 20-30 m
Protection class IP 66
Operating voltage DC 5 V / 2 A
Working temperature range -10° ~ 60°
Working humidity range < 95%
Dimensions Ø 67,5 mm, H 164 mm
H 90 mm (
without support)
Weight 360 g (with support)
Bedienungsanleitung
User Manual
stabo smart i_control
Camera
Important information: Consider the following when selecting the
camera position:
Range: The best range is achieved with a free line of sight between
camera and monitor. Walls made of steel and concrete lead to a
reduction in range.
Lighting conditions: The camera should not be orientated towards
direct, strong light sources/sunlight, since overexposed images may
result.
Power supply: The camera's power supply unit must not be exposed
to the weather in the open! The plug-in connection of the power supply
cable must be protected for preventing any moisture from entering.
Mounting
Protection type IP 66 allows devices to be installed in the open. However,
the camera should nevertheless be installed in a well protected place.
Make sure that the mounting surface is stable and does not give rise
to strong vibrations and/or falls.
First, install the camera only provisionally and check whether the
desired monitored area is completely covered and a reliable radio
transmission is assured at the intended mounting position. Prior to
drilling the holes for the camera support, check and optimize the
arrangement of the system! Make sure that no cables or conducts are
placed in the wall which may be damaged when drilling!
Mark the desired position for the three drilling holes of the fixing screws
by using the holes in the camera mount as drilling jig.
Drill the three mounting holes and fix the camera using screws which
are suitable for the respective base material.
Screw the antenna on the antenna jack.
Carefully, align camera and antenna.
Plug the power supply unit into a socket (230 V) and connect the plug
to the DC IN socket of the camera.
Establishing the connection between monitor and camera
Camera and monitor are already coupled ex works.* As soon as monitor
and camera are switched on, the monitor display shows the image
taken.
*Note: However, each additional camera (available as option) must
be individually coupled to the monitor.
Installing the app Kalay Cam
The smart i_control video monitoring system permits remote access
through the Internet with the help of an app for mobile devices. The
app is available for use with Android and iOS operating systems.
For the free-of-charge app Kalay CAM for Android and iOS devices
please refer to Google Play and the app store or use the following QR
codes:
After installation tap the Kalay CAM symbol for
activating the app.
The welcome screen is shown.
Note: Make sure that
l the network cable included in the sco-
pe of delivery is used for connecting
the monitor to your router,
l the Online box of your monitors net-
work status in the menu Network set-
tings is checked.
Note: Normally, no settings are required,
since the monitor/NVR automatically
received the IP address (DHCP is
preset), if a DHCP server is available
in your network (in general integrated
in each router).
Now scan the QR code (contains the UUID
number) on the back side of the monitor.
Assign a password and a camera name and
tap the check symbol afterwards.
Note: Make a note of your password.
Note: The standard password is 888888, the standard name is Kamera
Adding the monitor/NVR
Tap Camera on the welcome screen.
For adding a monitor/NVR now tap the +
sign.
Note: A maximum of 4 monitors/NVRs can
be added.
Android iOS