Use and Care Guide

ManualsBrandsSTAINMASTER ManualsVinyl TileLSS3131EPS

PEEL & STICK LUXURY VINYL TILE

PREPARARATION:

1. Why is acclimation necessary for my floor tiles and how long? Acclimation allows the solid vinyl flooring to become equal to

the installed environment. This will better allow the flooring to become more stable during normal temperature fluctuations.

All floors must be acclimated under normal site conditions and temperatures for 48 hours prior to installation. Ideal room

temperatures for luxury vinyl should be maintained at 65°F-85°F (19°C-29°C).

2. What subfloors are approved for peel & stick tiles and planks? Approved subfloors are

• Concrete

• Underlayment grade plywood

• Exterior grade plywood (sanded face, B-C or better grade)

• Properly prepared non-cushion backed vinyl flooring

• All subfloors must be clean, dry and free of contaminants such as oil, grease, paint, sealers, waxes, curing compounds,

excessive moisture, hydrostatic pressure.

• Floors must be structurally sound, rigid and flat to 3/16” in 10 feet (F-32).

3. Why not OSB, Luan or other subfloors? OSB, Luan, particle board, Masonite and other non-underlayment grade plywood are

generally not smooth and not constructed with exterior rated adhesives, making them susceptible to moisture related failures.

Additionally, these types of substrates may have a coating which is not compatible with floor adhesives (including peel and

stick adhesives) and will prevent a proper bond.

4. What if I go over existing vinyl / sheet vinyl / linoleum? Existing sheet goods are permitted provided they are non-cushioned

back, single layer floors. Sheet goods must be properly prepared with a suitable cementitious embossing leveler; following the

embossing leveler’s manufacturer directions regarding preparation of the surface and mixing with the appropriate additive.

5. What if the existing vinyl floor has texture? Use a cementitious embossing leveler to skim the surface of the textured floor.

Follow the embossing leveler’s manufacturer directions regarding preparation of the surface and mixing with the appropriate

additive.

6. Is a Primer necessary for peel and stick installation? No, primers are not necessary on the recommended subfloors in our

Installation Guides. If you want to use a primer, it MUST be a latex based specifically made for VINYL FLOORING.

7. How do I make some corners and edge stick back down that are lifting? Gently heat the area of the tile with a heat gun or a

common hair dryer on low setting. When the tile becomes pliable, simply press it back into place and then place some weights

on it overnight.

8. Can I install over a heated floor? Stainmasterâ luxury vinyl floors can be installed over radiant heated floors provided the

floor is NOT allowed to be heated of 85°F (29°C), or cooled below 55°F (13°C).

INSTALLATION:

1. What are the arrows on the back of the release paper for? Directional arrows are for keeping the finish looking consistent

throughout the installation. Also used when laying tiles in a quarter-turned method giving a more random look.

2. Can I use “extra” adhesive with my peel and stick installation tiles? NO! Common latex-based flooring adhesives are not

compatible with Stainmasterâ peel and stick tiles. Use of a secondary adhesive may cause a plasticizer migration and will

cause an adhesive failure.

3. What type of tools do I need for installation? Commonly used tools for vinyl tile installation are; a utility knife with heavy duty

blades, 100lb 3 section roller, chalk line, measuring tape, broom, pencil, heat gun, speed square, wide putty knife, small trim

pull bar.

4. How much space is needed for expansion? Peel and stick luxury vinyl requires 1/8” expansion gap at all vertical surfaces it

meets.

5. Is a 100lb roller required and where can I get one? YES! Proper rolling with a 100lb 3 section roller will ensure proper pressure

is applied to the flooring for adhesives to bond to the substrate. Most equipment rental stores have these to rent by the day.

6. Where to start; from the center or from the corner of the room? Plank installations usually start from the upper, left corner

of the room while tile installations are started from the center point of the room.

7. How do cut round shapes or special cuts? Use a compass or or create a template with a piece of cardboard for special cuts

and draw your shape. Then carefully heat the tile with the heat gun or hair dryer on the lowest setting. When the tile is warm

and pliable, carefully use a utility knife with a sharp blade to cut the shape. Multiple passes will be best.

FREQUENTLY ASKED QUESTIONS

Summary of content (3 pages)

PAGE 1
FREQUENTLY ASKED QUESTIONS PEEL & STICK LUXURY VINYL TILE PREPARARATION: 1. Why is acclimation necessary for my floor tiles and how long? Acclimation allows the solid vinyl flooring to become equal to the installed environment. This will better allow the flooring to become more stable during normal temperature fluctuations. All floors must be acclimated under normal site conditions and temperatures for 48 hours prior to installation.
PAGE 2
8. 9. How do I remove adhesive from the joints and tops of the tiles? On peel and stick tiles, you will need to use mineral spirits. Using a soft, white cloth, apply mineral spirits sparingly to the cloth first. Then gently dab the area on the tile with the cloth to pull the adhesive up. Do not pour the mineral spirits on the tile or use the cloth in a rubbing motion as this may damage the finish of the tile or lead to an adhesive failure.
PAGE 3
Claim Process: How do I file a claim? While Novalis strives to manufacture the highest quality of of luxury vinyl flooring available today, we realize there may be an occasion for a customer to file a claim. Please follow the following steps below to contact us regarding any issues you may have with your Stainmasterâ luxury vinyl floor. 1. 2. 3. 4. 5. 6. 7.