Manual

ManualsBrandsStairville ManualsDMX Lighting Control DesksDMX Invader 2420 MK II

Owner‘s Manual

DMX Controller

Invader 2420

Please carefully read this manual!

Summary of content (56 pages)

PAGE 1
Invader 2420 Owner‘s Manual DMX Controller Please carefully read this manual!
PAGE 2
Content Notes on safety...................................................................................................................................................................3 Maintenance and care........................................................................................................................................................3 Introduction..........................................................................................................................................
PAGE 3
Notes on safety For your own safety you should read through this chapter at first completely! Risk of electrical shocks! XXOnly connect the device to a properly wired and earthed mains power socket with mains voltage of 230 V ~ /50 Hz. XXDo not operate the device if the power cord or the mains plug are damaged. XXNever submerse the device in water. Wipe it with a slightly moistened cloth only. XXDo not expose the device to rain and never use it in a damp or wet environment.
PAGE 4
Introduction Thank you for purchasing our Invader 2420. Enjoy your new equipment and make sure to read this manual carefully before operation! Features XX 2 x DMX Outputs XX 484 DMX Channels in total, including 481Ch. for DMX fog, 482Ch. for future use, 483-484Ch. for DMX strobe XX Fixture Library ( for built-in ACME lighting fixtures; Other brand fixtures can be set manually but Max.
PAGE 5
General instructions Please read the user manual carefully, as it includes important information regarding details of operation, maintenance, and technical data. Keep this manual with the unit for future consult. WARNINGS XXDO NOT make any inflammable liquids, water or metal objects enter the unit. XXShould any liquid be spilled on the unit, DISCONNECT the power supply to the unit immediately.
PAGE 6
1. Fog Machine Button Activates Fog Machine. 2. STROBE Button Trigger strobe. 3. Fixture Group Button Select /set one or more fixtures group 4. Fixture Button Select one or more fixtures 5. Preset Button Select/set the colour & gobo preset. 6. Movement Button Select/set the pan & tilt movement 7. Chase Button Run Chase and save Scene to Chase 8. Cue Button Save several Chases together and make them run at the same time 9.
PAGE 7
Fixture number channel list Fixtures number buttons Fixture DMX channels Fixtures number buttons Fixture DMX channels 1 2 3 4 5 6 7 8 9 10 1-24 25-48 49-72 73-96 97-120 121-144 145-168 169-192 193-216 217-240 11 12 13 14 15 16 17 18 19 20 241-264 265-288 289-312 313-336 337-360 361-384 385-408 409-432 432-456 457-480 23. ESC/CLEAR Button Back to last menu/delete all the output when program 24. Enter/main menu Button Confirm or enter next menu or enter main menu 25.
PAGE 8
Operation guide (Operating steps instructions) When power is turned on, the controller starts self testing automatically, the LCD Display indicating the self testing progress. After it is finished, the fixture pilot on the rear board is on, which means that you can start to operate the controller. 1. Setting menu Entering the menu 1. Enter Program mode. 2. Press ENTER/MAIN MENU Button to enter LCD screen main menu.
PAGE 9
1.1 Create a new fixture profile 1. Enter Menu Mode. 2. Turn jog wheel #1 up to when the 01.Create a new Fixture is shown on the monitor, press ENTER/MAIN MENU Button to enter. 3. Use Jog wheel #2 and #4 to change the name of the FIXTURE. Turn Jog wheel #2 to change the position of the cursor, and Jog wheel #4 should be used to change the trait of the channel or character.
PAGE 10
. Back to the last menu please press ESC/CLEAR button. 1.2 Modify a fixture profile 1. Enter Menu Mode. 2. Turn jog wheel #1 up to when the 02.Modif a Fixture is shown on the monitor, press ENTER/MAIN MENU Button to enter. 3. Use Jog wheel #3 to chose the bank of other manufacturers, and Jog wheel #4 to chose the ACME’s. 4. Press ENTER/MAIN MENU button to enter. 5. Use Jog wheel #2 and #4 to change the name of the FIXTURE.
PAGE 11
8. Repeat 3-7 to change other FIXTURE PROFILE. 9. Back to the last menu please press ESC/CLEAR button. 1.3 Delete a fixture profile 1. Enter Menu Mode. 2. Turn jog wheel #1 up to when the 03.Delete a Fixture is shown on the monitor. Then press ENTER/MAIN MENU button to enter. 3. Use Jog wheel #3 to delete the profile of other manufacturers, and Jog wheel #4 to delete the ACME’s. 4. Press ENTER/MAIN MENU Button to enter and LCD will show “NO”. 5. Turn Jog wheel #1 to chose “Yes”. 6.
PAGE 12
1.4 Patch a fixture 1. Enter Menu Mode. 2. Turn Jog wheel #1 up to when the 04. Patch a Fixture is shown on the monitor Press ENTER/MAIN MENU Button to enter. 3. Press number Button 1-20 to chose the fixture which needs to patch. 4. Turn Jog wheel #3 to chose the profile of other manufacturers and Jog wheel #4 to chose ACME’s. 5. Press ENTER/MAIN MENU Button to enter, all the LEDs strobe for 3 times. 6. Repeat 3-5 to patch all the fixtures. 7. Back to the last menu please press ESC/CLEAR button. 1.
PAGE 13
4. Turn Jog wheel #2 to change the position of the cursor, and Jog wheel #4 used to reverse the channel. 5. Turn Jog wheel #3 to chose the channel, Jog wheel #4 to reverse. 6. Press ENTER/MAIN MENU Button to enter, all the LEDs will blink for 3 times. 7. Repeat 3-6 to reverse other channels. 8. Back to the last menu please press ESC/CLEAR button. 1.6 Fade mode setup 1. Enter Menu Mode. 2. Turn Jog wheel #1 up to when the 06. Fade mode setup is shown on the monitor, press ENTER/MAIN MENU button to enter.
PAGE 14
1.7 Blackout mode select 1. Enter Menu Mode. 2. Turn Jog wheel #1 up to when the 07. Blackout mode select is shown on the monitor press ENTER/MAIN MENU button to enter. 3. Turn Jog wheel #2 to chose Stand by or Pan/tilt centre or Blackout scene. 4. Press ENTER/MAIN MENU Button to enter, all the LEDs will blink for 3 times, then back to the last menu. 1.8 Midi channel select 1. Enter Menu Mode. 2. Use Jog wheel #1 up to when the 08.
PAGE 15
1.9 Chase run by inside/outside time 1. Enter Menu Mode. 2. Turn jog wheel #1 up to when the 09.Chase run by inside/outside time is shown on the monitor, Press ENTER/MAINMENU Button to enter 3. Use Jog wheel #2 to chose Chase run by inside time or Chase run by outside time 4. Press ENTER/MAIN MENU Button to enter, all the LEDs will blink for 3 times, then back to the last menu. 1.
PAGE 16
5. After 3 seconds, use jog wheel #2 to select the fixtures of the first group, and jog wheel #4 to select the fixtures of the second group. When you turn the jog wheel #2 or #4, the cursor will switch between the first and second group. The fixtures of this two group will be selected in turn, and the unit will act differently when it be selected. 6.
PAGE 17
5. Use Jog wheel #2 to select Yes/no. 6. Press ENTER/MAIN MENU Button to enter. 7. After read up the file, the LCD will hint to complete. Repeat 3-7 to read up other files. 8. Back to the last menu, please press ESC/CLEAR Button. 9. Press ESC/CLEAR Button 2 times to back to the main menu or 3 times to exit the menu. NOTE: Please backup the programs before you load program file, or the program file you load will replace all the program in the controller.
PAGE 18
5. Select Yes, then LCD will hint to input file name. Use Jog wheel #4 to select the file name and move the cursor, you can input as munch as 8 characters. 6. Press ENTER/MAIN MENU Button to store, it will be finish after about 2 minutes. 7. Press ESC/CLEAR Button to back to the last menu, 2 times to back to the main menu. 1.13 Modify password 1. Enter Menu Mode. 2. Turn Jog wheel #1 up to when the 13. Modify Passwords shown on the monitor. Press ENTER/MAIN MENU button to enter. 3.
PAGE 19
1.14 Enable password 1. Enter Menu Mode. 2. Turn Jog wheel #1 up to when the 14. Enable password shown on the monitor. Press ENTER/MAINMENU button to enter. 3. Use Jog wheel #1 to select use power password or use memory protect password, press ENTER/MAIN MENU button to enter. 4. The LCD hint to input password, use number button 1-10 to input 6 digit password. 5. Use Jog wheel #2 to select Enable or Disable. 6.
PAGE 20
3. The LCD hint to input 6 digit memory protect password. Input the exact password, and Press ENTER/MAIN MENU Button to delete the memory information. You have to input the password again when it’s wrong. 4. Use Jog wheel #2 to select Yes (delete and back to the last menu) or No (back to the last menu). 1.16 Audio input range adjust 1. Enter Menu Mode. 2. Turn Jog wheel #1 up to when 16. Audio input range adjust shown on the monitor. Press ENTER/MAIN MENU Button top enter. 3.
PAGE 21
4. Press ENTER/MAIN MENU Button to store and back to the main menu back to the main menu without any change. Press ESC/CLEAR Button. 2 Programming mode Press PROGRAM button for 3 seconds, the LED above this button lights blinking indicating Program in active. 2.1 Setting a scene 1. Enter Program mode. 2. Press the button 1-20 to select Fixture, you can select several fixtures at a time by tapping of these buttons. 3.
PAGE 22
7. Repeat steps 2-6 to program other scenes. 8. Press PROGRAM button for 3 seconds to exit Program mode, the LED goes out indicating this selection. 2.2 Program a scene with movement 1. Enter Program mode. 2. Press the button 1-20 to select Fixture, you can select several fixtures at a time by tapping of these buttons. 3. Move Faders 1-24 or use the CENTRE, PRESET, SCENE have saved to change the output of each channel, press MOVEMENT button. 4.
PAGE 23
11. If you don‘t intend to continue your programming, press and hold down the PROGRAM button for three seconds to exit Program mode, the LED goes out indicating this selection. 2.3 Program a scene 1. Enter Program mode. 2. Press the button BANK, to turn on its fader control, which is indicated by the lit LED, use Jog wheel #1 to select the bank number to edit the scene. 3. Press the number button 1-20 to open the scene you are going to edit. 4.
PAGE 24
8. Press the button PROGRAM for three second, to exit Program mode, the LED goes out indicating this selection. Hint: If you select different scenes at step 3 and 6, the editing scene would cover the scene at step 6. 2.4 Copy a scene 1. Enter Program mode. 2. Press the button BANK, to turn on its fader control, which is indicated by the lit LED. Use Jog wheel #1 to select the bank number to edit the scene. 3. Press the number button 1-20 to open the scene you are going to copy. 4.
PAGE 25
2.5 Delete a scene 1. Enter Program mode. 2. Use the Jog wheel #1 to select the Bank number of the being deleted scene. 3. Press the number button 1-20 to select the scene you are going to delete. 4. Press the button AUTO/DEL. 5. Press the button BANK. 6. Then press the number button 1-20, the scene will be deleted, all LEDs and the Segment Display will blink for three times briefly indicating this operation, then the LCD will show the bank and the scene number of the deleted scene. 7.
PAGE 26
3. Use the Jog wheel #1 to select the Bank number of the being copied scene. 4. Press the button MANUAL/REC, LEDs on CUE, OVERRIDE, CENTRE, FIXTURE GROUP, PRESET, CHASE, BANK, BLACKOUT blink at the same time. 5. Then turn the Jog wheel #1 to select the bank number to copy to. 6.
PAGE 27
4. Use the Jog wheel #1 to transfer to other Banks, then press the number button 1-20 to select the scene to store the Chase. 5. Use the Jog wheel #3 to adjust the FADE TIME of present chase, the Jog wheel #4 to adjust the WAIT TIME of the present chase. If you do not make any adjustments, the system will remember the last FADE TIME or WAIT TIME. 6. Press the button MANUAL/REC, all the LEDs will blink for three times briefly indicating the store succeed. 7.
PAGE 28
5. Use the Jog wheel #3, #4 to adjust the FADE TIME and WAIT TIME which are going to be added to the single Chase. If you do not make any adjustments, the system will remember the last FADE TIME or WAIT TIME. 6. Press the button MUSIC/BANKCOPY 7. Press the button MANUAL/REC, all LEDs blink for 3 times, all the programmed scenes in the Bank will join the Chase. 8. Repeat Step 3-7 can join 200 scenes max to the chase. 9. Finally press the button CHASE to store the chase then exit the programming state.
PAGE 29
4. Use Jog wheel #2 to view the steps, the strobe display [002] indicate programmable step number. 5. Use jog wheel #1 to select the bank number of the scene, press number button 1-20 to open. 6. Use the Jog wheel #3, #4 to adjust the FADE TIME and WAIT TIME which are going to be added to the single Chase. If you do not make any adjustments, the system will remember the last FADE TIME or WAIT TIME. 7.
PAGE 30
3. Press the button 1-20 to select the chase number. 4. Use the Jog wheel #2 to select the position of inserted steps. 5. Press the button TAP/INSERT to insert a step following the present position. 6. Use the Jog wheel #1 to select the Bank number of the inserted scene. 7. Press the number button 1-20 to select the scene to be inserted. 8. Use the Jog wheel #3, #4 to adjust the CHASE FADE TIME and WAIT TIME. If you do not make any adjustments, the system will remember the last FADE TIME or WAIT TIME.
PAGE 31
11. Press the button CHASE to store the chase and exit the chase programming state. 12. Press the button PROGRAM for 3 seconds to exit Program mode, the LED goes out indicating this operation. 2.11 Deleting steps from program 1. Enter Program mode. 2. Press the button CHASE use jog wheel #1 to select the page number, choose the programming chase. 3. Press the number button 1-20 to select the chase number to delete from. 4. Use Jog wheel #2 to select the scene location you want to delete. 5.
PAGE 32
8. Press the button PROGRAM for 3 seconds to exit Program mode, the LED goes out indicating this operation. 2.12 Deleting a chase 1. Enter Program mode. 2. Press the button CHASE, use jog wheel #1 to select the page number, choose the programming chase. 3. Press the button AUTO/DEL. 4. Press the number button 1-20 to select the chase to be deleted, all LEDs blink for 3 times to indicate that you have successfully delete the chase. 5. Repeat the steps 2-4 to delete more chases. 6.
PAGE 33
4. Move the FADERS1-24 to change COLOUR/GOBO channel values (The codes of the channel feature of ARRT CODE are “C” and “G” in the fixtures bank) output for the convenience to check other channels but the channel output will not be stored in the preset. 5. Press the button MANUAL/REC at this moment all LEDs on buttons CUE, OVERRIDE, CENTRE, FIXTURE GROUP, PRESET, CHASE, BANK, BLACKOUT blink at the same time. 6. Press the button PRESET. 7. Use Jog wheel #1 to select the preset group number 1-20. 8.
PAGE 34
3. Roll the Jog wheel #1 to select Preset groups 1-20. 4. Press the number button 1-20 to open the to be edited preset. 5. Press FIXTURE button. 6. Press the number button 1-20 to select the concerned fixtures to program Preset. 7. Move FADER 1-24 to change COLOUR/GOBO channel values (The codes of the channel feature of ARRT CODE are “C” and “G” in the fixtures bank) output for the convenience to check other channels but the channel output will not be stored in the preset. 8.
PAGE 35
10. Press number button 1-20 to select the opened Preset, all LEDs blink for 3 times to indicate that you have successfully edited the Preset. 11. Press PROGRAM button for 3 seconds to exit Program mode, the LED goes out indicating this operation. NOTE: If you press different buttons in step 4 and 10, the preset in step 4 will cover the one in step 10. 2.15 Programming a fixture group 1. Enter Program mode. 2. Press FIXTURE button. 3.
PAGE 36
8. Press PROGRAM button 3 seconds to exit Program mode, the LED goes out indicating this operation. 2.16 Fixture group editing 1. Enter Program mode. 2. Press FIXTURE GROUP button. 3. Press the number button 1-20 to select the fixture group number to be edited. 4. Press FIXTURE button. 5. Press the number button 1-20 to select one or more fixtures to make the fixture group. 6.
PAGE 37
8. Press the number button 1-20 to select the fixture group number you selected in step 2, all LEDs blink for 3 times 9. Press PROGRAM button for 3 seconds to exit Program mode, the LED goes out indicating this operation. NOTE: If you press different buttons in step 3 and 7, the fixture group you selected in step 4 will cover the one in step 7. 2.17 Programming a centre 1. Enter Program mode. 2. Press FIXTURE button. 3. Press the number button 1-20 to select the concerned fixtures to be programmed. 4.
PAGE 38
6. Press CENTRE button. 7. Press the number button 1-20 to select the location to store the Centre all LEDs blink for 3 times to indicate that you have successfully stored a Centre position. 8. Repeat steps 2-7to program more Centre positions. 9. Press PROGRAM button for 3 seconds to exit Program mode, the LED goes out indicating this operation. 2.18 Centre editing 1. Enter Program mode. 2. Press CENTRE button. 3. Press the number button1-20 to select the edited Centre position number. 4.
PAGE 39
6. Move FADERS 1-24 and use Jog wheel #3, #4 to change the centre position of PAN, TILT where you desired. (The codes of the channel feature of ARRT CODE are “P”, “PF”, “T”, “TF” in the fixtures bank) for the convenience to check other channels, there would be some output of the channels, but the channel output will not be stored in the centre. 7. Press MANUAL/REC button, at this moment, all LEDs on CUE, OVERRIDE, CENTRE, FIXTURE GROUP, PRESET, CHASE, BANK, BLACKOUT blink at the same time. 8.
PAGE 40
4. Use FADERS 1-24 and 4 Jog wheels to adjust the selected fixture to your desired effect. 5. Press MANUAL/REC Button, at this moment, all LEDs on CUE, OVERRIDE, CENTRE, FIXTURE GROUP, PRESET, CHASE, BANK, BLACKOUT blink at the same time. 6. Press OVERRIDE button. 7. Press the number button 1-20 to select the to be stored Override number, all LEDs blink for 3 times to indicate that you have successfully preset an Override effect. 8. Repeat steps 2-7 to program other Override effects. 9.
PAGE 41
4. Press FIXTURE button. 5. Press the number button 1-20 to select the concerned fixtures to be edited with Override. 6. Use FADERS1-24 and 4 Jog wheels to adjust the selected fixture to your desired effect. 7. Press MANUAL/REC button, at this moment, all LEDs on CUE, OVERRIDE, CENTRE, FIXTURE GROUP, PRESET, CHASE, BANK, BLACKOUT blink at the same time. 8. Press OVERRIDE button. 9.
PAGE 42
2.21 Program a cue 1. Enter Program mode. 2. Press CUE button use jog wheel #1 to select the page number. 3. Press the number button 1-20 to select the to be stored CUE number, at this moment, all LEDs on CHASE are lit and all LEDs on the number button which have saved CHASE will blink. Turn jog wheel #1 should change the page number. 4. Press the number button 1-20 to select the Chase number which is to be stored to CUE, the LEDs on the chosen number buttons will be lit. 5.
PAGE 43
4. Press the number button to edit the Chase in CUE. 5. Press MANUAL/REC button, all LEDs blink for 3 times to indicate that you have successfully edited a CUE. 6. Press PROGRAM button for 3 seconds to exit Program mode, the LED goes out indicating this operation. 2.23 Delete a cue 1. Enter Program mode. 2. Press and hold AUTO/DEL button. 3. Press CUE use jog wheel #1 to select the page number. 4.
PAGE 44
3.24 Store a blackout scene Blackout Scene is a special scene of Blackout mode set in By Black Scene. 1. Enter Program mode. 2. Press the number button1-20 to select one or more fixtures. 3. Move FADERS1-24 to vary the channel outputs or use Jog wheel #1, #2 to adjust PAN and PAN FINE or use Jog wheel #3, #4 to adjust TILT, TILT FINE. 4.
PAGE 45
3.1 Running scene Scene can be open solely in the manual mode, but in the sound or auto mode it should circulate with some BANK. 1.Manual Mode 1. Press BANK Button. 2. Press MANUAL/REC to into manual mode. The LED of MANUAL/REC will be on. 3. Use Jog wheel #1 to select the bank you anticipate. 4. Press number Button to open the scene. 2.Sound Mode 1. Press BANK Button. 2. Press MUSIC/BANK COPY Button to into sound mode, the LED of MUSIC/BANK COPY will be on 3.
PAGE 46
3.Auto Mode 1. Press BANK Button. 2. Press AUTO/DEL Button to enter auto mode, the LED of AUTO/DEL will on. 3. Use Jog wheel #1 to select the bank you anticipate. 4. Use Jog wheel #3 or #4 to adjust current FADE TIME or WAIT TIME, or use TAP/ INSERT Button to adjust the speed of the scene. NOTE: When you press TAP/INSERT to adjust the speed, adjusting the running speed of the scene is based on the interval of pressing the Press TAP /INSERT Button twice which no more than 10 minutes. 3.
PAGE 47
3. Press number Button 1-20 to select the program you anticipate.. 4. Use Jog wheel #2 to run the last or next step. 2.Sound Mode 1. Press CHASE Button, use jog wheel #1 to select chase page. 2. Press MUSIC/BANK COPY Button to enter sound mode, the LED of MUSIC/BANK COPY will be on. 3. Press number Button 1-20 to select the program you anticipate, you can choose much more than one CHASE, and they will run with the music on the train that you select them.
PAGE 48
3. Press number Button 1-20 to select the program you anticipate. You can choose much more than one CHASE, and they will run on the train that you select them. 4. Setting to CHASE RUN BY INSIDE TIME, then it will run as the FADE TIME or FADE TIME of the step that you set when store the chase. Setting to CHASE RUN BY OUTSIDE TIME , then it will run as the FADE TIME or FADE TIME you set last time, you can also adjust by turn the joy wheel #3 or #4, or use TAP/INSERT Button to adjust the speed.
PAGE 49
B. When CUE or CHASE or BANK running, press OVERRIDE button, then use 1-20 button to open the effect that be programmed. 4. Fog machine operation Set up another 481CH DMX signal to control the fog machine (keep out the 482CH). Fog Machine operation: 1. Connection: connect the fog machine with the DMX information. 2.
PAGE 50
Use jog wheel #3 or #4 to set the value of DIMMER (0-255) or SPEED (0-255) that out of the strobe light. Press ENTER/MAIN MENU button to store, press PROGRAM button to exit. 3. Control: Press STROBE button then the controller will control the DMX strobe light with the value of the DMX be set, and the light strobe in the speed that be set to the simulate strobe light. 6.
PAGE 51
MIDI Channel MIDI 1 Note number 80-99 Command Turn on or off Chase 41 ~ 60 MIDI 1 100-119 Turn on or off CUE4 1~60 MIDI 1 120~127 No function Bank 13 - Bank 16 MIDI 4 00 ~ 79 Turn on or turn off scenes from Bank 13 ~ 16 Bank 17 - Bank 20 MIDI 5 00 ~ 79 Turn on or turn off scenes from Bank 17 ~ 20 Bank 21 - Bank 24 MIDI 6 00 ~ 79 Turn on or turn off scenes from Bank 21 ~ 24 Bank 25 - Bank 28 MIDI 7 00 ~ 79 Turn on or turn off scenes from Bank 15 ~ 28 Bank 29 - Bank 32 MIDI 8 00 ~ 7
PAGE 52
8. Profile create notice PROFILE.CIF (as the profile cyclostyle) The finished file should use a short name below 8 characters, All use capital letters and suffix with CIF transitorily. (IL-2420 controller nonsupport long file name) or the controller can’t read up the profile information. IM-1200S.CIF is the profile of ACME IM-1200S Enactment special code, so the controller should distil some channel characteristic to manage.
PAGE 53
;| | | CHANNEL FUNCTION ;| | | | 1 N „SHUT“; „SHUTTER“ 2 D „DIM“; „DIMMER“ 3 C „C_C“; „CYAN“ 4 C „C_M“; „MAGENTA“ 5 C „C_Y“; „YELLOW“ 6 C „CTC“; „CTC“ 7 C „COLR“; „COLOUR“ 8 G „GOB1“; „GOBO1“ 9 G „R_G1“; „GOBO 1 ROT“ 10 G „RG1L“; „GOBO 1 ROT LOW“ 11 G „GOB2“; „GOBO2“ 12 G „R_G2“; „GOBO 2 ROT“ 13 G „RG2L“; „GOBO 2 ROT LOW“ 14 N „EFFT“; „EFFECT“ 15 N „R_EF“; „ROT EFFECT“ 16 N „IRIS“; „IRIS“ 17 N „FCUS“; „FOCUS“ 18 N „ZOOM“; „ZOOM“ 19 P „PAN“; „PAN“ 20 PF „P_F“; „PAN
PAGE 54
; ARRT CODE MAX 2 CHARACTER ; | DISPLAY INFORMATION MAX 4 CHARACTER DON‘T HAVE BLANK ; | | CHANNEL FUNCTION ; | | | ; D „DIM“; „DIMMER“ ; N „SHUT“; „SHUTTER“ ; P „PAN“; „PAN“ ; PF „P_F“; „PAN FINE“ ; T „TILT“; „TILT“ ; TF „T_F“; „TILT FINE“ ; PT „PT_S“; „P/T SPEED“ ; G „GB1“; „GOBO 1“ ; G „RGB1“; „GOBO 1 ROT“ ; G „GB2“; „GOBO 2“ ; G „RGB2“; „GOBO 2 ROT“ ; G „GB3“; „GOBO 3“ ; G „ROB3“; „GOBO 3 ROT“ ; C „COL1“; „COLOUR 1“ ; C „COL2“; „
PAGE 55
; N „F_B“; „FUNCTION B“ ; N „F_C“; „FUNCTION C“ ; N „F_D“; „FUNCTION D“ ; N „F_E“; „FUNCTION E“ ; N „F_F“; „FUNCTION F“ ; N „F_G“; „FUNCTION G“ ; N „F_H“; „FUNCTION H“ ; N „F_I“; „FUNCTION I“ ; N „F_J“; „FUNCTION J“ ; N „F_K“; „FUNCTION K“ ; N „F_L“; „FUNCTION L“ Note: 1. All the character must be capitalization except commentary which after”;”. 2.