User Guide

Thomann GmbH • Hans-Thomann-Straße 1 • 96138 Burgebrach • www.thomann.de • [e-mail] DocID: 523764_25.04.2022
Vintage Bowl 30 RGBA IR
EN
Quick start guide
This quick start guide contains important information on the safe operation of the
product. Read and follow the safety advice and instructions given. Retain the quick
start guide for future reference. If you pass the product on to others please include
this quick start guide.
Features
• Decorative element for stages and bars
• 40-W LED, 4in1, RGBA
• Sturdy metal construction
• Illuminated re ector with a unique look
• Automatic colour change and fade programmes
• Static colours selectable
• Fixed power cable
• Control via IR remote control (supplied)
Safety instructions
Intended use
This device is intended for use as an electronic lighting e ect by means of LED tech-
nology. The device is designed for professional use and is not suitable for use in
households. Any other use or use under other operating conditions is considered to
be improper and may result in personal injury or property damage. No liability will be
assumed for damages resulting from improper use.
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are
not within reach of babies and young children. Choking hazard! Ensure
that children do not detach any small parts from the product. They could
swallow the pieces and choke! Never let children unattended use electri-
cal devices.
Electric shock caused by high voltages inside
Within the device there are areas where high voltages may be present.
Never remove any covers. There are no user-serviceable parts inside. Do
not use the device if covers, protectors or optical components are missing
or damaged.
Electric shock caused by short-circuit
Do not modify the mains cable or the plug. Failure to do so could result
in electric shock/death or  re. If in doubt, seek advice from a registered
electrician.
Risk of injury caused by falling objects
Make sure that the installation complies with the standards and rules that
apply in your country. Always secure the device with a secondary safety
attachment, such as a safety cable or a safety chain.
Eye damage caused by high light intensity
Never look directly into the light source.
Risk of epileptic shock
Strobe lighting can trigger seizures in photosensitive epilepsy. Sensitive
persons should avoid looking at strobe lights.
Risk of overheating
The distance between light output and the illuminated surface must be
more than 1.5 m (19.7 in). Provide suffi cient ventilation. The ambient tem-
perature must always be below 40 °C (104 °F).
Risk of  re
Do not block areas of ventilation. Do not install the device near any direct
heat source. Keep the device away from naked  ames.
Use of stands
When mounting the device onto a stand, ensure that the stand is in a safe
and stable position and that the weight of the device does not exceed the
maximum permissible load capacity of the stand.
Operating life of the LEDs
Extend the operating life of the device by regular breaks and by avoiding
frequent switching on and o . The device is not suitable for continuous
operation.
For technological reasons, the light output of LEDs decreases over their
lifetime. This e ect increases with higher operating temperature. You can
extend the service life of the illuminants by providing adequate ventilati-
on and operating the LEDs with the lowest possible brightness.
Where to use the product
Never use the product
• outdoors
• in direct sunlight
• in conditions of extreme temperature or humidity
• in extremely dusty or dirty areas
• at locations where the unit can become wet
General handling
• To prevent damage, never use force when handling the product.
• Never immerse the product in water. Just wipe it with a clean dry cloth.
Do not use liquid cleaners such as benzene, thinners or  ammable
cleaning agents.
Installation
You can install the device in hanging or standing position.
The safety rope must be attached to the safety rope eyelet on the
back of the device.
When in use, the device must always be attached to a solid surface or
an approved truss. Use the openings provided on the double bracket
for attaching.
Always work from a stable platform whenever installing, moving or
servicing the unit. In doing so, the area underneath the unit must be
cordoned o .
Please note that this device must not be connected to a dimmer.