Owner's Manual WARNING Exercise can present a health risk. Consult a physician before beginning any exercise program with this equipment. If you feel faint or dizzy, immediately discontinue use of this equipment. Serious bodily injury can occur if this equipment is not assembled and used correctly. Serious bodily injury can also occur if all instructions are not followed. Keep others and pets away from equipment when in use. Always make sure all bolts and nuts are tightened prior to each use.
TABLE OF CONTENTS Page Safety Instructions Before You Begin Hardware Identification Chart Assembly Instructions Setting up The Accessories Storage Maintenance Page Warm-up and Cool-Down Warranty Product Parts Drawing Parts List Notes Fax/Mail Ordering Form 2 4 5 6 14 15 15 16 17 18 19 21 22 SAFETY INSTRUCTIONS WARNING: To reduce the risk of serious injury, read the following Safety Instructions before using the VIPER VG1500TM Leverage System. 1. Read all warnings posted on the VG1500TM Leverage System.
CALL US FIRST THANK YOU FOR PURCHASING THE VIPER VG1500TM Leverage System Your VIPER VG1500TM Leverage System does require assembly. Please follow the assembly steps set forth in this manual. Within a short time you will be getting your body into shape and on your way to a achieving a healthier lifestyle. Should you have any questions, please call our Customer Service Department toll-free number, 1 (800) 375-7520 Monday - Thursday, 7:30 A.M. - 5:00 P.M. Central Time. Friday, 8:00 A.M. - 3:00 P.M.
BEFORE YOU BEGIN Thank you for choosing the VG1500TM Leverage System. We take great pride in producing this quality product and hope it will provide many hours of quality exercise to make you feel better, look better and enjoy life to its fullest. Yes, it's a proven fact that a regular exercise program can improve your physical and mental health. Too often, our busy lifestyles limit our time and opportunity to exercise.
HARDWARE IDENTIFICATION CHART This chart is provided to help identify the hardware used in the assembly process. Place the washers, the end of the bolts, or screws on the circles to check for the correct diameter. Use the small scale to check the length of the bolts and screws. 3/16" 1/4" 5/16" 3/8" 1/2" INCHES 0 1/2 1 1/2 2 1/2 3 1/2 4 1/2 5 1/2 6 in. mm.
ASSEMBLY INSTRUCTIONS Place all parts from the box in a cleared area and position them on the floor in front of you. Remove all packing materials from your area and place them back into the box. Do not dispose of the packing materials until assembly is completed. Read each step carefully before beginning. If you are missing a part please call our toll-free number for assistance 1 (800) 375-7520 or e-mail us at: parts@staminaproducts.
ASSEMBLY INSTRUCTIONS FRONT REAR STEP 3 Attach the LOWER UPRIGHT(6) to the BASE FRAME(1) with the SUPPORT BRACKET(5), HEX BOLTS (M12x1.75x70mm)(72), WASHERS(M12)(80), and NYLOCK NUTS(M12x1.75)(82). Do not tighten the bolts. Attach the LOW UPRIGHT(6) to the REAR STABILIZER(2) with HEX BOLTS(M12x1.75x70mm)(72), WASHERS(M12)(80), and NYLOCK NUTS(M12x1.75)(82). Tighten all bolts, including the bolts for STEP 2. STEP 4 Attach the LEVER ARM(8) to the LOWER UPRIGHT(6) with HEX BOLT(M12x1.
ASSEMBLY INSTRUCTIONS FRONT Large Ball End A B D F E C Small Ball End REAR STEP 6: Run the SMALL BALL END of the CABLE(45) through the slot at the top end of the UPRIGHT(7). Attach the CABLE(45) to the UPRIGHT(7) at "A" with the LARGE PULLEY(44), a HEX BOLT (M10x1.5x95mm)(70), two WASHERS(M10)(81), and a NYLOCK NUT(M10x1.5)(83). Run the CABLE(45) through the pulley bracket on the UPRIGHT(7) at "B". Attach the CABLE(45) to the pulley bracket with a PULLEY(43), a HEX BOLT(M10x1.
ASSEMBLY INSTRUCTIONS BACK VIEW STEP 9 Refer to the inset drawing. Attach the SLIDER SUPPORT(14) to the LOWER UPRIGHT(6) with HEX BOLT (M12x1.75x160mm)(77), WASHERS(M12)(80), and NYLOCK NUT(M12x1.75)(82). Do not over tighten the bolt, as the SLIDER SUPPORT(14) must be able to pivot smoothly. STEP 10 Pull the SPRING PIN(34) on the SLIDER SUPPORT(14). Then insert the ADJUSTMENT BAR(13) into the SLIDER SUPPORT(14) and lock in the top adjustment hole with the SPRING PIN(34).
ASSEMBLY INSTRUCTIONS FRONT REAR STEP 12 Attach the SEAT FRAME(9) to the LOWER UPRIGHT(6) with HEX BOLTS(M12x1.75x100mm)(75), WASHERS(M12)(80), and NYLOCK NUTS(M12x1.75)(82). STEP 13 Attach the LEG LIFT(10) to the SEAT FRAME(9) with HEX BOLT(M12x1.75x90mm)(74), WASHERS (M12)(80), and NYLOCK NUT(M12x1.75)(82). STEP 14 Run the CABLE(45) through the slot in the LEG LIFT(10). Attach the CABLE(45) to the LEG LIFT(10) with a PULLEY(43), a BOLT(M10x1.5x60mm)(69), two WASHERS(M10)(81), and a NYLOCK NUT(M10x1.
ASSEMBLY INSTRUCTIONS STEP 16 Attach the FOAM SUPPORTS(15) to both sides of the LOWER UPRIGHT(6) with HEX BOLTS (M12x1.75x100mm)(75), WASHERS(M12)(80), and NYLOCK NUTS(M12x1.75)(82). STEP 17 Attach the HEAD REST(35) and BACK CUSHION(36) to the BACK SUPPORT(12) with HEX BOLTS (M10x1.5x25mm)(67) and WASHERS(M10)(81). STEP 18 Attach the SEAT CUSHION(37) to the SEAT POST(11) with HEX BOLTS(M10x1.5x25mm)(67) and WASHERS(M10)(81). Pull the SPRING PIN(34) on the SEAT FRAME(9).
ASSEMBLY INSTRUCTIONS R Screw hole Slot FRONT R R L L REAR L STEP 19: There is an "L" decal on the LEFT LEVERAGE ARM(17), and an "R" decal on the RIGHT LEVERAGE ARM(18). Slide the RIGHT LEVERAGE ARM(18) onto the shaft at right side of the ARM BRACE(16) and secure with LARGE WASHER(M12xø31mm)(79) and NYLOCK NUT(M12x1.75)(82). STEP 20: Attach the RIGHT WEIGHT BAR(20) to the RIGHT LEVERAGE ARM(18) with HEX BOLTS (M12x1.75x80mm)(73), WASHERS(M12)(80), and NYLOCK NUTS(M12x1.75)(82).
ASSEMBLY INSTRUCTIONS Ring STEP 22 Slide a FOAM ROLLER(39) onto a SUPPORT TUBE(38) and screw a SECURING CAP(41) onto the end of the SUPPORT TUBE(38). Insert the other end of the SUPPORT TUBE(38) through the hole in the LEG LIFT(10). Slide another FOAM ROLLER(39) over the protruding end of the SUPPORT TUBE(38) and screw a SECURING CAP(41) onto the end of the SUPPORT TUBE(38). Repeat to assemble the FOAM ROLLERS(39) into the hole in the SEAT FRAME(9).
SETTING UP THE ACCESSORIES LAT BAR(49) Attach the LAT BAR(49) to the CABLE(45) with a QUICK LINK(47). For some exercises, the SHORT CHAIN(56) or LONG CHAIN(55) should be attached between the LAT BAR(49) and the CABLE(45) with two QUICK LINKS(47). STRAIGHT BAR HANDLE(51), ANKLE CUFF(53) The STRAIGHT BAR HANDLE(51) and ANKLE CUFF(53) can be attached to the ball end of the CABLE(45) at the bottom of the LEG LIFT(10) with two QUICK LINKS(47) and one of the CHAINS(55, 56).
STORAGE To store the VG1500TM Leverage System simply keep it in a clean dry place. MAINTENANCE The safety and integrity designed into the VG1500TM Leverage System can only be maintained when the VG1500TM Leverage System is regularly examined for damage and wear. Special attention should be given to the following: 1. Verify that the warning and notice labels are in place and easy to read. Call Stamina Products immediately (1-800-375-7520) for a replacement label if labels are missing or damaged. 2.
WARM-UP and COOL-DOWN Warm-up The purpose of warming up is to prepare your body for exercise and to minimize injuries. Warm up for two to five minutes before strength-training or aerobic exercising. Perform activities that raise your heart rate and warm the working muscles.
LIMITED WARRANTY MODEL 50-3000 WARRANTY Stamina Products, Inc. warrants that this product will be free from defects in materials and workmanship under normal use, service and proper operation for a period of 90 days on the parts and three years on the frame from the date of the original purchase from an authorized retailer.
PRODUCT PARTS DRAWING BACK FRONT 18
PARTS LIST DIAGRAM# 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 PART NAME Base Frame Rear Stabilizer Rear Support Foot Plate Support Bracket Lower Upright Upright Lever Arm Seat Frame Leg Lift Seat Post Back Support Adjustment bar Slider Support Foam Support Arm Brace Left Leverage Arm Right Leverage Arm Left Weight Bar Right Weight Bar Left Handlebar Right Handlebar Handlebar Hand Grip Sleeve Handlebar Foam Grip Large
PARTS LIST DIAGRAM# 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 PART NAME Hook Sleeve Lat Bar Foam Grip Straight Bar Handle Hand Grip Ankle Cuff Ab Curl Strap Long Chain (10 Links) Short Chain (6 Links) Stand Bumper Rectangular Plug (30mm x 60mm) Rectangular Plug (50mm x 75mm) Square Plug (50mm x 50mm) Round Plug (25.
NOTES 21
FAX/MAIL ORDERING FORM Please do not return the product. For your convenience, Stamina has a Customer Service Department with a toll-free number. Should a part be missing or a defective part found, please call 1 (800) 375-7520 (in the U.S.) from 7:30 A.M. to 5:00 P.M. Central Time, Monday through Thursday and 8:00 A.M. to 3:00 P.M. on Friday or fill out the fax sheet ordering form below and fax it to (417) 889-8064.