MATRIX GX1280S 25 Watt VHF/FM Marine Transceiver Owner's Manual Submersible DSC distress call automatically broadcasts lat/long and vessel ID8 DSC position request function and NMEA data input/output Latitude/Longitude and SOG/COG display8 Channel name capability Optional RAM+ second station remote microphone Versatile user-programmable Scanning, Priority Scan and Dual Watch NOAA Weather Alert One-button access to Channel 16 and 9 Access to all US, Canadian and International channels
TABLE OF CONTENTS SAFETY/WARNING INFORMATION ................................................................ 4 FCC RADIO LICENSE INFORMATION ............................................................ 5 FCC NOTICE ..................................................................................................... 6 GETTING STARTED ......................................................................................... 7 ABOUT VHF RADIO ....................................................................
TABLE OF CONTENTS 8 9 10 11 12 13 7.4 ADDITIONAL DIGITAL SELECTIVE CALLING INFORMATION .................. 33 7.5 DSC DISTRESS CALL ................................................................................... 33 7.5.1 Transmitting a DSC Distress Call .............................................................. 33 7.5.2 Receiving a DSC Distress Call .................................................................. 34 7.6 ALL SHIPS CALL ...........................................................
SAFETY / WARNING INFORMATION This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining the minimum separation distance of 0.6 m (2 feet). Failure to observe these restrictions will result in exceeding the FCC RF exposure limits. Antenna Installation: The antenna must be located at least 0.
FCC RADIO LICENSE INFORMATION Standard Horizon radios comply with the Federal Communication Commission (FCC) requirements that regulate the Maritime Radio Service. STATION LICENSE An FCC ship station license is no longer required for any vessel traveling in U.S. waters (except Hawaii) which is under 20 meters in length.
FCC NOTICE NOTICE Unauthorized changes or modifications to this equipment may void compliance with FCC Rules. Any change or modification must be approved in writing by STANDARD HORIZON. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
GETTING STARTED ABOUT VHF RADIO The radio frequencies used in the VHF marine band lie between 156 and 158 MHz with some shore stations available between 161 and 163 MHz. The marine VHF band provides communications over distances that are essentially “line of sight” (VHF signals do not travel well through objects such as buildings, hills or trees). Actual transmission range depends much more on antenna type, gain and height than on the power output of the transmitter.
COAXIAL CABLE VHF antennas are connected to the transceiver by means of a coaxial cable – a shielded transmission line. Coaxial cable is specified by it’s diameter and construction. For runs less than 20 feet, RG-58/U, about 1/4 inch in diameter is a good choice. For runs over 20 feet but less than 50 feet, the larger RG-8X or RG213/U should be used for cable runs over 50 feet RG-8X should be used. For installation of the connector onto the coaxial cable refer to the figure below.
1 GENERAL INFORMATION 1.1 INTRODUCTION The STANDARD HORIZON MATRIX is a VHF/FM transceiver designed for use in the frequency range of 156.025 to 163.275 MHz. The MATRIX can be operated from 11 to 16 VDC and has a switchable RF output power of 1 watt or 25 watts. The MATRIX is capable of RTCM SC101 DSC (Digital Selective Calling) operation and second station operation with the use of the improved optional RAM+ mic (CMP25 remote-control speaker/microphone with display).
2 PACKING LIST When the package containing the transceiver is first opened, please check it for the following contents: GX1280S MATRIX Transceiver (White/Black) Mounting Bracket and attaching hardware Owner’s Manual Quick-Reference Card Power Cord Dust Cover 3 OPTIONS MMB-84 ........................................................................ Flush-Mount Bracket CMP25B/W ............ Remote-Access Microphone (RAM+ Mic, Black/White) CT-100 .............................................
4 INSTALLATION 4.1 LOCATION The radio can be mounted at any angle.
radio. RG58 cable can be used for distances less than 25 feet. 2. Connect the red power wire to a 13.8 VDC ±20% power source. Connect the black power wire to a negative ground. 3. If an optional remote extension speaker is to be used, refer to section 3.3 for connections. 4. It is advisable to have a Certified Marine Technician check the power output and the standing wave ratio of the antenna after installation. 4.
4.
4.5 CHECKING GPS CONNECTIONS After connections have been made between the MATRIX and the GPS, a small satellite icon will appear on the top right corner of the LCD display. To see additional GPS information press and hold the [H/L] (NAV) key until the MATRIX shows the Date, Time, SOG and COG. 4.6 CHANGING THE GPS TIME From the Factory the MATRIX shows GPS satellite time or UTC time. A time offset is needed to offset this time to show the local time in your area. 1.
4.7 CHANGING COG TO TRUE OR MAGNETIC Allows customizing the NAV data showing GPS Course Over Ground (COG). Factory default is True however following the steps below the COG can be changed to Magnetic. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appears. 2. Press the [CALL/SET] key, then select “TRUE MAG” in the “RADIO SETUP” menu with the CHANNEL selector knob. 3. Press the [CALL/SET] key. 4. Turn the CHANNEL selector knob to select “MAGNETIC” or “TRUE.” 5.
4.8 OPTIONAL MMB-84 FLUSH MOUNT INSTALLATION 1. Make a rectangular template for the flush mount measuring 2-5/8” H x 6-5/8” W. 2. Use the template to mark the location where the rectangular hole is to be cut. Confirm the space behind the dash or panel is deep enough to accommodate the transceiver (at least 6 inches deep). There should be at least 1/2 inch between the transceiver’s heatsink and any wiring, cables or structures. 3. Cut out the rectangular hole and insert the transceiver. 4.
4.9 OPTIONAL CMP25 RAM+ MIC INSTALLATION 1. Connect the RAM+ MIC Cable to the RAM MIC CONNECTOR on the rear panel, then tighten the Cable Nut (See Figure 3). 2. Referring to Figure 3, make a 1.2” (30 mm) hole in the wall, then insert the RAM+ MIC Cable into this hole. Connect the Gasket and Mount Base to the RAM+ MIC Cable Connector using the Nut. 3. Drill the four Screw holes (approx. 2 mm) on the wall, then install the Mounting Base to the wall using four screws. 4. Put the Rubber Cap on to the Nut.
5 CONTROLS AND INDICATORS NOTE This section defines each control of the transceiver. See Figure 4 for location of controls. For detailed operating instructions refer to chapter 6 of this manual. 5.1 CONTROLS AND CONNECTIONS POWER SWITCH/VOLUME CONTROL Turns the transceiver on and off as well as adjusts the audio volume. To turn the transceiver on press and hold this knob until the LCD turns on. To turn it off, press and hold this knob until the LCD turns off.
VOL/PWR 16/9 U.I.C WX MEM SCAN MATRIX IC DW NAV MENU H/L CALL SET DISTRESS PULL OPEN SQL Figure 4.
KEYPAD [16/9] Key Immediately recalls channel 16 from any channel location. Holding down this key recalls channel 9. Pressing the [16/9] key again reverts to the previous selected working channel. Secondary use Press and hold the [16/9] key then press the [WX] key to switch between USA, International and Canadian bands. [WX] Key Immediately recalls the previously selected NOAA weather channel from any channel. Secondary use 1.
[DW] / [IC] Key Scans for voice communications on CH16 and another selected channel until a signal is received on either channel. (Dual watch) NOTE: When the DSC SCANNING feature is enabled (see section 7.2 DSC SCAN), the radio watches for a transmission on CH16, another selected channel, and CH70 until a signal is received (Triple watch). Secondary use Press and hold [DW] key, when the optional RAM+ Mic is connected, intercom operation will operate between radio and RAM+ Mic.
ACCESSORY CONNECTION CABLE Connects the MATRIX to a GPS, and an external speaker. See section 3 OPTIONS for a list of speakers STANDARD HORIZON offers. DC INPUT CABLE Connects the radio to a DC power supply capable of delivering 12V DC. ANTENNA JACK Connects an antenna to the transceiver. Use a marine VHF antenna with an impedance of 50 ohms. PTT (Push-To-Talk) SWITCH Keys the transmitter when the transceiver is in radio mode.
6 BASIC OPERATION 6.1 RECEPTION 1. After the transceiver has been installed, ensure that the power supply and antenna are properly connected. 2. Press and hold the VOL/PWR knob until the radio turns on. 3. Turn the SQL knob fully counterclockwise. This state is known as “squelch off”. 4. Turn up the VOL/PWR knob until noise or audio from the speaker is at a comfortable level. 5. Turn the SQL knob clockwise until the random noise disappears. This state is known as the “squelch threshold.” 6.
6.4 SIMPLEX/DUPLEX CHANNEL USE Refer to the VHF MARINE CHANNEL CHART (page 63) for instructions on use of simplex and duplex channels. NOTE All channels are factory-programmed in accordance with FCC (USA), Industry Canada (Canada), and International regulations. Mode of operation cannot be altered from simplex to duplex or vice-versa. 6.5 USA, CANADA, AND INTERNATIONAL MODE 1. To change the modes, hold the [16/9] key and press the [WX] key.
6.7 NOAA WEATHER ALERT In the event of extreme weather disturbances, such as storms and hurricanes, the NOAA (National Oceanic and Atmospheric Administration) sends a weather alert accompanied by a 1050 Hz tone and subsequent weather report on one of the NOAA weather channels. When the Weather Alert feature is enabled (see section 8.5 WX ALERT), the transceiver is capable of receiving this alert if the following is performed: 1. Program NOAA weather channels into the transceiver’s memory for scanning.
6.9 EMERGENCY (CHANNEL 16 USE) Channel 16 is known as the Hail and Distress Channel. An emergency may be defined as a threat to life or property. In such instances, be sure the transceiver is on and set to CHANNEL 16. Then use the following procedure: 1. Press the microphone push-to-talk switch and say “Mayday, Mayday, Mayday. This is , , ” (your vessel’s name). 2. Then repeat once: “Mayday, ” (your vessel’s name). 3.
some of the channels available to non-commercial (recreational) boaters. Monitor your desired channel in advance to make sure you will not be interrupting other traffic, and then go back to either channel 16 or 9 for your initial contact. When the hailing channel (16 or 9) is clear, state the name of the other vessel you wish to call and then “this is” followed by the name of your vessel and your Station License (Call Sign).
By regulation, power is normally limited to 1 Watt on these channels. Your radio is programmed to automatically reduce power to this limit on these channels. However, in certain situations it may be necessary to temporarily use a higher power. See page 20 (H/L key) for means to temporarily override the low-power limit on these two channels. 6.
5. To start scanning, press the [SCAN] key. Scanning will proceed from the lowest to the highest programmed channel number and will stop on a channel when a transmission is received. 6. The channel number will blink during reception. 7. To stop scanning, press the [SCAN], [16/9], [WX], [CALL/SET], or PTT key. 6.16 PRIORITY SCANNING (P-SCAN) 1. Channel 16 is set as the priority channel and cannot be changed. 2.
6.18 VOICE SCRAMBLER If privacy of communications is desired, a CVS2500 voice scrambler (VS) can be installed in the transceiver. Contact your Dealer to have a CVS2500 installed. Refer to the section 8.9 VOICE SCRAMBLER to program the voice scrambler. 1. Turn on the transceiver. 2. Select a channel that was programmed for scrambler mode (“VS” will appear on the LCD).
7 DIGITAL SELECTIVE CALLING 7.1 GENERAL WARNING This radio is designed to generate a digital maritime distress and safety call to facilitate search and rescue. To be effective as a safety device, this equipment must be used only within communication range of a shorebased VHF marine channel 70 distress and safety watch system. The range of signal may vary but under normal conditions should be approximately 20 nautical miles.
SCAN” with the CHANNEL selector knob. 4. Press the [CALL/SET] key. 5. Turn the CHANNEL selector knob to select “ON”or “OFF.” 6. Press the [CALL/SET] key to store the selected setting. 7. To exit this menu and return to radio operation mode press the [16/9] key. 7.3 USCG DSC WATCH The USCG has plans to upgrade its VHF National Distress System (expected by 2005), so at the time of printing only larger vessels that are required to carry VHF DSC radios will be able to hear your distress transmission. 7.3.
ber will appear, and the first space will flash. 5. Select first number of your MMSI, then press the [CALL/SET] key to step to the next number. 6. Repeat step 5 to set your MMSI (up to nine digits). 7. When finished programming the number, press and hold the [CALL/SET] key to store the number in memory. 8. To exit this menu and return to radio operation mode press the [16/9] key. 7.
5. If an acknowledgement is received, select channel 16 and advise your distress situation. 6. If no acknowledgment is received, the distress call is repeated in 4 minute intervals until an acknowledgment is received. 7. When a DSC Distress acknowledgment is received, a distress alarm sounds and channel 16 is automatically selected. The LCD shows the MMSI of the ship responding to your distress. RECEIVED ACK: acknowledgment signal is received.
7.6 ALL SHIPS CALL The All Ships Call function allows contact to be established with other vessel stations without having their ID in the individual calling directory. Also, priority for the call can be designated as Urgency or Safety. URGENCY Call: This type of call is used when a vessel may not truly be in distress, but have a potential problem that may lead to a distress situation. This call is the same as saying PAN PAN PAN on channel 16.
7.6.2 Receiving an All Ships Call 1. When an all ships call is received, an emergency alarm sounds. The radio will automatically change to channel 16. 2. Press any key to stop the alarm. 3. Turn the CHANNEL selector knob to see the MMSI of the vessel transmitting the All Ships Call. 4. Monitor channel 16 or traffic channel until the URGENCY voice communication is completed. 7.
8. Repeat step 6 and 7 until the name is complete. The name can consist of up to eleven characters, if you do not use all eleven characters press the [CALL/SET] key to move to the next space. This method can also be used to enter a blank space in the name. To clear the previous letter, press the [H/L] key. 9. After the eleventh letter or space has been entered, press the [CALL/ SET] key to advance to the MMSI (Maritime Mobile Service Identity Number) number entry. 10.
5. Turn the CHANNEL selector knob to select “AUTO” or “MANUAL.” 6. Press the [CALL/SET] key to store the selected setting. 7. To exit this menu and return to radio operation mode press the [16/9] key. 7.7.3 Setting up Individual Call Ringer When a Individual call is received the radio will produce a ringing tone for 3 minutes. This selection allows the Individual Call ringer time to be changed. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appear. 2.
7.7.4 Transmitting an Individual Call This feature allows the user to contact another vessel with a DSC radio. This feature is similar to calling a vessel on CH16 and requesting to go to another channel. Select the traffic channel for voice communication. 1. Press the [CALL/SET] key. The “DSC OPERATION” menu will appear. 2. Turn the CHANNEL selector knob to select “INDIVIDUAL.” (To cancel, select “EXIT” with the CHANNEL selector knob or press the [16/9] key.) 3. Press the [CALL/SET] key.
7.7.5 Receiving an Individual Call When receiving an individual call, an acknowledgment must be sent back to the calling station. The MATRIX default setting is Automatic, but has a selection that allows you to manually send a reply before the radio will switch to the requested calling channel. This selection is useful if you want to see who is calling and requesting you to switch to a channel for communications, similar to caller id on a cellular phone. 1.
7.8 ADVANCED DSC CALLS 7.8.1 Group Call This feature allows the user to contact a group of specific vessels (example members of a yacht club) using DSC radios with Group call function to automatically switch to a desired channel for voice communications. 7.8.1.1 Setup a Group Call For this function to operate the same Group MMSI must be programmed into all the DSC VHF radios within the group of vessels that will be using this feature.
10. Turn the CHANNEL selector knob to scroll through numbers, 0-9. 11. To enter the desired number and move one space to the right press the [CALL/SET] key. Repeat procedure until all nine spaces of MMSI number are entered. 12. If a mistake was made entering in the name or the MMSI number repeat pressing the [CALL/SET] key until the wrong character is selected, then move the CHANNEL selector knob to correct the entry. 13. To store the data entered, press and hold the [CALL/SET] key. 14.
7.8.1.3 Receiving a Group Call 1. When a group call is received, the MATRIX will produce a ringing alarm sound. 2. The radio automatically switches to the requested channel. 3. Press any key to stop the alarm. 4. Monitor the channel for the person calling the Group for a message. 5. If you want to respond, monitor the channel to make sure it is clear, then press the PTT on the mic and talk to the calling ship(s).
7.8.2.1 Setting up Position Reply The MATRIX can be set up to automatically or manually send your position to another vessel. This selection is important if you are concerned about someone polling the position of your vessel that you may not want to. In the manual mode you will see the MMSI or persons name shown on the display allowing you to choose to send your position to the requesting vessel. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appear. 2.
5. Press the [CALL/SET] key to transmit the position request DSC call. 6. After a DSC position request is transmitted, the transceiver remains on channel 70 until position data is received from the polled vessel. 7. When the MATRIX receives the position from the polled vessel it is shown on the radio display and also transferred to the GPS Chart plotter. 8. If the MATRIX does not receive a reply, the LCD will display “ SEND” to prompt the user to send the call again or exit the mode.
4. When “REPLY” is selected, press the [CALL/SET] key. And the your position will be transmitted to the requesting vessel. 5. To exit from position request display, press any key. 7.8.3 Position Send The feature is similar to Position Request, however instead of requesting a position of another vessel this function allows you to send your position to another vessel. Your vessel must have an operating GPS receiver connected for the MATRIX to send the position.
7.8.3.2 Receiving a DSC Position Send Call When another vessel transmits their vessels location to the MATRIX the following will happen: 1. A ringing sound will be produced when the call is received. 2. Press the [16/9] key to stop ringing 3. The position from the vessel sending it's position will be shown on the display of the radio and also transferred to any Standard Horizon GPS Chart plotter if connected.
8 RADIO SETUP NOTE The optional RAM+ MIC CMP25 can be also change the SETUP menu. Refer to page 54 for details. 8.1 LAMP ADJUSTING Allows setting up the backlight intensity or to turn it off. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appears. 2. Press the [CALL/SET] key, then select “LAMP” in the “RADIO SETUP” menu with the CHANNEL selector knob. 3. Press the [CALL/SET] key. 4. Turn the CHANNEL selector knob to select the desired level.
8.3 TIME OFFSET Sets the time offset between local time and UTC (time GPS sends to radio). Time is displayed when GPS position (LAT/LON) is displayed by pressing the [H/L] key. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appears. 2. Press the [CALL/SET] key, then select “TIME SET” in the “RADIO SETUP” menu with the CHANNEL selector knob. 3. Press the [CALL/SET] key. 4. Turn the CHANNEL selector knob to select time offset from UTC.
8.4 KEY BEEP (ON/OFF) This selection allows the beep tone when a key is pressed to be turned off. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appears. 2. Press the [ CALL/SET ] key, then select “KEY BEEP” in the “RADIO SETUP” menu with the CHANNEL selector knob. 3. Press the [CALL/SET] key. 4. Turn the CHANNEL selector knob to select “ON” or “OFF.” 5. Press the [CALL/SET] key to set the key beep condition. 6. To exit this menu and return to radio operation mode press the [16/9] key.
8.6 VOICE SCRAMBLER (Operates only when the optional CVS2500 is installed) This menu is used to setup the channels to be scrambled and the scrambler code. NOTE This menu will not appear unless a CVS2500 is installed. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appears. 2. Press the [CALL/SET] key then select “SCRAMBLER” in the “RADIO SETUP” menu with the CHANNEL selector knob. 3. Press the [CALL/SET] key then select “CODE” in the “SCRAMBLER” menu with the CHANNEL selector knob.
8.7 CHANNEL NAMING This selection allows you to customize the name of a channel from the default name. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appear. 2. Press the [CALL/SET] key, then select “CH NAME” in the “RADIO SETUP” menu with the CHANNEL selector knob. 3. Press the [CALL/SET] key. 4. Turn the CHANNEL selector knob to select the channel to be named and press the [CALL/SET] key. 5. Turn the CHANNEL selector knob scroll through the alphabet and 0 - 9. 6.
8.8 TRUE MAGNETIC CHANGE (NAV display) Allows customizing the GPS COG (Course Over Ground) displayed on the LCD to be in True or Magnetic. 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appear. 2. Press the [CALL/SET] key, then select “TRUE MAG” in the “RADIO SETUP” menu with the CHANNEL selector knob. 3. Press the [CALL/SET] key. 4. Turn the CHANNEL selector knob to select “MAGNETIC” or “TRUE.” 5. Press the [CALL/SET] key to store the selected setting. 6.
9 RAM+ MIC OPERATION If the enhanced optional RAM+ Mic (CMP25) is connected to the remote microphone connector on the transceiver’s rear panel, the transceiver can use the remote control operation except for a few functions. The RAM+ Mic supplied with 23 feet (7 m) of routing cable and can be extended up to 70 feet (21 m) using three 23 feet extension cables model CT-100. The intercom operation can be used between the RAM+ Mic and the transceiver. 9.1 RAM+ MIC CONTROLS IC DW CALL SET NAV MENU WX U.I.
VOLUME KEY (VOL) Activates the volume adjusting mode. Press this key to activate the volume adjusting mode. Press the microphone’s [ ] or [ ] to adjust the volume. POWER SWITCH (PWR) Press and hold down this key to turn to the transceiver and RAM+ Mic on and off. PTT (Push-To-Talk) SWITCH Activates transmission. [H/L] KEY Toggles between high and low power.
[CALL/SET] Key The [CALL/SET] key functions as the enter key. Secondary use Press the [CALL/SET] key to access the DSC OPERATION menu. Press and hold the [CALL/SET] key to access the SETUP menu. [DW] Key Watches for a transmission on CH16 and another selected channel until either signal is received. (Dual watch) NOTE: When the DSC SCANNING feature is enabled (see section 7.
4. 5. 6. 7. 8. will appear on the LCD. After the message has been sent, the radio will sound a Distress Alarm. The transceiver “shadow-watches” for a transmission on CH16 or CH70 until an acknowledgment signal is received. “DISTRESS” and “WAITING” will appear on the LCD. If an acknowledgement is received, select channel 16 and advise your distress situation. If no acknowledgment is received, the distress call is repeated in 4 minute intervals until an acknowledgment is received.
9.2.2 Calling Hold down the [DW] key for 1 second or more, when the “INTERCOM” operation is activated. A calling beep is emitted twice from the transceiver speaker. 9.3 DSC/RADIO SETUP MODE The CMP25 can access the DSC / RADIO setup menu (refer to section 7 “DSC/RADIO SETUP” for details). However, the LAMP, CONTRAST, and KEY BEEP menu item which is accessed from the CMP25 only controls the CMP25’s display and speaker. DSC/RADIO Setup mode from the CMP25: 1.
10 MAINTENANCE The inherent quality of the solid-state components used in this transceiver will provide many years of continuous use. Taking the following precautions will prevent damage to the transceiver. • • • • Keep the microphone connected or the jack covered at all times to prevent corrosion of electrical contacts; Never key the microphone unless an antenna or suitable dummy load is connected to the transceiver.
10.2 FACTORY SERVICE In the unlikely event that the radio fails to perform or needs servicing, please contact the following: Standard Horizon Attention Marine Repair Department 10900 Walker Street Cypress, CA 90630 Telephone (800) 366-4566 An “RA” Return Authorization number is not necessary to send a product in for service. Include a brief note describing the problem along with your name, return address, phone number, and proof of purchase.
10.3 TROUBLESHOOTING CHART SYMPTON PROBABLE CAUSE Transceiver fails to power up. No DC voltage to the a. Check the 12VDC battery contransceiver, or blown nections and the fuse. fuse. b. The VOL/PWR knob needs to be pressed and held to turn the radio on. Transceiver blows fuse when connected to power supply. Reversed power wires. Check the power cable for DC voltage, or replace the fuse (6A 250V).
11. CHANNEL ASSIGNMENTS Tables on the following columns list the VHF Marine Channel assignments for U.S.A. and International use. Below are listed some data about the charts. 1. VTS. Where indicated, these channels are part of the U.S. Coast Guard’s Vessel Traffic System. 2. Alpha channel numbers, that is, channel numbers followed by the letter A (such as Channel 07A) are simplex channels on the U.S.A. or Canadian channel assignments whose counterparts in the International assignments are duplex channels.
5. Channels normally used by recreational boaters are those that include the term “non-commercial” in the Channel Use column of the chart. Some of these are shared with other users and some are used only in certain geographic regions. 6. Marine vessels equipped with VHF radios are required to monitor Channel 16. VHF MARINE CHANNEL CHART CH U C I S/D TX RX CHANNEL USE 01 X X D 156.050 160.650 Public Correspondence (Marine Operator) 01A X S 156.050 Port Operation and Commercial.
CH 23 23A 24 25 26 27 28 60 61 U C X X X X X X X X X X X X X 61A X X 62 62A X 63 63A X 64 X 64A X X 65 65A X X 66 66A X X 67 X X 68 69 X X X X 70 71 X X X X 72 73 X X X X 74 X X 75 76 77 77 78 X X X X 78A X X Page 64 VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 157.150 161.750 Public Correspondence (Marine Operator) S 157.150 U.S. Government Only X D 157.200 161.800 Public Correspondence (Marine Operator) X D 157.250 161.850 Public Correspondence (Marine Operator) X D 157.300 161.
CH 79 79A 80 80A 81 81A U C X X X X X X 82 82A 83 83A 83 84 85 86 87 88 88A WX01 WX02 WX03 WX04 WX05 WX06 WX07 WX08 WX09 WX10 X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 156.975 161.575 Port operation and Ship movement S 156.975 Commercial X D 157.025 161.625 Port operation, ship movement S 157.025 Commercial X D 157.075 161.675 Port operation, ship movement S 157.075 U.S.
Channel designator Points of communicaCarrier frequency tion (Intership and be- Channel (MHz) tween coast and ship designator Coast unless otherwise indiCoast Ship transmit cated) transmit transmit Carrier frequency (MHz) Ship transmit Port Operations 01A1 63A1 052 65A 66A 123 73 143 74 774 20A12 156.050 156.175 156.250 156.275 156.325 156.600 156.675 156.700 156.725 156.875 157.000 Intership only. Intership only.
4: Use of 156.875 MHz is limited to communications with pilots regarding the movement and docking of ships. Normal output power must not exceed 1 watt. 5: 156.375 MHz and 156.650 MHz are available primarily for intership navigational communications. These frequencies are available between coast and ship on a secondary basis when used on or in the vicinity of locks or drawbridges. Normal output power must not exceed 1 watt.
12.
ZON, appear to be defective or not up to factory specifications. STANDARD HORIZON may, at its option, repair or replace parts or subassemblies with new or reconditioned parts and subassemblies. Parts thus repaired or replaced are warranted for the balance of the original applicable warranty. STANDARD HORIZON will not warrant installation, maintenance or service of the Products. In all instances, STANDARD HORIZON’s liability for damages shall not exceed the purchase price of the defective Product.
TIES, EXPRESS OR IMPLIED AS TO THE MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR OTHERWISE, EXCEPT AS EXPRESSLY SET FORTH HEREIN. Some states do not allow the exclusion or limitation of incidental or consequential damages, or limitation on how long an implied warranty lasts, so the above limitations or exclusions may not apply. This warranty gives specific legal rights, and there may be other rights which may vary from state to state.
ON-LINE WARRANTY REGISTRATION THANK YOU for buying STANDARD HORIZON (a division of Vertex Standard) products! We are confident your new radio will serve your needs for many years! Please visit www.standardhorizon.com to register the MATRIX Marine VHF. It should be noted that visiting the Web site from time to time may be beneficial to you, as new products are released they will appear on the STANDARD HORIZON Web site. Also a statement regarding product support should be added to the manual.
13 SPECIFICATIONS Performance specifications are nominal, unless otherwise indicated, and are subject to change without notice. 13.1 GENERAL Channels ............................................ All USA, International and Canadian Input Voltage ........................................................................ 13.8 VDC ±20% Current Drain Standby ............................................................................................ 0.5 A Receive ...................................................
MEMO GX1280S Page 73
Marine Division of VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. WWW. standardhorizon.com E M Page 74 0 0 3 N 1 0 0 Copyright 2003 VERTEX STANDARD CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD.
