MATRIX GX3000S 25 Watt VHF/FM ITU Class D DSC Marine Transceiver Owner's Manual Waterproof construction Commercial grade ITU Class D DSC VHF Independent Channel 70 receiver built-in for continuous DSC watching 30 W Loud Hailer with listen back and 4 fog horns, Bells & Whistles Capable of connecting 2 optional enhanced CMP25 RAM+ second station remote microphone or VH-310 Handset Intercom between radio and second station microphone DSC position request and send functions with compat
TABLE OF CONTENTS 1 2 3 4 5 6 7 GENERAL INFORMATION ............................................................................................................. 4 PACKING LIST ............................................................................................................................... 4 OPTIONS ....................................................................................................................................... 4 SAFETY / WARNING INFORMATION .............................
TABLE OF CONTENTS 12 13 14 15 16 17 18 19 11.6 CALL WAITING DIRECTORY ............................................................................................ 46 11.6.1 Enabling the Call Waiting Feature ........................................................................... 46 11.6.2 Reviewing Received Calls Logged into the Call Waiting Directory ...................... 47 11.6.3 To Delete the Received Log From the “DSC Log” Directory ............................... 47 11.7 GROUP CALL .........
1 GENERAL INFORMATION The Vertex Standard GX3000S is a VHF/FM transceiver designed for use in the frequency range of 156.025 to 163.275 MHz. The GX3000S can be operated from 11 to 16 VDC and has a switchable RF output power of 1 watt or 25 watts. The GX3000S is a Class D DSC (Digital Selective Calling) VHF and includes a 30W PA with preprogrammed fog signals, bells and whistles. 2 connections are available for the RAM+ or VH-310 second station remote microphones.
4 SAFETY / WARNING INFORMATION This radio is restricted to occupational use, work related operations only where the radio operator must have the knowledge to control the exposure conditions of its passengers and bystanders by maintaining the minimum separation distance of 0.6 m (2 feet). Failure to observe these restrictions will result in exceeding the FCC RF exposure limits. Antenna Installation: The antenna must be located at least 0.
5 FCC RADIO LICENSE INFORMATION Vertex Standard radios comply with the Federal Communication Commission (FCC) requirements that regulate the Maritime Radio Service. STATION LICENSE An FCC ship station license is no longer required for any vessel traveling in U.S. waters (except Hawaii) which is under 20 meters in length.
6 FCC NOTICE NOTICE Unauthorized changes or modifications to this equipment may void compliance with FCC Rules. Any change or modification must be approved in writing by Marine Division of Vertex Standard. NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
7 GETTING STARTED 7.1 ABOUT VHF RADIO The radio frequencies used in the VHF marine band lie between 156 and 158 MHz with some shore stations available between 161 and 163 MHz. The marine VHF band provides communications over distances that are essentially “line of sight” (VHF signals do not travel well through objects such as buildings, hills or trees). Actual transmission range depends much more on antenna type, gain and height than on the power output of the transmitter.
7.3 COAXIAL CABLE VHF antennas are connected to the transceiver by means of a coaxial cable, a shielded transmission line. Coaxial cable is specified by it’s diameter and construction. For runs less than 20 feet, RG-58/U, about 1/4 inch in diameter is a good choice. For runs over 20 feet but less than 50 feet, the larger RG-8X should be used for cable runs over 50 feet RG213 should be used. For installation of the connector onto the coaxial cable refer to the figure below.
8 INSTALLATION 8.1 LOCATION The radio can be mounted at any angle.
8.
8.4 CHECKING GPS CONNECTIONS After connections have been made between the GX3000S and the GPS, a small satellite icon will appear on the top right corner of the LCD display. To see the additional GPS information, press and hold the [H/L(NAV)] key. The GX3000S shows the Date, Time, SOG and COG. 8.5 CHANGING THE GPS TIME From the Factory the GX3000S shows GPS satellite time or UTC time. A time offset is needed to show the local time in your area. 1.
8.6 CHANGING THE TIME LOCATION Sets the radio to show UTC time or local time with the offset inputted in section 8.5 Changing the GPS Time. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Time Disp” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select “UTC” or “Local.” 5. Press the [ENT] key to store the selected setting. 6.
8.8 RECEIVER AUDIO TONE CONTROL Allows the treble and bass of the speaker audio to be adjusted for best listening in noisy enviroments. The effect is similar to adjusting a the treble and bass controls on a stereo. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “TONE CONT.” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key, then select “BASS” with the CHANNEL selector knob. 4.
8.9 OPTIONAL MMB-84 FLUSH MOUNT INSTALLATION 1. To assist in flush mounting, a template has been included. Use this template to find the mounting location. 2. Use the template to mark the location where the rectangular hole is to be cut. Confirm the space behind the dash or panel is deep enough to accommodate the transceiver (at least 6 inches or 15 cm deep). There should be at least 1/2 inch (1.3 cm) between the transceiver’s heatsink and any wiring, cables or structures. 3.
8.10 OPTIONAL ENHANCED RAM+ SECOND STATION MIC AND/OR VH-310 HANDSET INSTALLATION The GX3000S is capable of using up to 2 Enhanced RAM+ mics or VH-310 handsets to remotely control the Radio, DSC, and Distress functions. In addition the GX3000S can operate as a full function intercom system when either the RAM+ or VH-310 is connected. 1. Connect the Routing Cable to the one of the Remote Mic eight pin connector on the rear panel, then tighten the Cable Nut (See Figure 2). 2. Referring to Figure 3, make a 1.
Remote Mic or External Speaker Selection By default the RAM+ or VH-310 Handset internal speaker is turned on, however using the RAM+ mic (or VH-310 Handset) this speaker can be turned off so the external speaker can be used. RAM+ mic procedure 1. Press and hold the [CALL/SET] key. 2. Press the [ ] or [ ] key to select “RADIO SETUP.” 3. Press the [CALL/SET] key. 4. Press the [ ] key to until “EXT SPK” is shown and press the [CALL/SET] key. 5.
9 CONTROLS AND INDICATORS NOTE This section defines each control of the transceiver. See Figures for location of controls. For detailed operating instructions refer to section “10 BASIC OPERATION.” POWER SWITCH / VOLUME CONTROL (VOL/PWR) Turns the transceiver on and off as well as adjusts the audio volume. Press and hold this knob for one second to turn the radio on. Clockwise rotation of this knob increases the audio volume level. Press and hold this knob for two seconds to turn the radio off.
KEYPAD [16/9] Key Immediately recalls channel 16 from any channel location. Holding down this key recalls channel 9. Pressing the [16/9] key again reverts to the previous selected working channel. Secondary use Press and hold the [16/9] key then press the [WX] key to switch the Channel Group. [WX] Key Immediately recalls the previously selected NOAA weather channel from any channel.
[H/L(NAV)] Key Press this key to toggle the transmit output power between 25 W (High) and 1 W (Low) power. When the [H/L(NAV)] key is pressed while the transceiver is on channel 13 or 67, the power will temporarily switch from LO to HI power until the PTT is released. The [H/L(NAV)] key does not function on transmit inhibited and low power only channels. NOTE: 1W low power is indicated by LO on the display, when 25W high power is selected the display do not show an indication.
ANTENNA JACK Connects an antenna to the transceiver. Use a marine VHF antenna with an impedance of 50 ohms. REMOTE MIC CONNECTORS Connects the GX3000S to the enhanced RAM+ MIC (Remote Access Microphone) or the VH-310 Handset. Refer to section “13 ENHANCED RAM+ MIC OPERATION” or “14 VH-310 HEADSET OPERATION” for details. ACCESSORY CONNECTION CABLE Connects the GX3000S to a GPS, a PA speaker, and an external speaker. DC INPUT CABLE Connects the radio to a DC power supply capable of delivering 12V DC.
PTT (Push-To-Talk) SWITCH Keys the transmitter when the transceiver is in radio mode. If the transceiver is in the intercom mode (between the CMP25 RAM+ or VH-310 Headset and the GX3000S), or PA mode, it activates the GX3000S microphone for voice communications. MICROPHONE Transmits the voice message with reduction of background noise, using Clear Voice Noise Reduction Technology. NOTE: Be sure your mouth is about 1/2 inch from the mic hole for best performance.
MEMO GX3000S Page 23
10 BASIC OPERATION 10.1 RECEPTION 1. After the transceiver has been installed, ensure that the power supply and antenna are properly connected. 2. Press and hold the VOL/PWR knob until the radio turns on. 3. Turn the SQL knob fully counterclockwise. This state is known as “squelch off”. 4. Turn up the VOL knob until noise or audio from the speaker is at a comfortable level. 5. Turn the SQL knob clockwise until the random noise disappears. This state is known as the “squelch threshold.” 6.
10.4 SIMPLEX/DUPLEX CHANNEL USE Refer to the VHF MARINE CHANNEL CHART (page 89) for instructions on use of simplex and duplex channels. NOTE All channels are factory-programmed in accordance with International, Industry Canada (Canada), and FCC (USA) regulations. Mode of operation cannot be altered from simplex to duplex or vice-versa. 10.5 INTERNATIONAL, USA, AND CANADA MODE 1. To change the modes, hold the [16/9] key and press the [WX] key.
details). 3. The programmed NOAA weather channels will be scanned along with the regular-programmed channels. However, scanning will not stop on a normal weather broadcast unless a NOAA alert is received. 4. When an alert is received on a NOAA weather channel, scanning will stop and the transceiver will emit a loud beep to alert the user of a NOAA broadcast. 5. Press the [WX] key to stop the alert tone and receive the weather report.
10.8 CALLING ANOTHER VESSEL (CHANNEL 16 OR 9) Channel 16 may be used for initial contact (hailing) with another vessel. However, its most important use is for emergency and distress messages. This channel must be monitored at all times except when actually using another channel. It is monitored by the U.S. and Canadian Coast Guards and by other vessels. Use of channel 16 for hailing must be limited to initial contact only.
amples for USA use are Channels 24, 25, 26, 27, 28, 84, 85, 86, and 87. Call the marine operator and identify yourself by your vessel’s name, The marine operator will then ask you how you will pay for the call (telephone credit card, collect, etc.) and then link your radio transmission to the telephone lines. The marine telephone company managing the VHF channel you are using may charge a link-up fee in addition to the cost of the call. 10.
10.12 SCANNING Allows the user to select the scan type from Memory scan or Priority scan. “Memory scan” scans the channels that were programmed into memory. “Priority scan” scans the channels programmed in memory with the priority channel. 10.12.1 Selecting the Scan Type 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “SCAN Type” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4.
10.12.3 Priority Scanning (P-SCAN) In the default setting, Channel 16 is set as the priority channel. You may change the priority channel to the desired channel from the Channel 16 by the Radio Setup Mode, refer to section “12.6 PRIORITY CHANNEL SET.” 1. Adjust the SQL knob until background noise disappears. 2. Select a desired channel to be scanned using the CHANNEL selector knob.
10.13 PA/FOG OPERATION PA/FOG mode allows the transceiver to be used as a 30W hailer when an optional STANDARD HORIZON 220SW or 240SW PA horn speaker is installed. When in Hail mode the PA speaker Listen’s Back (acts as a microphone and amplifies sound to the front panel speaker) through the PA horn speaker which provides two-way communications through the PA horn speaker.
switch to activate the tone through the HAIL/PA speaker. Rotate the CHANNEL selector knob to control the AF output level. The AF output level can be set from 0 to 30 watts. 6. To exit the FOG HORN mode, press the [PA/FOG] or [CLR] key. 10.14 NAVIGATION INDICATION The transceiver has the ability to display Time, SOG, COG, as well as the position (LAT/LON), when connected to a GPS receiver. 1. Press and hold the [H/L(NAV)] key, display the position information on the LCD.
10.15.1 Communication 1. Press and hold the [DW(IC)] key, the mode is changed to “INTERCOM” mode. 2. If your GX3000S is equipped with two CMP25 RAM+ Mic’s (or VH-310 Handset), select the companion you wish to communicate (Ram1, Ram2, or ALL) with the CHANNEL selector knob, then press the [ENT] key. 3. When the “INTERCOM” is activated, “Intercom ” is displayed on the GX3000S, and “IC” is displayed on the CMP25 RAM+ Mic or VH-310 Handset. 4. Press the PTT switch.
10.16 VOICE SCRAMBLER If privacy of communications is desired, a CVS2500 voice scrambler (VS) can be installed in the transceiver. Contact your Dealer to have a CVS2500 installed. Refer to the section 12.11 VOICE SCRAMBLER to program the voice scrambler. 1. Turn on the transceiver. 2. Select a channel that was programmed for scrambler mode (“VS” will appear on the LCD).
11 DIGITAL SELECTIVE CALLING 11.1 GENERAL WARNING This radio is designed to generate a digital maritime distress and safety call to facilitate search and rescue. To be effective as a safety device, this equipment must be used only within communication range of a shorebased VHF marine channel 70 distress and safety watch system. The range of signal may vary but under normal conditions should be approximately 20 nautical miles. NOTE A DSC Warning sticker is included with the GX3000S.
11.2 MARITIME MOBILE SERVICE IDENTITY (MMSI) 11.2.1 What is an MMSI? An MMSI is a nine digit number used on Marine Transceivers capable of using Digital Selective Calling (DSC). This number is used like a telephone number to selectively call other vessels. THIS NUMBER MUST BE PROGRAMMED INTO THE RADIO TO OPERATE THE GX3000S DSC FUCTIONS. How can I obtain an MMSI assignment? Boat US offers online registration of a MMSI. Visit www.boatus.com/mmsi 11.2.
11.3 DSC DISTRESS CALL The GX3000S is capable of transmitting and receiving DSC Distress messages to all DSC radios. The GX3000S may be connected to a GPS to also transmit the Latitude, Longitude of the vessel. 11.3.1 Transmitting a DSC Distress Call NOTE To be able to transmit a DSC distress call an MMSI number must be programmed, refer to section “11.2.2 Programming the MMSI.” In order for your ships location to be transmitted a GPS must be connected to the GX3000S, refer to section “8.3 ACCESSORY CABLE.
Transmitting a DSC Distress Call with Nature of Distress The GX3000S is capable of transmitting a DSC Distress Call with the following “Nature of Distress” categories: Undesignated, Fire, Flooding, Collision, Grounding, Capsizing, Sinking, Adrift, Abandoning, Piracy, MOB 1. Lift the red spring loaded DISTRESS cover and press the [DISTRESS] key. The “DISTRESS” menu will appear on the LCD. 2. Turn the CHANNEL selector knob to select the desired nature of distress category. 3.
11.3.2 Receiving a DSC Distress Call 1. When a DSC Distress call is received, an emergency alarm sounds. Then channel 16 is automatically selected. 2. Press any key to stop the alarm. 3. Turn the CHANNEL selector knob to change the display to show the position of the vessel in distress. 4 If the position of the vessel distress data does not include position, the LCD will show the display on the right.
11.4.1 Transmitting an All Ships Call 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “All Ships.” 3. Press the [ENT] key. (To cancel, turn the CHANNEL selector knob to select “Exit.”) 4. Turn the CHANNEL selector knob to select the call (“Ugency” or “Safety”). 5. Press the [ENT] key to transmit the selected type of all ships DSC call. 6. After the ALL SHIPS CALL is transmitted, the transceiver will switch to CH16. 7.
11.5 INDIVIDUAL CALL This feature allows the GX3000S to contact another vessel with a DSC VHF radio and automatically switch the receiving radio to a desired communications channel. This feature is similar to calling a vessel on CH16 and requesting to go to another channel (switching to the channel is private between the two stations). 11.5.
11. If a mistake was made entering in the name or the MMSI number repeat pressing the [H/L(NAV)] key until the wrong character is selected, then move the channel knob to correct the entry. 12. To store the data entered, press and hold the [ENT] key. 13. To enter another individual address, repeat steps 4 through 12. 14. To exit this menu and return to radio operation mode press the [16/9] key. NOTE Selecting “Next” or “Exit” will automatically save the name and MMSI number into memory. 11.5.
11.5.3 Setting up the Individual/Group Call Ringer When a Individual Call or Group Call is received the radio will produce a ringing tone for 3 minutes. This selection allows the Individual Call ringer time to be changed. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appear. 2. Turn the CHANNEL selector knob to select “DSC Setup” menu. 3. Press the [ENT] key, then select “INDIV Ring” with the CHANNEL selector knob. 4. Press the [ENT] key. 5.
11.5.4 Transmitting an Individual Call This feature allows the user to contact another vessel with a DSC radio. This feature is similar to calling a vessel on CH16 and requesting to go to another channel. Pre-Programmable Calling 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “Individual.” (To cancel, select “Exit” with the CHANNEL selector knob or press the [16/9] key.) 3. Press the [ENT] key.
Manual Calling You may enter an MMSI number manually to contact without the Setting up the Individual Directory. 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “Individual.” (To cancel, select “Exit” with the CHANNEL selector knob or press the [16/9] key.) 3. Press the [ENT] key. The transceiver will beep, and the “Individual directory” will appear. 4. Turn the CHANNEL selector knob to select “Manual,” then press the [ENT] key. 5.
13. Press any key to listen to the channel to make sure it is not busy, then key the microphone and call the other vessel you desire to communicate with. 11.5.5 Receiving an Individual Call When the GX3000S receives a individual call, by default the GX3000S automatically transmits a acknowledgement before switching to the requested channel. The GX3000S can be set so the GX3000S prompts you to manually send a reply, refer to section “11.5.2 Setting up Individual Reply.” 1.
11.6.2 Reviewing Received Calls Logged into the Call Waiting Directory 1. Press the [CALL(MENU)] key. The “DSC Operation” 2. 3. 4. 5. 6. menu will appear. Turn the CHANNEL selector knob to select “DSC Log” menu. Press the [ENT] key, then turn the CHANNEL selector knob to select the category (“Distress” or “DSC Call”) you want to review and call back. Press the [ENT] key, then turn the CHANNEL selector knob to select the station (name or MMIS number) you want to review and call back.
11.7 GROUP CALL This feature allows the user to contact a group of specific vessels (example members of a yacht club) using DSC radios with Group call function to automatically switch to a desired channel for voice communications. 11.7.1 Setting up a Group Call For this function to operate the same Group MMSI must be programmed into all the DSC VHF radios within the group of vessels that will be using this feature.
11. If a mistake was made entering in the name or the MMSI number repeat pressing the [H/L(NAV)] key until the wrong character is selected, then move the channel knob to correct the entry. 12. To store the data entered, press and hold the [ENT] key. 13. To enter another individual address, repeat steps 4 through 12. 14. To exit this menu and return to radio operation mode press the [16/9] key. 11.7.2 Transmitting a Group Call Pre-Programmable Calling 1. Press the [CALL(MENU)] key.
Manual Calling You may enter a Group MMSI number manually to contact without the Setting up the Group call number. 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear. 2. Turn the CHANNEL selector knob to select “Group.” (To cancel, select “Exit” with the CHANNEL selector knob or press [16/9] key.) 3. Press the [ENT] key. The transceiver will beep, and the “Group Directory” will appear. 4. Turn the CHANNEL selector knob to select “Manual,” then press the [ENT] key. 5.
11.7.3 Receiving a Group Call 1. When a group call is received, the GX3000S will produce a ringing alarm sound. 2. The radio automatically switches to the requested channel. 3. Press any key to stop the alarm. 4. Monitor the channel for the person calling the Group for a message. 5. If you want to respond, monitor the channel to make sure it is clear, then press the PTT on the mic and talk to the calling ship(s).
11.8 POSITION REQUEST Advancements in DSC have made it possible to poll the location of another vessel and show the position of that vessel on the display of the GX3000S. Standard Horizon has taken this feature one step further, if any Standard Horizon GPS is connected to the GX3000S, the polled position of the vessel is shown on the display of the GPS chart plotter making it easy to navigate to the location of the polled vessel.
The GX3000S has the capability to turn off the Position Request ringer. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Turn the CHANNEL selector knob to select “DSC Setup” menu. 3. Press the [ENT] key, then select “DSC Beep” with the CHANNEL selector knob. 4. Press the [ENT] key. 5. Turn the CHANNEL selector knob to select “POS Request.” 6. Turn the CHANNEL selector knob to select “Off.” 7. Press the [ENT] key to store the selected setting. 8.
NOTE If the GX3000S does not receive position data from the polled vessel, the LCD will show “NO POSITION DATA.” Manual Request You may enter an MMSI number manually to contact without the Setting up the Individual / Position Call Directory. 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear in the display. 2. Turn the CHANNEL selector knob to select “POS Request.” 3. Press [ENT] key to show the Position request directory. This directory uses the INDIVIDUAL Directory information. 4.
11.8.3 Receiving a Position Request When a position request call is received from another vessel, a ringing alarm will sound and POS REQUEST will be shown in the LCD. Operation and transceiver function differs depending on “POS Reply” in the “DSC Setup” menu setting. Automatically reply: 1. When a position request call is received, a calling alarm sounds 4 times. Then requested position coordinates are transmitted automatically to the vessel requesting your vessels position. 2.
11.9 POSITION SEND The feature is similar to Position Request, however instead of requesting a position of another vessel this function allows you to send your position to another vessel. Your vessel must have an operating GPS receiver connected for the GX3000S to send the position. 11.9.1 Setting up a Position Send Ringer The GX3000S has the capability to turn off the Position Send ringer. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2.
Manual Calling 1. Press the [CALL(MENU)] key. The “DSC Operation” menu will appear in the display. 2. Turn the CHANNEL selector knob to select the “POS Send.” 3. Press [ENT] key to show the Position Send directory. This directory uses the INDIVIDUAL Directory information. 4. Turn the CHANNEL selector knob to select “Manual,” then press the [ENT] key. 5. Enter the MMSI number (nine digits) which you want to contact, then press the [ENT] key. 6.
11.10 MANUAL INPUTTING GPS LOCATION (LAT/LON) You may send the Latitude/Longitude of your vessel manually even if the GX3000S is not connected the GPS receiver unit. After the position is entered, transmitting a DSC Distress, Position Request, or Position Send will contain the manually entered position. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Turn the CHANNEL selector knob to select “DSC Setup” menu. 3.
12 RADIO SETUP NOTE The optional CMP25 RAM+ mic and VH-310 Handset can also change the RADIO SETUP menu. Refer to page 68 (RAM+ mic) and page 74 (VH-310) for details. 12.1 LAMP ADJUSTING Allows setting up the backlight intensity or to turn it off. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Dimmer” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4.
12.3 TIME OFFSET From the Factory the GX3000S shows GPS satellite time or UTC time. A time offset is needed to show the local time in your area. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Time Set” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select time offset from UTC. See illustration below to find your offset time from UTC.
12.4 TIME LOCATION This selection selects the time display between local time and UTC (time GPS sends to radio). Time is displayed when GPS position (LAT/LON) is displayed by press and holding the [H/L(NAV)] key. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Time Disp.” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select “UTC” or “Local.” 5.
12.6 PRIORITY CHANNEL SET Allows selection of the priority channel when priority scan is enabled. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Priority CH” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the channel to be a priority. 5. Press the [ENT] key to store the selected setting. 6.
12.8 SCAN RESUME TIME This selection is used to select the time the GX3000S waits after a transmission ends before starting scanning. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “SCAN Resume” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the desired resume time. The resume time can be set to “1sec,” “2sec,” “3sec,” or “Off.
12.10 WX ALERT This selection allows the radios NOAA Weather alert to be turned off. Default setting is ON. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “WX Alert” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the desired WX alert mode. The WX alert mode can be set to “On SCAN,” “On WX,” “On SCAN/WX,” or “Off.” 5.
12.12 CHANNEL NAME CHANGE This selection allows you to customize the name of a channel from the default name. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “CH Name” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select the channel to be named, then press the [ENT] key. 5. Turn the CHANNEL selector knob to scroll through the first letter of the channel name. 6.
12.13 NAMING THE RADIO OR SECOND STATION MIC OR HANDSET This function allows you to change the name of the RADIO or second station microphones. Example: “RADIO - CABIN,” “RAM1 - HELM,” “RAM2 FLYBRIDGE.” 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “Unit Name” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4.
12.14 FOG ALERT TONE FREQUENCY This selection allows you to select the Alert Tone Frequency for the PA/FOG Operation. Available selections are “200 Hz” through “850 Hz” in 50 Hz steps. The default Alert Tone Frequency is 400 Hz. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ENT] key, then select “FOG Freq.” in the “Radio Setup” menu with the CHANNEL selector knob. 3. Press the [ENT] key. 4. Turn the CHANNEL selector knob to select desired tone frequency. 5.
13 ENHANCED RAM+ MIC OPERATION When the RAM+ microphone is connected to the GX3000S, most VHF, DSC, and setup menus can be remotely operated. The RAM+ Mic is supplied with 23 feet (7 m) of routing cable and can be extended up to 70 feet (21 m) using three 23 feet extension cables model CT-100. The intercom operation can be used between the RAM+ Mic and the transceiver. 13.1 RAM+ MIC CONTROLS IC DW CALL SET NAV MENU WX U.I.C MEM SCAN 16 9 SQUELCH CONTROL (SQL) Activates the squelch adjusting mode.
POWER SWITCH (PWR) Press and hold down this key to turn to the transceiver and RAM+ Mic on and off. PTT (Push-To-Talk) SWITCH Activates transmission. [H/L] KEY Toggles between high and low power. When the [H/L] key is pressed while the transceiver is on channel 13 or 67, the power will temporarily switch from LO to HI power until the PTT is released. The [H/L] key does not function on transmit inhibited and low power only channels.
[DW] Key Watches for a transmission on CH16 and another selected channel until either signal is received. (Dual watch) Secondary use Press and hold [DW] key, intercom operation will operate between radio and RAM+ Mic. [NAV] Key Press this key, when connected to the GPS receiver, the LCD displays Position Data and Time from the GPS. [WX] Key Immediately recalls the previously selected US NOAA weather channel from any channel location.
13.2.2 Operating the FOG Horn The GX3000S is capable of sending Underway, Stop, Sail, Tow, Horn, Siren, Aground and Anchor signals. 1. Press and hold the [NAV] key then select “FOG” with the [ ] or [ ] key. 2. Press the [CALL/SET] key. 3. Select the one of the eight functions described above with the [ ] or [ ] key and press the [CALL/SET] key. 4. On the “Horn” and “Siren” modes, press the PTT switch to activate the tone through the HAIL/PA speaker.
13.4 DSC/RADIO SETUP MODE The RAM+ can access the DSC / RADIO setup menu (refer to section “11 DIGITAL SELECTIVE CALLING” and section “12 RADIO SETUP MODE” for details). The LAMP, CONTRAST, and KEY BEEP menu item accessed from the RAM+ only controls the RAM+’s display and speaker. DSC/RADIO Setup mode from the RAM+: 1. Press and hold down the [CALL/SET] key until “RADIO SETUP” menu appears. 2. Press the [ ]/[ ] key to select “RADIO SETUP” or “DSC SETUP” menu. 3.
MEMO GX3000S Page 73
14 VH-310 HANDSET OPERATION When the VH-310 HANDSET is connected to the GX3000S, most VHF, DSC, and setup menus can be remotely operated. The VH-310 HANDSET is supplied with 23 feet (7 m) of routing cable and can be extended up to 70 feet (21 m) using three 23 feet extension cables model CT-100. The intercom operation can be used between the VH-310 HANDSET or the GX3000S. 14.1 VH-310 HANDSET CONTROLS PWR key Press and hold down this key to turn to the transceiver and VH-310 HANDSET on and off.
[SQL] key Activates the squelch adjusting mode. Press this key to activate the squelch adjusting mode. Press the [ ] or [ ] key to adjust the squelch. [CALL(MENU)] key The [CALL(MENU)] key functions as the enter key. Secondary use Press the [CALL(MENU)] key to access the DSC OPERATION menu. The “INDIVIDUAL CALL,” “GROUP CALL,” “ALL SHIP CALL,” “POSITION REQUEST,” POSITION SEND,” STANDBY MODE,” and “CALL WAITING” functions can be accessed from the DSC OPERATION menu.
KEYPAD [1(DIM)] key When in radio mode, this key is used to directly select channel digit “1” in a channel number. Secondary use Press the [F] key first then press the [1(DIM)] key to access the LCD Dimmer menu. Refer to section “12.1 LAMP ADJUSTING” for details. [2(MEM)] Key When in radio mode, this key is used to directly select channel digit “2” in a channel number.
[6(NAV)] Key When in radio mode, this key is used to directly select channel digit “6” in a channel number. Secondary use Press the [F] key first then press the [6(NAV)] key, the LCD will display NAV GPS Data, Time, SOG (Speed Over Ground), and COG (Course Over Ground) when a GPS is connected to the accessory cable of the GX3000S. See section “8.3 ACCESSORY CABLE” for details. [7(SCRM)] Key When in radio mode, this key is used to directly select channel digit “7” in a channel number.
14.2 PA/FOG OPERATION The VH-310 Handset is capable of controlling the 30W Public address, 4 fog horns, bells and whistles. 14.2.1 Operating the PA / Hailer 1. Press the [F] key followed by the [8(PA)] key, activate the “PA / HAIL” mode. 2. Press the PTT switch and speak into the microphone. 3. To turn up the PA Volume, press the PTT switch and press the [ ] or [ ] keys to adjust the Audio output level. The level can be set from 0 to 30W. 4.
14.3 INTERCOM OPERATION 14.3.1 Communication 1. Press the [F] key followed by the [5(IC)] key, the mode is changed to “INTERCOM” mode. 2. When the “INTERCOM” operation is activated, “IC” is displayed on the VH-310 Handset (and RAM+ Mic, if used) and “INTERCOM” is displayed on the GX3000S. 3. Press the PTT switch, “TALK” is displayed. NOTE: A warning beep is emitted when the RAM+ Mic PTT switch is pressed while the transceiver microphone’s PTT switch is pressed. 4.
14.4 MANUAL INPUTTING OF THE GPS LOCATION (LAT/LON) You may send the Latitude/Longitude of your vessel manually from the VH-310 Handset even if the GX3000S is not connected the GPS receiver unit. After the position is entered, transmitting a DSC Distress, Position Request, or Position Send will contain the manually entered position. 1. Press and hold down the [CALL(MENU)] key until “Radio Setup” menu appears. 2. Press the [ ] key to select “DSC SETUP” menu. 3.
14.5 DSC/RADIO SETUP MODE The VH-310 Handset can access the DSC / RADIO setup menu (refer to section “11 DIGITAL SELECTIVE CALLING” and section “12 RADIO SETUP MODE” for details). The CONTRAST, NAV DISPLAY, KEY BEEP, and AF SELECT menu item accessed from the VH-310 Handset only controls the VH-310 Handset’s display and speaker. DSC/RADIO Setup mode from the VH-310 Handset: 1. Press and hold down the [CALL(MENU)] key until “RADIO SETUP” menu appears. 2.
14.5.1 Changing GPS Information to Vessel position or COG Allows customizing the NAV data showing GPS Information. Factory default is “Your Vessel’s Current Position,” however, following the steps below the GPS Information can be changed to “Course Over Ground (COG).” 1. Press and hold down the [CALL(MENU)] key until “RADIO SETUP” menu appears. 2. Press the [ENT] key, then select “NAV DISPLAY” with the [ ]/[ ] key. 3. Press the [CALL(SET)MENU] key. 4.
MEMO GX3000S Page 83
15 MAINTENANCE The inherent quality of the solid-state components used in this transceiver will provide many years of continuous use. Taking the following precautions will prevent damage to the transceiver. • • • • Keep the microphone connected or the jack covered at all times to prevent corrosion of electrical contacts; Never key the microphone unless an antenna or suitable dummy load is connected to the transceiver.
15.2 FACTORY SERVICE In the unlikely event that the radio fails to perform or needs servicing, please contact the following: Standard Horizon Attention Marine Repair Department 10900 Walker Street, Cypress, CA 90630 Telephone (800) 366-4566 An “RA” Return Authorization number is not necessary to send a product in for service. Include a brief note describing the problem along with your name, return address, phone number, and proof of purchase.
15.3 TROUBLESHOOTING CHART SYMPTOM PROBABLE CAUSE REMEDY Transceiver fails to power up. No DC voltage to the a. Check the 12VDC battery connections and transceiver, or blown the fuse. fuse. b. The PWR key needs to be pressed and held to turn the radio on. Transceiver blows fuse when connected to power supply. Reversed power wires. Check the power cable for DC voltage, or replace the fuse (6A 250V).
MEMO GX3000S Page 87
16 CHANNEL ASSIGNMENTS Tables on the following columns list the VHF Marine Channel assignments for U.S.A. and International use. Below are listed some data about the charts. 1. VTS. Where indicated, these channels are part of the U.S. Coast Guard’s Vessel Traffic System. 2. Alpha channel numbers, that is, channel numbers followed by the letter A (such as Channel 07A) are simplex channels on the U.S.A. or Canadian channel assignments whose counterparts in the International assignments are duplex channels.
6. Marine vessels equipped with VHF radios are required to monitor Channel 16. CH 01 01A 02 03 03A 04 U C X X X X X 04A X 05 05A 06 07 X X X X 07A 08 09 X X X X X X 10 11 12 13 14 15 15 16 17 18 18A 19 19A 19A 20 X X X X X X X X X X X 20A 21 21A 22 22A X X X X X X X X X X X X X X X X GX3000S VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 156.050 160.650 Public Correspondence (Marine Operator) S 156.050 Port Operation and Commercial. VTS in selected areas X D 156.100 160.
CH 23 23A 24 25 26 27 28 60 61 U 61A X X X X X X X C X X X X X X X X 62 62A X 63 63A X 64 64A X X X 65A 66 X X 66A 67 X X X X 68 69 X X X X 70 X X 71 X X 72 73 X X X X 74 X X 65 Page 90 VHF MARINE CHANNEL CHART I S/D TX RX CHANNEL USE X D 157.150 161.750 Public Correspondence (Marine Operator) S 157.150 U.S. Government Only X D 157.200 161.800 Public Correspondence (Marine Operator) X D 157.250 161.850 Public Correspondence (Marine Operator) X D 157.300 161.
CH 75 76 77 77 78 U X X X C 78A 79 79A 80 80A 81 81A X X X X X X X X 82A X X 83 83A X X X 83 84 85 86 87 88 88A WX01 WX02 WX03 WX04 WX05 WX06 WX07 WX08 WX09 WX10 X X X X X X X X X X X X X X X X X 82 X X X X X X X X X X X X X X X X VHF MARINE CHANNEL CHART S/D TX RX CHANNEL USE S 156.775 Port Operations (Inter-ship only) (1W) S 156.825 Port Operations (Inter-ship only) (1W) S 156.875 Port Operations (Inter-ship only) (1W) X S 156.875 Port Operations (Inter-ship only) X D 156.925 161.
Points of communication (Intership and between coast and ship Coast u n l e s s o t h e r w i s e Ship transmit transmit iandicated) Port Operations 01A1 156.050 156.050 63A1 156.175 156.175 052 156.250 156.250 65A 156.275 156.275 66A 156.325 156.325 123 156.600 156.600 73 156.675 156.675 3 14 156.700 156.700 74 156.725 156.725 156.875 Intership only. 774 20A12 157.000 Intership only. Navigational (Bridge-to-Bridge)5 136 156.650 156.650 677 156.375 156.375 Commercial 01A1 156.050 156.050 63A1 156.175 156.
4: Use of 156.875 MHz is limited to communications with pilots regarding the movement and docking of ships. Normal output power must not exceed 1 watt. 5: 156.375 MHz and 156.650 MHz are available primarily for intership navigational communications. These frequencies are available between coast and ship on a secondary basis when used on or in the vicinity of locks or drawbridges. Normal output power must not exceed 1 watt.
17 WARRANTY Marine Products Limited Warranty STANDARD HORIZON (a division of Vertex Standard) warrants, to the original purchaser only, each new Marine Communications Product (“Product”) manufactured and/or supplied by STANDARD HORIZON against defects in materials and workmanship under normal use and service for a period of time from the date of purchase as follows: Fixed Mount and Portable Transceivers 1 year - if purchased before 01/01/91 3 years - if purchased between 01/01/91 and 01/01/94 3 years Waterp
STANDARD HORIZON will not warrant installation, maintenance or service of the Products. In all instances, STANDARD HORIZON’s liability for damages shall not exceed the purchase price of the defective Product. This warranty only extends to Products sold within the 50 States of the United States of America and the District of Columbia.
ONLY PRODUCTS SOLD ON OR AFTER JANUARY 1, 1991 ARE COVERED UNDER THE TERMS OF THIS LIMITED WARRANTY. ON-LINE WARRANTY REGISTRATION THANK YOU for buying Marine Division of Vertex Standard products! We are confident your new radio will serve your needs for many years! Please visit www.standardhorizon.com to register the GX3000S Marine VHF. It should be noted that visiting the Web site from time to time may be beneficial to you, as new products are released they will appear on the STANDARD HORIZON Web site.
18 SPECIFICATIONS Performance specifications are nominal, unless otherwise indicated, and are subject to change without notice. 18.1 GENERAL Channels ............................................................. All USA, International and Canadian Input Voltage ....................................................................................... 13.8 VDC ±20% Current Drain Standby ........................................................................................................... 0.5 A Receive ....
19 APPENDIX FOG HORN TIMING CHART The fog horn function sounds a horn repeatedly until the function is turned off. TYPE UNDERWAY PATTERN One 5-second blasts evey 120 seconds. USAGE Motor vessel underway and making way. Listen Back 120s STOP Two 5-second blasts (separated by 2 seconds) evey 120 seconds. 5s Motor vessel underway but stopped (not making way). 5s Listen Back 2s SAIL 120s 2s One 5-second blasts followed by two 1second blasts (separated by 2 seconds) evey 120 seconds.
MEMO GX3000S Page 99
Marine Division of VERTEX STANDARD US Headquarters 10900 Walker Street, Cypress, CA 90630, U.S.A. www.standardhorizon.com E M 0 Page 100 1 4 N 1 0 Copyright 2006 VERTEX STANDARD CO., LTD. All rights reserved. No portion of this manual may be reproduced without the permission of VERTEX STANDARD CO., LTD.
