Instructions / Assembly

ManualsBrandsStanley Doors ManualsDoors & Windows32 in. x 80 in. Geometric Zinc 1/2 Lite 1-Panel Prefinished White Right-Hand Inswing Steel Prehung Front Door

DOOR INSTALLATION INSTRUCTIONS

Required Tools and Materials

• Level(forsub-sillonly)

• Shims

• Hammer

• Drill

• #2FlatandPhilipsScrewDriver

• Low-expansionfoam(orberglass)insulation

+ Important Point: Although all steps are critical, this symbol identies

procedures requiring extra attention.

Check Your Work:Thissymbolidentieswhentheworkshouldbechecked

 forcorrectnessbeforecontinuingwithinstallation.

Ensurethefollowingconditionsaremet:

• Theroughopeningisideally1”widerand½”tallerthantheoutsideframedimensions

 ofthedoorsystem.

• TheROisplumb,squareandlevel

• Theoldframehasbeencompletelyremovedinretrotinstallation

• Theexistingsub-sillisatleast6”deepfor45/8”framesandatleast83/4”deep

 for7¼”frames.

+ Becauseasolid,levelsub-sillisabsolutelyessentialforproperdoorsysteminstallation,

 donotproceedwiththeuntilthesub-sillisbothsolidandlevel.

Standontheoutsideofthedoorway.Withthedoorfacingout,tiltthedoorbacktowardthe

outside.PlacethesillintheROandtiltthedoorupandintotheopening.

+ Do not leave the door wide open during installation.

The weight of the door may cause it to fall and cause injury.

Applythree¼”linesofcaulk(acryliccaulkisrecommended)alongthelengthofthesub-sill,

therstlinestartingapproximately1”fromtheinsideedge.Thelinesshouldbeabout1”apart.

Removethetopscrewfromeachhinge.

Withthedoorclosedandfromtheinsideshimdirectlybehindthevacanthingescrewholein

eachhinge,untilthereisaconsistent1/8”gapbetweenthehinge-sidejambandthedoorslab

edgealongtheentireheightofthedoor.Thereshouldbea1/8”gapbetweenthelatch-side

jambandthedoorslabedgeatthetopandbottomofthedooronly.Drivea3”installation

screwthroughthevacantholeineachhinge,throughthejamb,shimsandintothestud.

 Fromtheoutsideandwiththedoorclosed,ensurethattheframe

isinastraight vertical plane (nottwisted).To dothischeckthat the

weather-stripping on the latch side is evenly compressed along the

entireheightofthedoorslabwithoutanypinchingorgaps.

Standontheinsideofthedoorandcenterthedoorintheopening.Shimtightlyatthebottom

cornersofthedoorunit.Thiswillkeepthedoorcenteredandtheframetightagainstthesill.

Shimthetopofthedooronthelatchside.Installshimsuntilthereisaconsistent1/8”gap

betweenthetopofthedoorslabandtheframeheader.

Shimthehingesideoftheframe.Thiswillholdthedoortightinitspositionrelativetothe

frame.Thedoorshouldoperatefreelywithnothingbutshimsholdingitinplace.

Removeallpackagingmaterialssuchasnails,staplesandscrews

 Makesurethedoorswingsfreelyintheframe.

STEP 1: PREPARE ROUGH OPENING

STEP 4: PLACE DOOR IN ROUGH OPENING

STEP 5: SHIM AND FASTEN

STEP 2: CAULK THE SUB-SILL

STEP 3: REMOVE PACKAGING MATERIALS

DOORS

Summary of content (2 pages)

PAGE 1
DOORS DOOR INSTALLATION INSTRUCTIONS Required Tools and Materials • Level (for sub-sill only) • Shims • Hammer • Drill • #2 Flat and Philips Screw Driver • Low-expansion foam (or fiberglass) insulation + Important Point: Although all steps are critical, this symbol identifies procedures requiring extra attention. C Check Your Work: This symbol identifies when the work should be checked for correctness before continuing with installation.
PAGE 2
C When the shims are properly installed, the frame should not move or twist at all when the screws are tightened and counter-sunk thereby maintaining the 1/8”gap. If there is any movement, loosen the screws and shim tighter to maintain the 1/8”gap, and then re-tighten the screws. STEP 7: INSULATE Score the shims with a utility knife and then snap where scored. Trim any excess. Insulate around the top and the side of the door unit in the cavity between the frame and the wall studs.