Use and Care Manual

Red (flashing rapidly): The battery of the unit is overheated (due to extensive use or recharging),
or is too cold (the ambient temperature has dropped below -20°C). Operation will stop at this stage.
CHARGING/RECHARGING THE SPOTLIGHT
This unit is shipped in a partially charged state. Charge unit after purchase and BEFORE first use
until the battery/charge status LED indicator lights green.
Recharge after each use until the battery/charge status LED indicator lights green.
IMPORTANT: When the unit is not in use, we recommend that the battery is charged at least
every 3 to 6 months.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• Make sure the unit is thoroughly dry before charging or recharging. If the unit has been
submerged, wipe it dry with a soft cloth before opening the end cap. If water leaks into the
charging port, the unit can sustain permanent damage.
• Never place the light face down on any surface when charging.
• Failure to keep the battery charged will cause permanent damage and result in poor performance.
Charging/recharging using the 120V AC/USB Charging Adapter
1. Make sure the spotlight is off.
2. Unscrew (counterclockwise) the waterproof end cap on the back of the unit and remove it.
3. Insert the micro-USB plug of the USB charging cable into the micro-USB charging port on the
back of the spotlight.
4. Insert the regular USB plug of the USB charging cable into the 120V AC/USB charging adapter.
5. Plug the 120V AC/USB charging adapter into a (powered) standard North American 120 volt
60Hz outlet. The battery/charge status LED indicator will light or flash in one of three colors
(as described in the “Reading the Battery/Charge Status LED Indicator” section) to indicate the
charging status.
6. Charge up to 5 hours or until the battery/charge status LED indicator lights green.
7. When charging is complete, first unplug the 120V AC/USB charging adapter from the power
source, then disconnect the USB charging cable from the adapter and the spotlight. Store the
adapter and cable in a safe place.
8. Replace the end cap on the unit, screwing clockwise until the triangular arrow on the end
cap is pointing to the dot icon on the rear of unit. Make sure it fits securely, but do NOT
overtighten.
Charging/recharging using the 12V DC/USB Charging Adapter
1. Make sure the spotlight is off.
2. Unscrew (counterclockwise) the waterproof end cap on the back of the unit and remove it.
3. Insert the micro-USB plug of the USB charging cable into the micro-USB charging port on the
back of the spotlight.
4. Insert the regular USB plug of the USB charging cable into the 12V DC/USB charging adapter.
5. Insert the 12 volt DC/USB charging adapter into the 12 volt DC accessory outlet of a vehicle
or other functioning 12 volt DC power source. The LED indicator on the 12V DC/USB charging
adapter will light green when it is properly plugged into the 12 volt DC power source. The
battery/charge status LED indicator will light or flash in one of three colors (as described in the
“Reading the Battery/Charge Status LED Indicator” section) to indicate the charging status.
Note: Some vehicles require that the ignition be switched to the accessory position in order to power
the accessory outlet.
6. Charge until the battery/charge status LED indicator lights green.
7. When charging is complete, first unplug the 12V DC/USB charging adapter from the 12 volt
DC power source, then disconnect the USB charging cable from the adapter and the spotlight.
Store the adapter and cable in a safe place.
8. Replace the end cap on the unit, screwing clockwise until the triangular arrow on the end
cap is pointing to the dot icon on the rear of unit. Make sure it fits securely, but do NOT
overtighten.
Charging/recharging using the USB charging cable and a device
with a USB power port (not supplied)
1. Make sure the spotlight is off.
2. Unscrew (counterclockwise) the waterproof end cap on the back of the unit and remove it.
3. Insert the micro-USB plug of the USB charging cable into the micro USB charging port on the
back of spotlight.
4. Insert the regular USB plug of the USB charging cable into a device’s functional USB power
port. The battery/charge status LED indicator will light or flash in one of three colours (as
described in the “Reading the Battery/Charge Status LED Indicator” section) to indicate the
charging status.
5. Charge until the battery/charge status LED indicator lights green.
6. When charging is complete, disconnect the USB charging cable from the device’s USB power
port and the spotlight. Store the cable in a safe place.
7. Replace the end cap on the unit, screwing clockwise until the triangular arrow on the end
cap is pointing to the dot icon on the rear of unit. Make sure it fits securely, but do NOT
overtighten.
OPERATING THE SPOTLIGHT
The On/Off Trigger turns the unit on and off, and is also used to choose either the high or low
brightness setting.
CAUTION: DO NOT OPERATE WHILE CHARGING.
Disconnect the charging cable or adapter, then select the light mode as follows:
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again within 5 seconds to use the spotlight in its low (dimmest) setting.
• Press the On/Off trigger a third time to turn the unit off.
or
• Press the On/Off trigger once to use the spotlight in its high (brightest) setting.
• Press the On/Off trigger again after 5 seconds to turn the unit off.
Note: The battery/charge status LED indicator will light in one of three colors (as described in the “Reading
the Battery/Charge Status LED” section) to indicate the battery status. It is visible through the
translucent waterproof end cap.
OPERATING THE 120 VOLT AC/USB CHARGING ADAPTER’S
USB PORT
Plug the 120 volt AC/USB charging adapter into a (powered) standard North American 120 volt
60Hz outlet. Then simply plug the USB device into the USB outlet and operate normally.
OPERATING THE 12 VOLT DC/USB CHARGING ADAPTER’S
USB POWER PORT
Plug the 12V DC/USB charging adapter into a vehicle’s 12 volt DC accessory outlet or other
functioning 12 volt DC power source. The LED indicator on the 12V DC/USB charging adapter will
light green to indicate that it is properly connected. Then simply plug the USB device into the USB
outlet and operate normally.
Note: Some vehicles require that the ignition be switched to the accessory outlet position in order to power
the accessory outlet
CARE AND MAINTENANCE
All batteries lose energy from self-discharge over time and more rapidly at higher temperatures.
When the unit is not in use, we recommend that the battery is charged at least every 3 to 6
months.
If the unit gets dirty, gently clean the outer surfaces of the spotlight unit with a soft cloth
moistened with a mild solution of water and detergent.
Except for the fuse in the 12 volt DC/USB charging adapter, there are no user-replaceable parts.
Periodically inspect the condition of adapters, connectors and wires. Contact manufacturer to
replace any components that have become worn or broken.
Battery replacement/disposal
BATTERY REPLACEMENT
The battery should last the service life of the unit. Service life is dependent on a number of factors
including but not limited to the number of recharge cycles, and proper care and maintenance of
the battery by the end user. Contact manufacturer for any information you may need.
SAFE BATTERY DISPOSAL
Contains a lithium-ion battery, which must be disposed of
properly. Recycling is required. Failure to comply with local,
state and federal regulations can result in fines, or imprisonment.
Please recycle.
WARNINGS:
• Do not dispose of the battery in fire as this may result in an explosion.
• Before disposing of the battery, protect exposed terminals with heavy-duty electrical tape to
prevent shorting (shorting can result in injury or fire).
• Do not expose battery to fire or intense heat as it may explode.
Replacing the Fuse in the 12V DC/USB Charging Adapter
2A FUSE
CENTER CONTACT
END CAP
1. Unscrew the end cap counterclockwise and
remove.
2. Remove center contact and fuse.
3. Check fuse with a continuity checker.
4. If blown, locate a replacement 2 amp fuse.
5. Replace the fuse, center contact and end
cap.
6. Screw end cap clockwise until it is finger
tight - DO NOT OVER-TIGHTEN.
7. Test for proper operation of the 12 volt DC/
USB charging adapter.
TROUBLESHOOTING
The spotlight will not charge
• Check that the spotlight is turned off.
• Check that the USB charging cable is properly connected to either the 12V DC/USB charging
adapter or the 120V AC/USB charging adapter, and to the spotlight.
• Check the connection to the AC or DC power source. Make sure there is good contact.
• Confirm that there is functioning AC or DC current.
• Check the plug fuse in the 12V DC/USB charging adapter. Replace the fuse following the instructions
in this manual, if necessary.
• The unit may have shut down to protect the battery from overheating after a long period of
operation or charging. Unplug the charging adapter from the power source and disconnect the
USB charging cable from the spotlight. Allow the spotlight to cool down for a period before
resuming charging.
The spotlight will not operate
• Make sure the On/Off Trigger has been pressed to turn the spotlight on.
• The internal battery may be completely discharged. Charge the unit following the directions given
in this manual.
• The unit may have shut down to protect the battery from overheating after a long period of
operation or charging; or the ambient temperature has dropped below –20°C. Allow the spotlight
to cool down or warm up for a period before resuming operation.
• If the ambient temperature is too hot or too cold the spotlight will not operate.
The 120V AC/USB charging adapter’s USB port will not operate
• Make sure you have live AC power to the outlet the 120V AC/USB charging adapter is plugged into.
• Make sure the rating of equipment plugged into the charging adapter’s USB port does not exceed
1A continuous.
• Some household USB-powered electronics will not operate with this USB port. Check the manual
of the corresponding electronic device to confirm that it can be used with this type of USB port.
The 12V DC/USB charging adapter’s USB port will not operate / LED indicator on the 12V DC/
USB charging adapter does not come on
• Check the connection to the 12 volt DC power source. Make sure there is good contact.
• Confirm there is functioning DC current.
• Check the plug fuse in the 12V DC/USB charging adapter. Replace the fuse following the
instructions in this manual, if necessary.
• Make sure the rating of equipment plugged into the charging adapter’s USB port does not exceed
2.1A continuous.
• Some household USB-powered electronics will not operate with this USB port. Check the manual
of the corresponding electronic device to confirm that it can be used with this type of USB port.
If the unit does not charge or operate after taking the steps given above, contact the manufacturer
at [phone].
ACCESSORIES
Recommended accessories for use with your tool may be available from the manufacturer. If you
need assistance regarding accessories, please contact the manufacturer at [phone].
WARNING: The use of any accessory not recommended for use with this appliance could be
hazardous.
SERVICE INFORMATION
Whether you need technical advice, repair, or genuine factory replacement parts, contact the
manufacturer at [phone].
ONE-YEAR LIMITED WARRANTY
The manufacturer warrants this product against defects in materials and workmanship for a period
of ONE (1) YEAR from the date of retail purchase by the original end-user purchaser (“Warranty
Period”).
If there is a defect and a valid claim is received within the Warranty Period, the defective product
can be replaced or repaired in the following ways: (1) Return the product to the manufacturer
for repair or replacement at manufacturer’s option. Proof of purchase may be required by
manufacturer. (2) Return the product to the retailer where product was purchased for an exchange
(provided that the store is a participating retailer). Returns to retailer should be made within the
time period of the retailer’s return policy for exchanges only (usually 30 to 90 days after the sale).
Proof of purchase may be required. Please check with the retailer for their specific return policy
regarding returns that are beyond the time set for exchanges.
This warranty does not apply to accessories, bulbs, fuses and batteries; defects resulting from
normal wear and tear, accidents; damages sustained during shipping; alterations; unauthorized
use or repair; neglect, misuse, abuse; and failure to follow instructions for care and maintenance
for the product.
This warranty gives you, the original retail purchaser, specific legal rights and you may have other
rights which vary from state to state or province to province. This product is not intended for
commercial use.
Please complete the Product Registration Card and return within 30 days from purchase of the
product to: Baccus Global LLC, One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL
33432. Baccus Global LLC, toll-free number: [phone].
SPECIFICATIONS
Light (Conforms to UL STD. 73)
Bulb: 5 watt LED bulb
Battery: Lithium-Ion, 3.6 V DC
Input: 5V DC, 1A (120 Volt AC/USB Charging Adapter) or
2.1A (12 Volt DC/USB Charging Adapter)
120V AC/USB Charging Adapter (Conforms to UL STD. 62368-1)
(Optional Accessory)
Input: 120V AC, 60Hz, 6.7W
Output: 5V DC, 1A
12V DC/USB Charging Adapter (Conforms to UL STD. 2089) (Optional Accessory)
Input: 12V DC, 1.1A
Output: 5V DC, 2.1A
Fuse: 2A
To purchase optional accessories, contact the manufacturer at [phone].
Imported by Baccus Global LLC,
One City Centre, 1 North Federal Highway, Suite 200, Boca Raton, FL 33432
www.Baccusglobal.com 1-877-571-2391
RD060917
LITHIUM-ION RECHARGEABLE
WATERPROOF LED SPOTLIGHT
INSTRUCTION MANUAL
FL5W10
SAVE THIS INSTRUCTION MANUAL FOR FUTURE
REFERENCE.
Copyright © 2017
Baccus Global LLC, Boca Raton, FL 33432
[phone]
3
4
5
6
8
7
2
1
9
10
11
12
14
13
15
16
Optional 120V AC/USB Charging Adapter: This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is
no guarantee that interference will not occur in a particular installation. If equipment does
cause harmful interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
• Consult the dealer or an experienced radio/TV technician for help.
Changes or modifications not approved by the party responsible for compliance could void
user’s authority to operate the equipment.
SAFETY GUIDELINES / DEFINITIONS
DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death
or serious injury.
WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in
death or serious injury.
CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor
or moderate injury.
CAUTION: Used without the safety alert symbol indicates potentially hazardous situation which, if
not avoided, may result in property damage.
RISK OF UNSAFE OPERATION. When using tools or equipment, basic safety precautions should
always be followed to reduce the risk of personal injury. Improper operation, maintenance or
modification of tools or equipment could result in serious injury and property damage. There
are certain applications for which tools and equipment are designed. Manufacturer strongly
recommends that this product NOT be modified and/or used for any application other than for
which it was designed. Read and understand all warnings and operating instructions before using
any tool or equipment.
IMPORTANT SAFETY INSTRUCTIONS
WARNING: This product or its power cord contains lead, a chemical known to the State of
California to cause cancer and birth defect or other reproductive harm. Wash hands after handling.
GENERAL SAFETY WARNINGS AND
INSTRUCTIONS
READ ALL INSTRUCTIONS
WARNING: Read all instructions before operating the spotlight. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
INSTRUCTIONS PERTAINING TO RISK OF FIRE, ELECTRIC
SHOCK, OR INJURY TO PERSONS
WARNING: RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO PERSONS –
WHEN USING ELECTRICAL APPLIANCES, BASIC PRECAUTIONS SHOULD ALWAYS BE FOLLOWED,
INCLUDING THE FOLLOWING:
• LED gets HOT quickly!
• Do not touch the LED at any time when operating.
• Only contact trigger when turning on.
• Do not touch hot lens or enclosure.
• Do not remain in light if skin feels warm.
• Do not operate the spotlight with a missing or damaged lens or enclosure.
• The spotlight and the supplied charging adapters are not toys and cannot be played with as toys.
To reduce the risk of injury, close supervision is necessary when these units are used near children.
• Use only attachments recommended or sold by the manufacturer.
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK:
• Use only the chargers supplied by the manufacturer to charge and recharge.
• When an extension cord is used:
– The marked rating of the detachable power supply cord or extension cord should be at least
as great as the electrical rating of this appliance.
– The cord should be arranged so that it will not drape over the countertop or tabletop where
it can be tripped over, snagged, or pulled on unintentionally (especially by children).
– The extension cord should be kept dry and off the ground.
• Do not store the unit or chargers outdoors.
• Charge indoors only. Do not expose chargers to water or any other liquid
WARNING: FIRE HAZARD:
• Never contact combustible material to the lens.
• Keep spotlight lamp away from materials that may burn.
CAUTION: TO REDUCE THE RISK OF INJURY OR PROPERTY DAMAGE:
• All lights give off heat:
– Do not touch lens while operating.
– Keep combustibles away from spotlight lens. Extreme heat can cause fires.
– Never place the light face down on any surface when lit, charging or not in use. Never store
the light face down on any surface.
• Never look directly into the light or shine the light into another person’s eyes.
• Keep sharp objects away from lens — it can crack or break.
• Do not expose this unit to extremely high temperatures.
• Do not drop or throw spotlight. It contains a lithium-ion battery.
• Use only with either the AC or DC charging adapter and USB charging cable that are provided
with unit. Plug in the charging cable at the light first, then plug into the charging source.
• After charging/recharging, disconnect charging adapter or extension cord and wait 5 minutes
before use.
• Do not crush, cut, pull or expose charging adapter cords to extreme heat.
• Position charging adapter cords so they do not become entangled or become a safety hazard.
Keep charging adapter cords away from sharp edges.
• There are no user-serviceable parts inside. Do not attempt to disassemble any other parts of
the unit.
• To reduce risk of damage to electric plug and cord, pull by plug rather than cord when
disconnecting.
• Do not attempt to charge the unit if the charger or cord is damaged – return the charger to
manufacturer for repair or replacement.
SPECIFIC SAFETY INSTRUCTIONS FOR LITHIUM-ION
BATTERIES
WARNING: TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, BURST HAZARD, OR INJURY TO
PERSONS OR PROPERTY:
Lithium-ion batteries are small, compact and ideal for providing long-lasting power to this unit.
However, they must be used and charged properly. Improper use can result in serious injury, fire,
or death.
• Lithium-ion batteries can explode in the presence of a source of ignition. Do not use the product
in the presence of an open flame.
• Do not place this lithium-ion battery powered unit in fire or apply heat to it.
• Do not subject this lithium-ion battery powered unit to strong impacts or shocks. The battery
in this unit contains safety and protection devices which, if damaged, may cause the battery to
generate heat, rupture or ignite.
• Do not expose this lithium-ion battery powered unit to water or salt water, or allow the battery
to get wet.
• Avoid storing this lithium-ion battery powered unit in the basement, bathroom or other areas of
the house that are or may become wet or humid or where moisture may concentrate.
• Do not leave this lithium-ion battery powered unit in direct sunlight, or use or store the unit
inside cars in hot weather. Doing so may cause the battery to generate heat, rupture, or ignite.
Using the battery in this manner may also result in a loss of performance and a shortened life
expectancy.
• Never charge this unit near heat or flammable objects.
• NEVER THROW WATER ON A BURNING LI-ION BATTERY! If a lithium-ion battery does catch on
fire, it will burn even more violently if it comes in contact with water or even moisture in the
air. A fire extinguisher must be used.
Battery Charging and Capacity
This unit is delivered in a partially charged state – you must fully charge it before using it for the
first time.
When stored at room temperature with a full charge, Li-ion batteries will will begin to discharge
from the time they are manufactured, even when unused. Deep discharges also decrease their
capacity. Battery life can be extended by the following:
• Charge battery to full capacity before storage.
• Optimal storage temperature for this unit is between 5°C and 20°C (41°F and 68°F).
• Never discharge the battery fully.
• Charge after each use.
• Always charge at least once every 3-6 months if not in frequent use to prevent overdischarge.
Transportation of Lithium-Ion Batteries
• Always check all applicable local, national, and international regulations before transporting a
unit containing a Lithium-Ion battery.
• Transporting an end-of-life, damaged, or recalled battery may, in certain cases, be specifically
limited or prohibited.
INSTRUCTIONS PERTAINING TO WATERPROOF SPOTLIGHTS
The rubber “O” ring acts to preserve the waterproof qualities of the spotlight. The “O” ring seals
the end cap to prevent water from entering the gap. An undamaged rubber “O” ring, rubber bezel
and lens, and proper sealing of the end cap before use are very important.
CAUTION: TO REDUCE THE RISK OF PROPERTY DAMAGE:
• Attempting to remove the rubber “O” ring; use of the unit with a damaged “O” ring, rubber
bezel or lens; improper sealing of the waterproof end cap; and/or submerging this unit in depths
greater than 6 feet may cause the unit to no longer be waterproof. Do not submerge the unit if
these conditions exist or the unit could sustain permanent damage.
• Submerging this unit in depths greater than 6 feet and/or operating it in water temperature other
than between 41ºF and 104ºF (5ºC and 40ºC) could result in leakage, warping or malfunction,
causing permanent damage to the spotlight.
INSTRUCTIONS PERTAINING TO THE 12V DC/USB CHARGING
ADAPTER
CAUTION: TO AVOID THE RISK OF PROPERTY DAMAGE:
• NEVER CONNECT THE UNIT TO A POSITIVE GROUNDED VEHICLE.
• The 12 Volt DC charging adapter must only be connected to batteries with a nominal output
voltage of 12 volts. The unit will not operate from a 6 volt battery and will sustain permanent
damage if connected to a 24 volt battery.
• Always connect the 12 volt DC/USB charging adapter to the 12 volt DC power source before
plugging any devices into it
INSTRUCTIONS PERTAINING TO THE USB PORTS
• IMPORTANT: Some household USB-powered electronics will not operate with the USB ports
provided with this device. Check the manual of the corresponding electronic device to confirm
that it can be used with this type of USB port.
• The USB ports do not support data communication. They only provide power to an external
USB powered device (5VDC/2.1A using the USB port on the DC /USB charging adapter or 5VDC/1A
using the AC/USB charging adapter). Make sure the rating of equipment plugged into the USB
port does not exceed the amperage stated.
• Always connect the appropriate charging adapter to either the 120 volt AC or 12 volt DC power
source before plugging any devices into it.
• Do not attach USB hubs allowing connection of multiple personal electronic devices to any of the
USB ports on the charging adapters.
SAVE THESE INSTRUCTIONS
INTRODUCTION
Congratulations on purchasing your new Stanley® FatMax® Spotlight. Read this Instruction
Manual and follow the instructions carefully before using your new spotlight.
FEATURES
1. LED bulb
2. Rubber bezel
3. On/off trigger
4. Grip handle
5. Micro-USB charging port (for use with the USB Charging Cable and Charging Adapters)
6 Battery/charge status LED indicator
7. Translucent waterproof end cap (see detailed view in the “Reading the Battery/Charge Status
LED Indicator” section)
8. Rubber O-ring
9. USB charging cable (for use with 12V DC/USB Charging Adapter and 120V AC/USB Charging
Adapter)
10. Regular USB plug
11. Micro-USB plug
12. 12V DC/USB Charging Adapter (Optional Accessory)
13. 12V DC/USB Charging Adapter LED Indicator
14. 12V DC/USB Charging Adapter USB Port (Optional Accessory)
15. 120V AC/USB Charging Adapter (Optional Accessory)
16. 120V AC/USB Charging Adapter USB Port (Optional Accessory)
READING THE BATTERY/CHARGE STATUS LED INDICATOR
The battery and charging status LED indicator is located directly above the micro-USB charging port
under the waterproof end cap on the back of the unit.
DOT ICON (FOR ALIGNMENT
TO THE TRIANGULAR ICON
ON THE END CAP)
TRIANGULAR ARROW
ICON (FOR ALIGNMENT
TO THE DOT ICON ON THE
REAR OF UNIT)
END CAP DETAIL
It lights or flashes in three colors to indicate the following:
When charging:
Green: Battery is in a fully charged state.
Green (flashing): Battery is in a high partially charged state.
Orange (flashing): Battery is in a low partially charged state.
Red (flashing): Battery needs to be recharged.
Red (flashing rapidly): The battery of the unit is overheated due to extensive use or recharging.
The charging process will stop at this stage and will automatically resume after a cool down period.
When operating:
Green: Battery is operating at full voltage.
Orange: Battery is operating at partial voltage.
Red: Battery is operating at low voltage, and should be recharged or the built-in low voltage
protection will be activated and the unit will automatically shut down shortly.