Installation Sheet

ManualsBrandsSTANLEY ManualsCommercial HardwareQDC100 Series Surface Mount Door Closer Adjustable from sizes 1 to 6 with Extra Duty Tri-Pack and Hold-Open

NOTICE

IT IS IMPORTANT TO CAREFULLY

FOLLOW ALL INSTALLATION AND

MOUNTING INSTRUCTIONS WHEN

INSTALLING ANY DOOR CLOSER.

MAXIMUM

DOOR WIDTH

FULL TURNS OF POWER

ADJUSTING SCREW

CW = clockwise CCW = counterclockwise

EXTERIOR

(SWING OUT)

DOOR

CLOSER

SIZE

INTERIOR

28” (0.71m)

14 CCW

12 CCW

6 CCW

QDC111 QDC111BF

3 CCW

3 CW

7 CW

12 CW

4 CW

0 (PRESET) 0 (PRESET)

8 CCW

36” (0.91m)

42” (1.07m)

48” (1.22m)

54” (1.37m)

5 lb-f

32” (0.81m)

36” (0.91m)

42” (1.07m)

48” (1.22m)

54” (1.37m)

58” (1.47m)

*NOTICE

TURNS REQUIRED ARE APPROXIMATE DUE TO VARIOUS DOOR CONDITIONS AND

LOCATIONS. FURTHER ADJUSTMENTS FOR SPRING POWER MIGHT BE NECESSARY

TO SUIT YOUR REQUIREMENTS.

LATCH SPEED

CONTROL SCREW

BACK CHECK

SCREW

SWEEP SPEED

CONTROL SCREW

DELAYED ACTION

CONTROL SCREW

SPRING POWER

ADJUSTING SCREW

THREE INSTALLATION OPTIONS: A, B, AND C.

OPTION A: REGULAR ARM MOUNT

(PULL SIDE)

OPTION B: TOP JAMB MOUNT

(PUSH SIDE)

OPTION C: PARALLEL MOUNT

(PUSH SIDE)

RIGHT HAND DOOR = RH

LEFT HAND REVERSE = LHR

LEFT HAND DOOR = LH

RIGHT HAND REVERSE = RHR

RIGHT HAND DOOR = RH

LEFT HAND REVERSE = LHR

CCW

CONTROL RANGE

BACK CHECK

DELAYED ACTION

SWEEP

LATCH

Increase

Decrease

Increase

Decrease

Slow

Fast

Slow

Fast

DOOR HANDING

DOOR HANDS DETERMINED FROM OUTSIDE

LEFT HAND

RIGHT HAND

INSIDE

OUTSIDE

INSIDE

OUTSIDE

LEFT HAND

REVERSE BEVEL

RIGHT HAND

REVERSE BEVEL

COVER

SCREW

HOLES

SPRING POWER / SIZING

HEX

WRENCH

The closing force for series QDC111BF door closers is an adjustable form of a size 1 to a size 6, as

outllined in ANSI Standard A156.4. When these series of door closers are installed and adjusted to

conform to ADA reduced opening force requirements (5 lbs max) for interiror doors, they may not have

adequate closing force to reliably close and latch door. Power adjustments charted on this page are

recommended where possible to ensure proper door control.

By law, the Americans with Disabilities Act (ADA)

may require that door closer installation comply

with accessibility guidelines.

QDC100 SERIES

DOOR CLOSER

INSTALLATION INSTRUCTIONS

ENGLISH

Summary of content (12 pages)

PAGE 1
ENGLISH INSTALLATION INSTRUCTIONS NOTICE QDC100 SERIES DOOR CLOSER CONTROL RANGE DOOR HANDING INSIDE LEFT HAND Increase Increase Decrease Decrease INSIDE LEFT HAND REVERSE BEVEL DELAYED ACTION BACK CHECK RIGHT HAND OUTSIDE IT IS IMPORTANT TO CAREFULLY FOLLOW ALL INSTALLATION AND MOUNTING INSTRUCTIONS WHEN INSTALLING ANY DOOR CLOSER.
PAGE 2
OPTION A: REGULAR ARM MOUNT DOOR CLOSER MOUNTED ON PULL SIDE OF DOOR DOOR OPENING: 120° This diagram shows RIGHT-HAND DOOR. For LEFT-HAND DOOR, rotate door closer 180° (spring power adjusting screw facing towards door hinges). 2 HOLES FOR #14 1 15/16” *10 13/16” ALL-PURPOSE OR 1/4-20 (49,2mm) (274,6mm) (M6x1.0) MACHINE SCREW 11/16” (17,5mm) 2 1/4” (57mm) * 6 1/4” (158,8mm) 1” (25,4mm) 3” 76,2mm 11/16” (17,5mm) 1” (25,4mm) 4 HOLES FOR #14 ALL-PURPOSE OR 1/4-20 (M6x1.
PAGE 3
OPTION B: TOP JAMB MOUNT DOOR CLOSER MOUNTED ON TOP JAMB ON PUSH SIDE OF DOOR DOOR OPENING: 120° This diagram shows RIGHT-HAND DOOR. For LEFT-HAND DOOR, rotate door closer 180º (spring power adjusting screw facing towards door hinges). 4 HOLES FOR #14 ALL-PURPOSE OR 1/4-20 (M6x1.0) MACHINE SCREWS 1” (25.4mm) 3” (76.2mm) * 6 5/16” (160mm) 1” (25.4mm) 2 1/4” (57mm) 11/16” (17.5mm) 2 HOLES FOR #14 ALL-PURPOSE OR 1/4-20 (M6x1.0) MACHINE SCREWS 11/16” (17.5mm) 1 15/16” (49.
PAGE 4
OPTION C: PARALLEL MOUNT DOOR CLOSER MOUNTED ON DOOR ON PUSH SIDE OF DOOR DOOR OPENING: 180° This diagram shows LEFT-HAND DOOR. For RIGHT-HAND DOOR, rotate door closer 180º. 1 1/16” (27mm) 1 11/16” 1 11/16” (43mm) (43mm) 1 1/16” (27mm) 5 HOLES FOR #14 ALL-PURPOSE OR 1/4-20 (M6x1.0) MACHINE SCREWS 5/16” (8mm) 1 3/4” (44.5mm) 4” (101.6mm) 11/16” (17.5mm) 11 1/2” (292mm) = 90° OPENING 10” (254mm) = 120° OPENING 7 7/8” (200mm) = 180° OPENING 2 HOLES FOR #14 ALL-PURPOSE OR 1/4-20 (M6x1.
PAGE 5
18553652407 www. st anl eysecur i t ysol ut i ons.
PAGE 6
OPTION A: MONTAGE ORDINAIRE DU BRAS FERME-PORTE INSTALLÉ DU CÔTÉ DE LA PORTE SUR LEQUEL ON TIRE OUVERTURE DE LA PORTE: 120° Ce schéma montre une PORTE MAIN DROITE. Pour une PORTE MAIN GAUCHE, faire tourner le ferme-porte de 180° (la vis de réglage de la puissance du ressort doit faire face aux charnières de la porte). 2 TROUS POUR VIS DE MÉCANIQUE #14 1 15/16” *10 13/16” POLYVALENTE OU 1/4-20 (49,2mm) (274,6mm) LIGNE CENTRALE POUR LA CHARNIÈRE OU LE PIVOT (M6x1.
PAGE 7
OPTION B: MONTAGE SUR LE MONTANT SUPÉRIEUR FERME-PORTE INSTALLÉ SUR LE MONTANT DE PORTE SUPÉRIEUR DU CÔTÉ DE LA PORTE SUR LEQUEL ON POUSSE OUVERTURE DE LA PORTE: 120° Ce schéma montre une PORTE MAIN DROITE. Pour une PORTE MAIN GAUCHE, faire tourner le ferme-porte de 180° (la vis de réglage de la puissance du ressort doit faire face aux charnières de la porte). 1” (25.4mm) 3” (76.2mm) 4 TROUS POUR VIS DE MÉCANIQUE #14 POLYVALENTE OU 1/4-20 (M6x1.0) 6 5/16” (160mm) * 1” (25.
PAGE 8
OPTION C: MONTAGE PARALLÈLE FERME-PORTE INSTALLÉ DU CÔTÉ DE LA PORTE SUR LEQUEL ON POUSSE OUVERTURE DE LA PORTE: 180° Ce schéma montre une PORTE MAIN GAUCHE. Pour une PORTE MAIN DROITE, faire tourner le ferme-porte de 180°. 1 1/16” (27mm) 1 11/16” 1 11/16” (43mm) (43mm) 1 1/16” (27mm) 5 TROUS POUR VIS DE MÉCANIQUE #14 POLYVALENTE OU 1/4-20 (M6x1.0) 5/16” (8mm) 1 3/4” (44.5mm) 4” (101.6mm) 11/16” (17.
PAGE 9
18553652407 www. st anl eysecur i t ysol ut i ons.
PAGE 10
OPCIÓN A: MONTAJE REGULAR DEL BRAZO CIERRA PUERTAS MONTADO SOBRE EL LADO PARA JALAR LA PUERTA ABERTURA DE LA PUERTA: 120° Este diagrama demuestra PUERTA DERECHA. Para PUERTA DE LA MANO IZQUIERDA, gire el cierra puertas 180º (revestimiento del tornillo de reglaje de la energía del resorte hacia las bisagras de puerta). *10 13/16” LÍNEA CENTRAL DE LA BISAGRA O DEL PIVOTE 2 AGUJEROS PARA #14 MULTIUSO O 1/4-20 (M6x1.
PAGE 11
OPCIÓN B: MONTAJE SUPERIOR DE LA CANILLERA CIERRA PUERTAS MONTADO SOBRE LA JAMBA SUPERIOR EN EL LADO DE EMPUJE DE LA PUERTA ABERTURA DE LA PUERTA: 120° Este diagrama demuestra PUERTA DERECHA. Para PUERTA DE LA MANO IZQUIERDA, gire el cierra puertas 180º (revestimiento del tornillo de reglaje de la energía del resorte hacia las bisagras de puerta). 4 AGUJEROS PARA #14 MULTIUSO O 1/4-20 (M6x1.0) TORNILLOS DE MAQUINA 1” (25.4mm) 3” (76.2mm) * 6 5/16” (160mm) 1” (25.4mm) 2 1/4” (57mm) 11/16” (17.
PAGE 12
OPCIÓN C: MONTAJE PARALELO CIERRA PUERTAS MONTADO SOBRE LA PUERTA EN EL LADO DE EMPUJE ABERTURA DE LA PUERTA: 180° Este diagrama demuestra PUERTA IZQUIERDA . Para PUERTA DE LA MANO DERECHA, gire el cierra puertas 180º. 1 1/16” (27mm) 1 11/16” 1 11/16” (43mm) (43mm) 5 AGUJEROS PARA #14 MULTIUSO O 1/4-20 (M6x1.0) TORNILLOS DE MAQUINA 1 1/16” (27mm) 1 3/4” (44.5mm) 5/16” (8mm) 4” (101.6mm) 11/16” (17.