Manualshelf

Installation Sheet

ManualsBrandsSTANLEY ManualsCommercial HardwareQDC200 Series Surface Mount Door Closer Adjustable from sizes 1 to 6 with Standard Duty Tri-Pack Arm and Slim-Line Cover
1234
Option A –
Regular Arm Installation
Option C –
Parallel Arm Installation
Option A instructions: 1. Using the measurements from diagram A, mark screw hole center locations. Mark four (4) location on door to mount door closer and
two (2) locations on door frame to mount arm shoe. 2. Drill pilot holes in door and frame, 7/32” (5.5mm) diameter for wood, or #7 (.201” diameter) for all purpose screws
or 1/4-20 machine screws. 3. Install adjustable forearm/arm shoe to frame using screws (a) or (b). 4. Mount closer onto door using screws (c) or (d). SPEED ADJUST-
ING VALVES MUST BE POSITIONED TOWARD HINGE SIDE. 5. Install main arm to top pinion shaft, perpendicular to door. Secure tightly with arm screw/washer (e).
6. Adjust length of forearm so that forearm is perpendicular to frame when assembled to preloaded main arm.S ecure forearm to main arm with screw/washer (f).
7. Adjust door’s closing speed and power, see page 4 for reference. 8. Snap pinion cap over shaft at bottom of closer or install (optional) cover with small screws (j).
Option B Instructions: 1. Using the measurements from diagram B, mark screw hole center locations. Mark four (4) location on frame to mount door closer and
two (2) locations on door to mount arm shoe.
2. Drill pilot holes in door and frame, drill 7/32” (5.5mm) diameter holes for wood screws or drill and tap #7 (.201” diameter)
for 1/4-20 machine screws.
3. Install adjustable forearm/arm shoe to frame using screws (a) or (b). 4. Mount closer onto frame using screws (c) or (d). SPEED ADJUST-
ING VALVES MUST BE POSITIONED TOWARD HINGE
SIDE.
5. Install main arm to bottom pinion shaft, perpendicular to door. Secure tightly with arm screw/washer
(e). 6. Adjust length of forearm so that forearm is perpendicular to door when assembled to preloaded main arm. Secure forearm to main arm with screw/washer (f).
7. Adjust door’s closing speed and power, see page 4 for reference.
8. Snap pinion cap over shaft at bottom of closer or install (optional) cover, using small screws (j).
Option C Instructions: 1.
Using the
measurements from diagram C, mark screw hole
center locations. Mark four (4) location on door to
mount door closer and four (4) locations on inside
frame to mount parallel bracket.
2. Drill pilot holes in
door and frame, drill 7/32” (5.5mm) diameter holes for
wood screws or drill and tap #7 (.201” diameter) for
1/4-20 machine screws.
3. Install Parallel Bracket to
frame using screws (g) or (h). 4. Mount closer onto
door using screws (c) or (d). SPEED ADJUSTING
VALVES MUST BE POSITIONED AWAY FROM
HINGE
SIDE.
5. Place main arm on closer pinion
shaft, indexing main arm mark “L” or “R with pinion flat
as shown in figure 1. Secure tightly with screw/washer
(e). 6. Remove arm shoe from forearm (see figure 2).
Install ROD end of forearm to bracket using the screw
(i). 7. With door closed, adjust length of forearm so
that the tip of the main arm is approximately 1-1/2”
(38mm) away from being parallel with door, when
connected to the forearm. Secure with screw/washer
(f).
8. Adjust door’s closing speed and power, see
page 4 for reference. 9. Snap pinion cap over shaft at
bottom of closer or install (optional) cover, using small
screws (j).
Diagram for Option B
12
(304.8)
131° to 180°
101° to 130°
To 100°
Door Opening Dim. A
4
-1/2
6
7
-1/2
(114)
(152)
(191)
Hinge or Pivot
A
3/4
(19)
1/2
(13)
1
-3/4
(44.4)
1
-7/8
(48
Inche
)
s (mm)
5
-1/2
(140)
Left hand door shown, reverse
measurements of right hand
door application.
Left hand door shown,
reverse measurements
for a right hand door
application.
1/2
(13)
7/16
(11)
2
(50.8)
2
-3/4
(70)
A
3/8
(9.5)
3
-1/2
(89)
3/4
(19)
B
12
(304.8)
121° to 180°
To 120°
Door Opening Dim. B
1
-1/4
3
-3/4
(32)
(95)
Dim. A
7
9
-1/2
(178)
(241)
Inches (mm)
Hinge or Pivot
Diagram for Option C
1-
1/2
(38)
131° to 180°
101° to 130°
To 100°
Door Opening Dim. A
4
-1/2
6
7
-1/2
(114)
(152)
(191)
Hinge or Pivot
3/4
(19)
1
-3/8
(35)
12
(304.8)
1
(25.4)
5
-1/2
(140)
A
1
-3/4
(44.4)
Inches (mm)
Right hand door shown,
reverse measurements for
left hand door application.
SPEED ADJUSTING VALVES
DOOR CLOSER
(R
ight Hand Door)
(Right Hand Door)
(Left Hand Door)
(Left Hand Door)
(Right Hand Door)
ARM SHOE
MAIN ARM
FOREARM
SPEED ADJUSTING VALVES
DOOR CLOSER
(Left Hand Door)
ARM SHOE
MAIN ARM
FOREARM
DOOR CLOSER
SPEED ADJUSTING VALVES
ARM SHOE
FOREARM
MAIN ARM
DOOR CLOSER
SPEED ADJUSTING VALVES
ARM SHOE
FOREARM
MAIN ARM
DOOR CLOSER
SPEED
ADJUSTING
VALVES
PARALLEL
BRACKET
FOREARM
MAIN ARM
DOOR CLOSER
SPEED
ADJUSTING
VALVES
PARALLEL
BRACKET
FOREARM
MAIN ARM
Option B –
Top Jamb Installation
Diagram for Option A
Figure 2
1
3
2
ARM SHOE
FOREARM
Figure 1
Left hand door
Main arm
Right hand door
Main arm
S
R
L
S
R
X1
L
1 of 4
INSTALLATION INSTRUCTIONS
QDC 200
This sheet covers 3 installation options; select appropriate installation.
Diagram measurements are not to scale.
Machine X2
Machine X4
Machine X4
Wood X2
Wood X4
Wood X4
Optional
cover
(a)
screw.
(c)
(e)
(b)
(d)
(f)
(g)
(h)
(i) (j)
X1
X1
X1
X1
Incorrect installation or
adjustment could
cause damage or injury.
Read and follow
instructions carefully.

Summary of content (4 pages)