STGS9100 STGS9115 STGS9125 English Page 4
ENGLISH (Original instructions) Figure 1 b a c n Figure 2 Figure 3 c h g f d k i 2 e
(Original instructions) Figure 4 ENGLISH Figure 5 h f d 15o-30o e A B Figure 6 3
ENGLISH (Original instructions) Definitions: Safety Guidelines The definitions below describe the level of severity for each signal word. Please read the manual and pay attention to these symbols. Danger: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. Warning: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
(Original instructions) ENGLISH c. Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool.Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents. e. Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tools operation.
ENGLISH (Original instructions) e) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannon be adequately guarded or controlled. k) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning accessory.
ENGLISH (Original instructions) a) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum control over kickback or torque reaction during start up. The operator can control torque reaction or kickback forces, if proper precautions are taken. b) Never place your hand near the rotating accessory. Accessory may kickback over your hand.
ENGLISH (Original instructions) Package Content This product package includes: Do not use the tool in wet conditions or environments in the presence of flammable liquids or gases. This heavy-duty angle grinder is a professional power tool. 1 Angle grinder Do not allow children to come in contact with this tool.
(Original instructions) Attaching and Removing the Wheel Guard (Fig. 2) Warning: To minimize the danger of serious personal injury, please switch off the tool power and disconnect all plugs before adjusting or removing/installing any accessory. Before reassembling the tool, press and release the trigger switch to make sure the tool is already switched off. Attaching the Guard 4. Tighten the outer flange (h) until the output shaft (e) (Fig. 4).
ENGLISH (Original instructions) 2. Keep the edge of the wheel tilted at angle from 15 to 30 degrees against the surface of the workpiece. 3. When using a new grinding wheel, do not operate the wheel in the B direction, otherwise, it will cut into the workpiece. When the edge of wheel has been rounded off, you are free to operate the grinder in either the A or B direction. Starting and Stopping (Fig. 1) Warning: Before using the tool, check whether the handle is tightened securely.
(Original instructions) Warning: Under extreme working conditions, conductive dust and grit may accumulate on the housing interior when handling metal workpieces. This could create an electric shock hazard as it weakens the protective insulation in the grinder. To avoid accumulation of metal chips in the interior of the grinder, we recommend cleaning the ventilation ducts daily. Refer to Maintenance. Using Grinding Wheels Warning: Metal powder accumulates.
ENGLISH (Original instructions) Protecting the environment Separate collection. This product must not be disposed of with normal household waste. Should you find one day that your STANLEY product needs replacement, or if it is of no further use to you, do not dispose of it with household waste. Make this product available for separate collection. Separate collection of used products and packaging allows materials to be recycled and used again.
N a m e s & A d d r e s s e s f o r S TA N L E Y S e r v i c e C o n c e s s i o n a r i e s - I N D I A ASSAM: Arun Machine And Tools, A.T.Road, Near Rupshree Cinema, Tokobari, Guwahati, Assam, Pin: 781001, Mob: 9435118754, Tel: 2591868. Bagaria Tools And Hardware, Near Hotel Vishwaratna, At Road, Guwahati, Assam, Pin: 781001, Mob: 9864077172/9435011008, Tel: 2511173. Vinayak Tools And Machinery, A1-, Mangal Ram Tower, Opposite Police Reserve, A.T.Road, Guwahati, Assam, Pin: 781001, Mob: 9435049234.
KERALA: Tool Tech Inc, Door No. 932 & 931/16b, Aradhana Tourist Home, Kallai Road, Calicut, Pin: 673002, Mob: 9388485464, Tel: 4025071 0495. Powertool Enterprises, 2133/44e, Freedom Road, Kaloor, Kochi, Kerala, Pin: 682017, Mob: 9895405593, Tel: 4047593-0484. Tool World, 2708/44c Karukappilly, Deshabhimani Road, Kochi,kerala, Pin: 682017, Mob: 9388485378, Tel: 2409745/3295546-0484. Vindia Enterprises, 3686/39, Ravipuram Road, Ernakulam, Cochin, Kerala, Pin: 682016, Mob: 9847219831, Tel: 2356924-0484.
N438243 04/2015