MODEL NO. SXAC2036121 For service, spare parts or product information, please contact Smart Marketing Group Pty. Ltd. AUST. 1300 660 457 N.Z.
SUGGESTED APPLICATIONS CONTENTS You may use some light duty air tools with this compressor. Some examples of light duty tools are: Section • Ball Inflator Contents 2 • Toy Inflator Suggested Applications 2 Introduction 3 • Tyre Inflator • Mini Air Brush Page • Touch Up Spray Can Guarantee 3–4 • Stapler General Safety Instructions 5–7 • Combo Nailer • C-Bradder • T-Nailer This light duty air compressor is NOT recommended for use with a spray gun.
INTRODUCTION What is covered. • Manufacturing fault or defect. Dear Customer, How to claim under this warranty. • Call customer service. • Ensure you have the following: Original purchase receipt, Model of compressor, Serial number of compressor. • Discuss the issue. • Customer service will advise which authorised service agent to take the compressor to provided the issue is a warranty one. • Take compressor to authorised service agent for repair.
COMPLETE WARRANTY STATEMENT – COMPRESSOR Damage caused by third party accessories is not covered under this warranty. As soon as you have purchased the compressor, we recommend that you check to make sure it is intact and that you read the operating instructions carefully before using it. The purchase receipt for this product is to be retained and must be presented if making a claim under the terms of the Smart Marketing Group (SMG) warranty.
LUBRICATION OF COMPRESSOR WORK ENVIRONMENT This compressor is OIL FREE. Therefore there is NO oil used for lubrication. Do not expose your air compressor to rain or use in damp or wet conditions. Keep the work area well lit. Always ensure your compressor is level and stable. Using your compressor on unlevel or unstable ground may cause it to tip over, this damage will not be covered under warranty. Do not use your air compressor in the same area that you are spray painting or sanding.
DO NOT ABUSE THE POWER CORD DISCONNECT AIR COMPRESSOR Ensure that the air compressor is disconnected from the mains supply when not in use, before servicing, cleaning, making adjustments or when changing any accessories. Never yank or pull on the power cord to disconnect it from the mains supply socket. Never carry or pull your air compressor by its power cord. Keep the power cord away from heat, oil, solvents and sharp edges.
CHECK DAMAGED PARTS PERSONAL SAFETY Before using the air compressor it should be carefully checked to determine that it will operate properly and perform its intended function. Clothing Do not wear loose clothing, jewellery or anything that could get caught in moving machinery. Hair Long hair should be tied back or contained in a protective covering. Eye Protection The use of safety goggles is highly recommended (normal glasses are not sufficient for eye protection) when using an air compressor.
IMPORTANT ELECTRICAL DATA This air compressor is fitted with a sealed electrical connection plug that is compatible with the mains power supply for Australia / New Zealand and meets the requirements of international standards. This air compressor must be connected to a supply voltage that is equal to that stated on the rating label.
10 9 13 10 9 8 13 11 1 12 14 2 3 4 7 5 COMPONENTS AND CONTROLS 1. Rear handle 2. Tank 3. Wheels 4. Tank drain tap 5. Rubber stopper 6. Safety Valve (not shown) 7. Tank pressure gauge 8. Front handle 9. Pressure switch 10. On / Off button – red colour 11. Outlet pressure gauge 12. Air outlet - nitto style socket 13. Outlet pressure regulator 14. Water filter 15.
OPERATING INSTRUCTIONS PIC. 1 Unpacking Carefully unpack your air compressor. This air compressor is bulky and heavy, two (2) person lift required. Dispose of all packing material in an environmentally responsible manner. Assembly Your air compressor requires minor assembly before initial operation. Check that you have all required components required for assembly and initial use. RUBBER STOPPER To attach the rubber stopper to the bracket located on the bottom of the tank; 1.
HANDLE PIC. 3 1. Loosen bolts in tubes welded to the tank. Tighten bolts to hold handle 2. Push handle into tubes welded on the tank. 3. Tighten the bolts to hold handle in place, Pic. 3. Slide handle into tubes AIR FILTER The supplied air filter must be used. PIC. 4 Failure to do so may result in irreparable damage and will void the warranty, Pic. 4. To install; 1. Carefully screw supplied air filter into the threaded hole on the top of the pump head. This only needs to be done up by hand.
USING THE AIR COMPRESSOR FILTER REGULATOR Your compressor does not require running in. Before use ensure you have read and understood these instructions. Pic. 6 Before use ensure this compressor is fully assembled as per pages 10 and 11. This air compressor comes with a filter regulator, which will filter some water and other particulates from the air as it passes through the regulator. Before starting run through this simple list; To drain any fluid from the filer regulator; 1. Fully assembled.
PIC. 7 Not supplied, purchased separately. The configuration of tools and accessories can be varied to suit your particular requirements. A basic recommended set up is shown in Pic. 7. When you have finished using your air compressor follow these simple steps; 1. Turn your air compressor OFF, using the ON/OFF switch. 2. Turn the power point OFF and disconnect the power lead. 3. Disconnect your air tools and air hose. 4. Clean your air hose and air tools. 5.
ADJUSTING THE PRESSURE PIC. 8 To adjust the outlet air pressure, use the red coloured regulator knob and check the pressure on the outlet pressure gauge, Pic. 8. Regulator If the pressure needs to be lower, turn anti clockwise. If the pressure needs to be higher, turn clockwise. Use the gauge to ensure you set the correct working pressure. Air Outlet Note: Different air tools require different operating pressures. Always check with the tool manufacturer if unsure.
AIR FITTING PIC. 10 Pic. 10 This air compressor is fitted with a ‘Nitto style’ (female) socket. 1. Push in the ‘Nitto style’ male plug (not included). Outlet pressure gauge 2. Fully and completely push the ‘Nitto style’ male plug (not included) into the ‘Nitto style’ female socket until it clicks and the collar locates forward. To remove 1. Push collar down and remove male fitting, collar will stay retracted.
MAINTENANCE Daily: Before use 1. Seal the tank drain tap,see page 15, Pic. 11. 2. Check safety valve operation,see page 14, Pic. 9. After Use 1. Open the tank drain tap,see page 15, Pic. 11 and leave open to allow to drain. 2. Wipe down the compressor. 3. Store safely and securely. TROUBLE SHOOTING If your compressor does not start • Check that you have plugged the power lead into a standard 240V 10Amp power point and turned the switch ON. • Check that you have turned the air compressor ON/OFF switch ON.
PARTS DIAGRAM Part Description Qty SMG Part No. Part Description Qty SMG Part No.
TECHNICAL INFORMATION * Specifications Inflator SXAC2036121 Voltage 240V AC ~ 50Hz Motor Electric 2 HP Wattage 1500W No Load Speed 2850 RPM Free Air Delivery (FAD) 105L per minute Tank Size 36L Duty Cycle 75% Max.
