MODEL NO.
CONTENTS Section Page Contents 2 Description & Components Suggested Applications 2 Unpacking 2 Years Warranty / Serial Number 2 Assembly 10 – 12 Specifications 3 Operation 12 - 15 Introduction 4 Maintenance 15 – 17 Express Warranty Statement 4 Trouble Shooting 18 Complete Warranty Statement 5 Service Log 19 Contact Information 20 Important Safety Instructions Section 6-8 Page 9 10 SUGGESTED APPLICATIONS These are some suggested articles which could be used by this line trim
OWNER’S OPERATING MANUAL PETROL LINE TRIMMER CURVED SHAFT 4 STROKE 26CC MODEL NO. SXPG42601 SPECIFICATIONS Engine type............................................................................................................................................... 4-stroke, air cooled Engine displacement......................................................................................................................................................... 26cc Engine max. speed..................................
INTRODUCTION Dear Customer, Thank you for purchasing this Line Trimmer which has passed through our extensive quality assurance processes. Every care has been taken to ensure that it reaches you in perfect condition. However, in the unlikely event that you should experience a problem, or if you require any assistance please do not hesitate to contact us. If you have a problem, call customer service (phone number to the right), do not return this Line Trimmer to the place of purchase.
COMPLETE WARRANTY STATEMENT - LINE TRIMMER As soon as you have purchased the Line Trimmer, we recommend that you check to make sure it is intact and that you read the operating instructions carefully before using it. The purchase receipt for this product is to be retained and must be presented if making a claim under the terms of the Smart Marketing Group (SMG) warranty. Bank account statements are not acceptable for proof of purchase. costs associated with the service will be charged to the owner.
IMPORTANT SAFETY INSTRUCTIONS The purpose of safety rules is to attract your attention to possible dangers. The safety symbols and the explanations with them, require your careful attention and understanding. The safety warnings do not by themselves eliminate any danger. The instruction or warnings they give are not substitutes for proper accident prevention measures. SPECIFIC SAFETY INSTRUCTIONS Read the instructions with due care.
IMPORTANT SAFETY INSTRUCTIONS Never start or run the product inside a closed room or building. Fumes from the exhaust contain dangerous carbon monoxide. If the unit will not be used for a long time, clean the unit completely, especially the fuel/oil tank, its surroundings, and the air cleaner. Never attempt to make engine adjustments while the unit is running. Always make engine adjustments with the unit resting on a flat, clear surface.
IMPORTANT SAFETY INSTRUCTIONS Be careful not to drop the unit or hit it against obstacles. RESIDUAL RISKS Before proceeding to adjust or repair the unit, be sure to stop the engine and detach the spark plug. Even when the unit is used as prescribed it is not possible to eliminate all residual risk factors.
DESCRIPTION DESCRI TION 3 4 5 2 1 11 13 12 14 6 7 10 15 8 9 For information regarding spare parts, please refer to contact details on the front of this manual 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15.
UNPACKING CAUTION. If any parts are found to be missing, please contact customer service (details on page 2 & 4). Do not throw the packaging away, keep it safe throughout the warranty period, then recycle if possible, otherwise dispose of it by the proper means. Do not let children play with empty plastic bags due to the risk of suffocation. This packaging contains sharp objects. Take care when unpacking. Remove the machine, together with the accessories supplied, from the packaging.
ASSEMBLY INSTALLING THE CUTTING HEAD SHIELD WARNING. The line cut-off blade on the cutting head shield is sharp. Avoid connection with the blade. Failure to avoid contact can result in serious personal injury. 1. Locate the bolt, nut and washer used to fix the cutting head shield. 2. Align the screw hole in the mounting bracket with the screw hole in the cutting head shield, Fig. 4. 3. Push the bolt through the mounting bracket and into the cutting head shield and fix in place with the washer and nut.
ASSEMBLY INSTALLING THE HARNESS Connect the latch on the shoulder harness to the strap hanger, Fig 7. Adjust the strap to a comfortable position, Fig. 8. WARNING. Do not allow familiarity with this product to make you careless. Remember that a careless fraction of a second is sufficient to inflict serious injury. WARNING. Always wear eye protection with side Fig. 7 shields marked to comply with ANSI Z87.1, along with hearing protection.
OPERATION TO CHECK ENGINE LEVEL BEFORE EACH USE 1. Separate the attachment from the power head. 2. Set power head on a flat level surface with shaft parallel to surface. 3. Unscrew the oil cap and remove. 4. Lubricant level should fall within the top of oil fill hole (the top of screw thread). 5. If level is low, add engine lubricant until the fluid level rises to the top of oil fill hole (the top of screw thread) and does not overfill, Fig.9. 6. Replace and tighten the oil cap. MAX Fig.
OPERATION TO RESTART A WARM ENGINE Ignition switch Do NOT push choke button in. a. Turn switch to “I” ON position. b. Ensure primer bulb has fuel inside. c. Rapidly pull starter/grip until engine starts. d. Squeeze throttle to provide fuel to engine and use for intended task. Throttle lever Throttle lever release TO STOP THE ENGINE Fig. 10 To stop the engine, depress the STOP switch to the “STOP”position. OPERATING THE TRIMMER WARNING. Engine housing can become hot during trimmer operation.
OPERATION TIPS FOR TRIMMING Avoid hot surfaces by always keeping the tool away from your body. Use the tip of line to trim grass; do not force string head into uncut grass. Cut all grass from top to down. This will prevent grass from wrapping around the shaft housing and string head which could cause damage from overheating. If grass becomes wrapped around the string head, STOP THE ENGINE, disconnect the spark plug wire, and remove the grass.
MAINTENANCE ENGINE OIL REPLACEMENT WARNING. Old engine oil is considered special waste and has to be disposed according to your local environment protection regulation. Do not pour the oil to garbage can, sewer, soil etc. 1. The engine oil replacement is easier if engine is warm (NOT HOT!). 2. Open the oil tank cap and drain the old oil to an approved container. 3.
MAINTENANCE REPLACING THE CUTTING LINE SPOOL 1. Open the cutting line spool by pressing two release buttons on the side and take out the winding core (Fig.14 & 15). 2. Divide a spare cutting line in 2 equal halves, fix it in the winding core and start to wind the cutting line in two separated rails (Fig.15). Please follow the indicated winding. 3. Fix the 2 line ends (approx. 15cm) at the opening to keep the line wound tightly. (Fig.16) 4.
Problem Possible Cause Solution No spark Check spark. Remove spark plug. Reattach the spark plug cap and lay spark plug on metal cylinder. Pull the starter rope and watch for spark at spark plug tip. If there is no spark, repeat test with a new spark plug. No fuel Push primer bulb until bulb is full of fuel. If bulb does not fill, primary fuel delivery system is blocked. Contact a servicing dealer. If primer bulb fills, engine may be flooded, proceed to next item.
This Service is to be complete within 20 hours or 3 months of purchase, which ever comes first. This Service is to be complete within 40 hours or 6 months of purchase, which ever comes first.
