MODEL NO. SXPW7032BS For service, spare parts or product information, please contact Smart Marketing Group Pty. Ltd. AUST. 1300 660 457 N.Z. 0800 474 876 03596 02/19 PETROL PRESSURE WASHER 6.
SUGGESTED APPLICATIONS CONTENTS These are some suggested applications where you could use your pressure washer: • Concrete driveway • Paved area • Car • Motorbike • Truck • Wall • Garden feature Section IMPORTANT Contents 2 Suggested Applications 2 Introduction 3 Warranty 3–4 General Safety Instructions 5–7 Specific Safety Instructions 8 Fuel & Oil Information 9 Components and Controls OIL (CHECK DAILY - ONLY USE 4 STROKE MOTOR OIL) This pressure washer is fitted with a Briggs & Stratton
INTRODUCTION What is covered. • Manufacturing fault or defect. Dear Customer, Thank you for purchasing this pressure washer which has passed through our extensive quality assurance processes. Every care has been taken to ensure that it reaches you in perfect condition. However, in the unlikely event that you should experience a problem, or if you require any assistance, please do not hesitate to contact us; How to claim under this warranty. • Call customer service.
COMPLETE WARRANTY STATEMENT – PRESSURE WASHER Rust and corrosion are not covered under this warranty. If a warranty fault is found, the freight cost will be credited to the owner. If no fault is found, the product will be returned and any costs associated with the service will be charged to the owner. Blockages caused by spider webs, insects, dirt, accumulated dust or incorrect oil are not covered by warranty. SMG reserves the right to replace or repair the appliance within the warranty period.
LUBRICATION OF ENGINE WORK AREA OIL (CHECK DAILY - ONLY USE 4 STROKE MOTOR OIL) This pressure washer is fitted with a Briggs & Stratton engine. Please refer to the enclosed Briggs & Stratton Engine Manual for details on warranty and servicing. Work areas and benches should be kept tidy. Cluttered benches and work areas can cause accidents. Floors should be kept clean and free from rubbish. Special care should be taken when the floor is slippery due to sawdust or wax.
MAINTAIN YOUR PRESSURE WASHER WITH CARE RISK OF DAMAGE Damage may occur if nozzle is used too close to appliance being cleaned. Always trial test the pressure washer on an inconspicuous part of the appliance. Beware poor paint and rust as the water will lift poor paint and cause rust spots to grow. Damage caused by pressure washer is not covered by warranty. When not using your pressure washer ensure the fuel choke is ‘OFF’. Never leave the fuel choke ‘ON’ as this can damage the carburettor.
PERSONAL SAFETY Do Not Over Reach Do not over reach. Keep a proper footing and maintain your balance at all times. Avoid using abnormal stances and awkward body positions. Clothing Do not wear loose clothing, jewellery or anything that could get caught in moving machinery. Stay Alert Watch what you are doing, use common sense and never operate a pressure washer when you are tired, drinking alcohol, taking drugs or if taking medication that causes drowsiness.
SPECIFIC SAFETY INSTRUCTIONS • Do not attempt to modify the pressure washer, guards or the supplied accessories in any way. • Your pressure washer is factory set, NEVER attempt to speed it up as this could endanger the user and damage the pressure washer and/or attached appliances. • If the pressure washer makes an unfamiliar sound or vibrates excessively, switch the pressure washer ‘OFF’ immediately. Investigate the possible cause or consult your authorised service agent.
IMPORTANT FUEL - ONLY USE UNLEADED 91 PETROL (ULP - 91RON) - NO ETHANOL Fuel tank capacity – 3.1 litres (3.1 L) Use of incorrect fuel and/or oil may damage the pressure washer and will not be covered under warranty. Do not use E10 or any type of ethanol fuel as this will damage the pressure washer and will not be covered under warranty. Do not use high octane fuels (greater than 91%) as this will damage the pressure washer and will not be covered under warranty.
PIC. 1 1 3 9 2 8 4 6 5 7 COMPONENTS AND CONTROLS Pic. 1 1. Handle 2. Nozzles RED - YELLOW GREEN WHITE BLACK 3. Gun and trigger 4. Fuel tank 5. Lance 6. Recoil Starter 7. Wheel 8. High pressure hose 9.
UNPACKING & ASSEMBLY PIC. 2 Unpacking Note: Carefully unpack your pressure washer. This pressure washer is bulky and heavy, two (2) person lift required. Dispose of all packing material in an environmentally responsible manner. Open carton, gently lift the pressure washer clear of the carton and packaging, this may require 2 people. Remove from plastic bag. Note: Plastic bags can be a danger to young children, dispose of immediately. Always dispose of packaging in a responsible manner.
Hose to Pump PIC. 5 Pic. 5 1. Attach the high pressure hose to the pump. Pull back collar and push male connector in fully. Release collar. Ensure that the hose does not touch the muffler or goes over the top of the fuel tank. 2. Have hose lay to the back of the pump and curve to the hose hanger. Note: Do not allow high pressure hose to touch the muffler. Damage will occur and will not be covered by warranty.
OPERATING INSTRUCTIONS SELECTING NOZZLE Pre - Operation Preparation Note: If unit has previously been used, the motor, muffler and exhaust may still be hot enough to burn. Always exercise caution when checking the pressure washer. 1. Check that the fuel/engine switch is OFF. 2. Check that the spark plug lead is firmly attached to the top of the spark plug. 3. Holding on to the cage gently rock the pressure washer and listen for any noise which may indicate loose items.
Adding Lubricating Oil Always use clean fresh oil as specified on page 9. Incorrect or old oil can cause the pressure washer to run rough and damage the motor; this will not be covered by warranty. 1. Ensure that engine is OFF when filling oil. 2. Remove oil plug, see Pic. 9A 3. Use oil as detailed on page 9 (SAE 30W or SAE 15W-40 4 Stroke Motor Oil). 4. Ensure pressure washer is level when filling with oil. DO NOT TIP / USE A FUNNEL (Not Supplied). 5. Only fill oil to the top of the thread, Pic. 9B. 6.
STARTING YOUR PRESSURE WASHER PIC. 11 1. Check oil level. 2. Check and fill fuel. 3. Connect garden hose to cold water source. Do not turn on! 4. Connect garden hose to garden connection on pump. 5. Select nozzle, see page 13 6. If using detergent fill and select bottle refer page 14, Pic. 10. 7. Turn choke to start by sliding the choke lever to the LEFT, Pic 12. 8. Slide the fuel lever to ON by sliding the fuel lever to the right, Pic 11. 9. Push switch to “1”, refer Pic. 13. 10.
TAKING A BREAK DURING USE CLEANING If taking a break of more than 2 minutes during use you must turn the pressure cleaner off. Refer page 15 for how to do this. Damage will be caused if the pressure washer is left running while the trigger is off and no water coming out for more than 2 minutes. Damaged caused will not be covered under warranty. Pressure washer pump may also “dump” hot water as a self preservation, when the pump temperature gets too hot during this break time.
CLEANING TIPS Cars, Boats & Motorcycles - with or without detergent Pre-rinse vehicle with fresh water. If using vehicle wash, place detergent suction tube directly into cleaning solution and apply to surface at low pressure. For best results, clean one side of vehicle at a time and always apply detergent from bottom to top, do not allow detergent to dry on surface.
MAINTENANCE INFORMATION PIC. 18 If scheduled maintenance is NOT carried out then this will void your warranty. Use the Service Log on page 22 to keep track of the regular servicing. Ensure that the authorised service agent has dated, signed and stamped this log to ensure your warranty is not void. Fuel Tank Filter, Pic 18 The fuel tank filter should be checked every time you fill up the fuel tank. If dirty, replace.
Engine MAINTENANCE SCHEDULE OIL (CHECK DAILY - ONLY USE 4 STROKE MOTOR OIL) NOTE: If unsure how to do any of these checks please contact our service centre or an authorised service agent. NOTE: When performing any maintenance or servicing always ensure the pressure washer is stopped and turned off. This pressure washer is fitted with a Briggs & Stratton engine. Please refer to the enclosed Briggs & Stratton Engine Manual for details on warranty and servicing.
TROUBLE SHOOTING POSSIBLE CAUSE SUGGESTED FIX Engine will not start No or low fuel in the fuel tank Fill fuel tank No or low oil in sump Fill oil sump Fuel/Engine lever is OFF Turn fuel/engine lever ON Choke is set to RUN Slide choke to START Pressurised pump Turn water tap off, pull trigger to release water from pump.
PARTS DIAGRAM 1 4 3 7 6 5 2 8 User replaceable parts listed below. All other parts must be serviced/replaced by an authorised service agent. Part Description 1 Gun - trigger & Lance 84 PW5531GT 2 High pressure hose 10m QC 84 PW5531HPH 3 Nozzle yellow 84 PWNOZ 4 Nozzle black 84 PWNOZ 5 Nozzle red 84 PWNOZ 6 Nozzle white 84 PWNOZ 7 Nozzle green 84 PWNOZ 8 Wheel 84 PWWH Part No. Note: Gun, trigger and lance are all one code (84 PW5531GT).
This Service is to be complete within 50 hours or 3 months of purchase, which ever comes first. This Service is to be complete within 100 hours or 6 months of purchase, which ever comes first.
TECHNICAL INFORMATION Specifications Pressure washer SXPW7032BS Maximum pressure 3200PSI Flow rate 9L/min Water inlet pressure 0.4MPa Water inlet temp 35oC Engine 6.5HP Briggs & Stratton 4 stroke OHV Weight 35Kg (no fuel) Fuel volume 3.
For any queries or assistance call Customer Service AUST. 1300 660 457 NZ 0800 474 876 Hours of operation: Monday to Friday 8.00am - 5.00pm AEST Do not return to place of purchase. Keep your purchase receipt, this will be required to make any claims under the warranty, stated on page 3. STANLEY®, The STANLEY Logo, The Notched Rectangle and the Yellow and Black Diagonal Package Design are all trademarks of the Stanley Black & Decker, Inc or an affiliate thereof and are used under license.
