CD Player User Manual

ManualsBrandsStanton ManualsCD PlayerC.502

C.502

USER MANUAL

/ /

1. Handle the power supply cord carefully

Do not damage or deform the power supply cord.

If it is damaged or deformed, it may cause electric

shock or malfunction when used. When removing

from wall outlet,be sure to remove by holding the

plug attachment and not by pulling the cord.

2. In order to prevent electric shock, do not open the

top cover. If a problem occurs, contact your dealer.

3. Do not place metal objects or spill liquid inside the

CD player. Electric shock or malfunction may result.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARD, DO NOT

EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.

TO PREVENT ELECTRIC SHOCK DO NOT USE

THIS (POLARIZED) PLUG WITH AN EXTENSION

CORD, RECEPTACLE OR OTHER OUTLET UNLESS

THE BLADES CAN BE FULLY INSERTED TO

PREVENT BLADE EXPOSURE.

IMPORTANT TO SAFETY

NOTE:

This CD player uses the semiconductor laser. To allow

you to enjoy music at a stable operation, it is recommended

to use this in a room of 5ºC 41ºF - 35ºC 95ºF.

CAUTION:

Please, record and retain the Model name and serial

number of your set shown on the rating label.

Model No. ___________ Serial No. ___________

CAUTION: TO REDUCE THE

RISK OF ELECTRICf SHOCK,

DO NOT REMOVE THE COVER

(OR BACK) . THERE ARE NO

SERVICEABLE PARTS INSIDE.

The lightning flash with arrowhead symbol,

within an equilateral triangle, is intended to

insulated "dangerous voltage" within the

product's enclosure that may be of sufficient

magnitude to constitute a risk of electric

shock to persons.

The exclamation point within an equilateral

triangle is intended to alert the user to the

presence of important operating and

maintenance (servicing) instructions in the

literature accompanying the appliance.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

FOR U.S.A. & CANADA MODEL ONLY

CAUTION

CAUTION:

USE OF CONTROLS OR ADJUSTMENTS OR

REFORMANCE OF PROCEDURES OTHER THAN

THOSE SPECIFIED HEREIN MAY RESULT IN

HAZARDOUS RADIATION EXPOSURE.

THE COMPACT DISC PLAYER SHOULD NOT BE

ADJUSTED OR REPAIRED BY ANYONE EXCEPT

PROPERLY QUALIFIED SERVICE PERSONNEL.

DOUBLE INSULATED - WHEN SERVICING, USE

ONLY IDENTICAL REPLACEMENT PARTS.

NOTE:

This unit may cause interference to radio and television

reception.

Line Voltage Selection (for multiple voltage

model only)

The desired voltage may be set with the

VOLTAGE SELECTOR switch on the rear

panel, using a screwdriver.

Do not twist the VOLTAGE SELECTOR

switch with excessive force as this may

cause damage

If the VOLTAGE SELECTOR switch does not move

smoothly, please contact a qualified serviceman.

RATING LABEL

CLASS 1 LABEL

115V

230V

Summary of content (14 pages)

PAGE 1
C.
PAGE 2
IMPORTANT SAFETY PREC AUTIONS 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. Servicing - The user should not attempt any service to the appliance beyond that described in the operating instructions. All other servicing should be referred to qualified service personnel.. 16. Ventilation - Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered.
PAGE 3
IMPORTANT TO SAFETY WARNING: • TO PREVENT FIRE OR SHOCK HAZARD, DO NOT USE THIS PLUG WITH AN EXTENSION CORD, RECEPTACLE OR OTHEROUTLET UNLESS THE BLADES CAN BE FULLY INSERTED TO PRES ENT BLADE EXPOSURE. • TO PREVENT FIRE OR SHOCK HAZARD. NO NOT EXPOSE THIS APPLIANCE TO RAIN OR NOISTURE. • TO PREVENT ELECTRICAL SHOCK, MATCH WIDE BLADE PLUG TO WIDE SLOT FULLY INSERT. NOTE: This CD player uses the semiconductor laser.
PAGE 4
NOTE ON USE • • • • • • • • Allow for sufficient heat dispersion when installed in a rack. Handle the power cord carefully. Hold the plug when unplugging the cord. Keep the set free from moisture, water, and dust. Unplug the power cord when not using the set for long periods of time. Do not obstruct the ventilation holes. (For sets with ventilation holes.) Do not let foreign objects in the set. Do not let insecticides, benzene, and thinner come in contact with the set.
PAGE 5
MAIN FEATURES CONTROL UNIT / (1)OPEN/CLOSE (2)SINGLE/CONTINUE (3)TIME (4)TRACK BACKWARD (5)+10/FOLDER (6)TRACK FORWARD (7)F. BACKWARD (8)F.
PAGE 6
1. Checking the Contents Check that the carton contains the following items: 1) Main unit 2) Control unit 3) Operating instructions (this booklet) 4) Two pair of RCA pin cord. 5) Control cords (1 meter) 6) Power cord 7) Two fader start cables 2. Installing the Unit Mount the unit onto your console or rack with 19" EIA rack rails. CAUTION: The player will work normally when the main unit is mounted with the front panel at within 15 degrees of the vertical plane.
PAGE 7
NAMES AND FUNCTIONS Control Unit (1)OPEN/CLOSE Press it to open and close the disc holder. The main unit also includes OPEN/CLOSE buttons. The disc holder cannot be opened during playback, so stop playback before pressing the button. (2) SGL/CTN (Single/Continuous Button) Press it to switch between the single and continuous play modes.
PAGE 8
CONTROLS AND FUNCTIONS 7 7 1. AUTO CUE This will indicate if the Auto Cue is on or off. Press and hold the SGL/CTN for 1 sec. to turn the Auto Cue function on and off. 2.TRACK INDICATOR This 3-digit indicator displays the current track. The number displayed in the track indicator is a direct reference to a track being selected or a track in play, pause, or cue mode. 3.FOLDER/TRACK INDICATOR This indicator shows you if you are looking at the track number or the folder number. 4.
PAGE 9
1. Opening and Closing the Disc Holder Turn the unit power on . Press the OPEN/CLOSE button to open the disc holde r. OPEN/CLOSE buttons are provided on both the main unit and control unit. The disc holder cannot be opened during playback to prevent playback from being interrupted if the OPEN/CLOSE button is pressed accidentally. Stop the playback first, then press the OPEN/CLOSE button. 2.
PAGE 10
6. Pausing Press the PLAY/PAUSE button to switch between play and pause. The play indicator flashes when the pause mode is set. Figure 6 show the relationship between the play and pause. 6 4 2 3 7 5 1 1 2 3 4 The player has completed the cue or pause operation and is waiting for the play start command. When the PLAY/PAUSE button is pressed and enter play mode is entered. Playing. The pause mode is set when the PLAY/PAUSE button is pressed again. 5 6 7 Figure 6 Pausing.
PAGE 11
9. Scanning (Fast forward/Fast backward) Scanning is a function for moving quickly forward or backward when the or button is pressed. The scanning speed depends on how long you hold the button. Press and hold the or to begin scanning. The disc moves rapidly forward or backward and the sound is output. The current scan point is indicated on the LCD. Press and hold the to scan in the forward scanning, to scan in the reverse scanning. 10.
PAGE 12
. Fader start You have the possibility to start the respective CD player directly from the mixer. Make sure that the Control socket is connected with the respective socket on the mixer. Additionally, the Audio out sockets have to be connected with the Line input sockets of your mixer. Please note that the Fader start function only works with the appropriate mixers. Insert the CD and select the desired track. Start playback from your mixer. 13.
PAGE 13
BEFORE SWITCHING OFF THE POWER When you have finished using the CD player, before switching off the power, be sure that the disc holder had been closed with the OPEN/CLOSE button. CAUTION: Do not forcibly close the disc holder when the power is off. PWER OFF PWER OFF Do not switch off the power when the disc holder is open. Switch off the power after the disc holder has been closed with the OPEN/CLOSE button. COMPACT DISCS 1.
PAGE 14
WARRANTY & RETURN POLICY WARRANTY & RETURN POLICY Warranty Through Stantons authorized dealers around the World, Stanton, or one of Stantons authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purchase.