S T A N T O N MA G N E T I C S , I N C information@stantondj.com + 1 954- 689-8833 w w w . s t a n t o n d j .
IMPORTANT TO SAFETY 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. Read these Instructions Keep these Instructions Heed all Warnings Follow all Instructions Do not use this apparatus near water Clean only with dry cloth Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, hear registers, stoves, or other apparatus (including amplifiers) that produce heat.
LINE VOLTAGE SELECTION M.201 FEATURES 3 band EQ w/ input GAIN control per channel. Power on/off muting. Long-lasting crossfader. M.
M.201 CONTENTS 14) Grounding post - for turntable connection. Always use this connection when using standard turntables with ground cable. (Some turntables like the T.80 / T.120 do not require grounding wire) 15) Phono Inputs – Plug your turntables in here. When these connectors are used, your signal is fed directly to the high-quality RIAA phono pre-amplifiers. Use this position only for turntables. Line level sources will overload the sensitive phono pre-amps and will cause distortion.
QUICK SETUP DIAGRAM Study this setup diagram. Make sure all faders are at "zero" and all devices are off. First, connect all input sources. Next, connect your microphone and monitor headphones. Finally, connect the stereo outputs to the power amplifier(s) and/or audio receivers such as tape decks. Plug your mixer into AC power. Now you are ready to switch everything on. IMPORTANT: Always switch on your audio input sources such as turntables or CD players first, then your mixer, and finally any amplifiers.
SPECIFICATIONS M.201 INPUT / OUTPUT IMPEDANCE & SENSITIVITY: LINE -14dB/10K OHM ±2dB PHONO -50dB /47K OHM ±2dB MIC -60dB /2.2K OHM ±2dB MASTER 1K OHM PHONES 0dB/33 OHM ±2dB (LOAD=32 OHM) MAX.
BEFORE USE *Check that the following parts are included in the package with the main unit: 1) Turntable platter 2) Slip mat 3) 45-rpm adaptor 4) Counterweight 5) 500B cartridge and headshell 6) Operating instructions 7) RCA cables with ground wire 8) Target light 9) AC cord 10) Cloth dust cover *Notes: 1) Do not connect the AC power plug before assembly has been completed. 2) Read this manual carefully before using the unit and be sure to store the manual in a safe place for future reference. T.
T.60 TURNTABLE CONTENTS 1) 2) 3) 4) 5) 6) 7) 8) 9) Start/Stop Button Strobe Dots Slip Mat Center Spindle Power Switch 33/45 Button Target Light Base Pitch Control Slider Headshell Locking Nut 10) 11) 12) 13) 14) 15) 16) 17) Tonearm Arm Rest Counterweight 45-rpm Adaptor Position For Preparing Cartridge Phono Output GND Power Cord Connector PLACEMENT • Do not place the unit in a location where it will be exposed to direct sunlight or near a heating appliance.
CONNECTIONS 1. Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household AC outlet. 2. Connect the unit output terminals to the PHONO jack of your M.201. Output terminals Amplifier (Receiver) L (White) >> L Channel R (Red) >> R Channel GND (Spade) >> GND NOTE: • Be sure to connect the ground terminal firmly to the M.201. • If this connection is not made or is loose, a power source "HUM" will result. OPERATION 1.
SPECIFICATIONS T.60 POWER SOURCE AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A.,Canada,Mexico) AC 220V, 50Hz (For United Arab Emirates,Chile,Argentina) AC 220V, 60Hz (For Philippines) AC 230V, 50Hz (For Europe,New Zealand,South Africa,Singapore,Israel) AC 240V, 50Hz (For Australia,U.K.) POWER CONSUMPTION 7.5 Watts DIMENSIONS 452 (W) x 370 (D) x 86 (H) mm WEIGHT 6.
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WARRANTY Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purchase.
cut along dotted line State Where did you buy this product? Date of Purchase Serial Number Model Number PRODUCT INFO Telephone Country City Address Name PERSONAL INFO Zip If you have internet access, please register your product at www.stantondj.com. Otherwise, return this card completely filled out in order to validate your warranty.
PLACE STAMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A.