RM.
important Safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use the apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9.
contents 1. 2. 3. 4. introduction ................................................................................................................................................................ 1 1.1. Welcome to the RM.416! ............................................................................................................................................... 1 1.2. Overview ............................................................................................................................
introduction 1. introduction 1.1 Welcome to the RM.416! Thank you for purchasing the RM.416. Before starting, please check that you have received the following items: • RM.416 unit • Power Cable • User Manual Now that you have checked that everything was included in the box, let’s talk about the RM.416. 1.2 overview The RM.416 is Stanton’s latest addition to the RM (Rack Mount) series of mixers. With four traditional channels coupled with three microphone inputs the RM.
connecting the RM.416 2. connecting the RM.416 Before starting to connect the RM.416, please read the Important Safety Instructions page and study this setup diagram (Figure 2.1). Make sure all faders are at "zero,” the Master Volume is turned all the way counterclockwise, and all devices are Off. Figure 2.1 Now, please follow these simple instructions: 1. 2. 3. 4. 5. 6. Connect all input sources. Connect your microphone and monitor headphones.
RM.416 Description (Front Panel) 3. RM.416 Description 3.1 Front Panel (Figure 3.1) Figure 3.1 1. Mic gain (gain): These rotary knobs control the output volume of the Mic channels. 2. Mic eQ: These knobs control the frequency response of MIC 1/2 separately. Range -12 dB to +12 dB. HI: Adjusts the High frequencies (centered at 10 kHz). MID: Adjusts the Mid range frequencies (centered at 1 kHz). LOW: Adjusts the Low frequencies (centered at 100 Hz). 3.
RM.416 Description (Front Panel) - continuation 12. Zone (Zone): This knob controls the level of the ZONE output located on the Rear Panel (5). The ZONE level is not affected by the MASTER VOLUME and MASTER BALANCE. The ZONE output is essentially a second Master output and can be used to drive a booth monitor, feed a recorder, or provide audio to a secondary set of PA speakers. 13. Subwoofer (VoluMe): This knob controls the level of the SUBWOOFER output located on the Rear Panel (3). 14.
RM.416 Description (Rear Panel) 3.2 Rear Panel (Figure 3.2) Figure 3.2 1. Power connector (ac in): While the power is switched OFF, plug the included power cord into the mixer first, and then plug it into the outlet. 2. uSB Port (uSB): After hooking up your computer with the USB 1.1 connections, your computer will detect the RM.416 as an external sound card.
troubleshooting 4. troubleshooting Problem / Symptom Possible cause / Solution no Sound. Is the power ON? Based on your connections, check that you have properly set the INPUT SELECTOR SWITCH. Make sure that the GAIN, CHANNEL FADER, and MASTER VOLUME are turned up. Make sure the channels are properly assigned to the crossfader. no Sound-headphones. Check the CUE VOLUME, CUE MIX, and CUE button settings. Mixer sounds noisy.
Specifications Specifications 1. geneRal Section: PRODUCT Professional Mixer POWER SOURCE AC 100 - 240V, 50/60 Hz POWER CONSUMPTION 21 W DIMENSIONS (H x W x D) 136.8 mm x 482 mm x 177 mm WEIGHT 4.5 kg 2. inPut/outPut iMPeDance & SenSitiVitY: (EQ FLAT, MAXIMUM GAIN, CUE MIXING CENTER, LOAD=100 k ohm) 2.1 input impedance and Reference level: Line 20k ohm /-14 dBV +/-0.1 dB (200 mV) Aux 47k ohm /-14 dBV +/-0.1 dB (200 mV) Phono 47k ohm /-50 dBV+/-0.1 dB (2 mV) Mic 1,2,3 10k ohm /-54 dBV+/-0.
Specifications - continuation 9. eQ MIC 1/2 12 +/- 3 dB, -12 +/- 3 dB, at 100 Hz 12 +/- 3 dB, -12 +/- 3 dB, at 1 kHz 12 +/- 3 dB, -12 +/- 3 dB, at 10 kHz MIC 3/CHANNEL 10 +/- 2 dB, below -25 dB at 70 Hz 10 +/-2 dB, below -25 dB at 1 kHz 10 +/-2 dB, below -15 dB at 13 kHz 10. channel Balance Within 3 dB, from 0 to -40 dB 11. FaDeR kill More than 75 dB at 1 kHz for CHANNEL FADER More than 70 dB at 1 kHz for CROSSFADER 12.
notes ........................................................................................................................... ........................................................................................................................... ........................................................................................................................... ........................................................................................................................... .........
Registration card thank you for choosing Stanton! Your satisfaction is extremely important to us. We proudly stand behind the quality of our work and appreciate that you put your trust in us. Registering your product will help us guarantee that you are kept up to date on our latest advances. Warranty Service in the united States: Please contact Stanton Tech Support BEFORE sending your product.
Stanton Warranty Stanton Warranty Through Stanton's authorized dealers around the World, Stanton, or one of Stanton's authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purchase.
-
Copyright © 2009 Stanton Magnetics, Inc. RM.416 and STR8.150, are trademarks or registered trademarks of the Stanton Group. All other trademarks are property of their respective owners, who are in no way affiliated with Stanton DJ or SC System products. All information included in the User Manual is subject to change without notice.
