FULL MANUAL OPERATING INSTRUCTIONS BELT DRIVE TURNTABLE PO W ER T.5O WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
IMPORTANT SAFETY INSTRUCTIONS 1. 2. 3. 4. 5. Read these Instructions – All the safety and operating instructions should be read before this product is operated. Keep these Instructions – The safety and operating instructions should be retained for future reference. Heed all Warnings – All warnings on the appliance and in the operating instructions should be adhered to. Follow all Instructions – All operating and use instructions should be followed.
IMPORTANT SAFETY INSTRUCTIONS 21. Lightning – For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. 22.
NAME OF PARTS 15 14 1 13 2 3 12 4 11 10 9 PO W ER 5 1 6 7 1) 2) 3) 4) 5) 6) 7) 8) 8 Start/Stop Button Strobe Dots Slip Mat Center Spindle Power Switch 33 Button 45 Button Target Light Base 9) 10) 11) 12) 13) 14) 15) 16 17 16) Phono Output 17) GND Pitch Control Slider Headshell Locking Nut Tonearm Arm Rest Counterweight 45-rpm Adaptor Position For Preparing Cartridge 18 18) Power Cord Connector
BEFORE USE *Check following parts included in the package with the main unit: 1) Turntable platter 2) Slip mat 3) 45-rpm adaptor 4) Counterweight 5) 500B cartridge and Headshell, except on model T.50X, no cartridge included. 6) Operating instructions 7) RCA cables with ground wire 8) Target light 9) AC cord 10) Cloth dust cover *Notes: 1) Do not connect the AC power plug before assembly has been completed.
CONNECTIONS 1. Connect the power cord to the auxiliary power outlet on the rear panel of your amplifier or receiver or to a household AC outlet. 2. Connect the unit output terminals to the PHONO jack of your amplifier or receiver. Output terminals Amplifier (Receiver) L (White) >> L Channel R (Red) >> R Channel GND (Spade) >> GND NOTE: • Be sure to connect the ground terminal firmly to the amplifier or receiver. • If this connection is not made or is loose, a power source "HUM" will result. OPERATION 1.
SPECIFICATIONS TONEARM SECTION: Type Effective Arm Length Tracking Force Adjustment Range Applicable Cartridge Weight Static balanced straight shaped tonearm with cardan’s suspension 191mm 0~4g 6~10g CARTRIDGE SECTION: Channel Separation Channel Balance Needle Pressure Range More than 14 dB Within 2.5dB at 1KHz 1.5~2g GENERAL SECTION: Power Supply Power Consumption Dimensions Weight AC 100V, 50/60Hz (For Japan) AC 110V, 60Hz (For Taiwan) AC 120V, 60Hz (For U.S.A.
Stanton Magnetics, Inc. – Warranty Provision – Returns for Repairs or Replacement WARRANTY Through Stanton’s authorized dealers around the World, Stanton, or one of Stanton’s authorized distributors outside the U.S., will, without charge, repair or replace, at the sole discretion of the entity responsible for making the repair or providing the replacement, any Stanton merchandise proved defective in material or workmanship for a period of one (1) year following the date of original purchase.
cut along dotted line State Where did you buy this product? Date of Purchase Serial Number Model Number PRODUCT INFO Telephone Country City Address Name PERSONAL INFO Zip If you have internet access, please register your product at www.stantondj.com. Otherwise, return this card completely filled out in order to validate your warranty.
PLACE STAMP HERE Stanton Magnetics, Inc. 3000 SW 42nd Street Hollywood, FL 33312 U.S.A.
