User's Manual

ManualsBrandsStar Micronics ManualsPrintersStar Micronics Printer TUP500

THERMAL PRINTER

TUP500 SERIES

TECHNICAL MANUAL

[ FIRST

EDITION

]

Summary of content (70 pages)

PAGE 1
THERMAL PRINTER TUP500 SERIES TECHNICAL MANUAL [ FIRST EDITION ]
PAGE 2
NOTICE • All rights reserved. Reproduction of any part of this manual in any form whatsoever, without STAR’s express permission is forbidden. • The contents of this manual are subject to change without notice. • All efforts have been made to ensure the accuracy of the contents of this manual at the time of going to press. However, should any errors be detected, STAR would greatly appreciate being informed of them. • The above notwithstanding, STAR can assume no responsibility for any errors in this manual.
PAGE 3
INTRODUCTION This manual describes the thermal printer TUP500 series. It is designed for use as a reference for periodic inspections and maintenance procedures to be executed by service personnel. It is not intended for the general user. Users of this manual should have a basic knowledge and understanding of the English language. ● This manual is divided into the following sections: Chapter 1 Adjustments Chapter 2 Maintenance and Lubrication Chapter 3 Parts List ● First edition : Feb.
PAGE 4
CHAPTER 1 ADJUSTMENTS This printer has undergone various adjustments so that it will attain a given standard of performance. In this chapter, a brief explanation is given of the methods for making adjustments. Follow the instructions when performing maintenance inspections or when replacing parts to correct malfunctions. 1. Sensor Adjustment ........................................................................2 1.1 Adjustment of the PE/BM Sensor ..........................................................
PAGE 5
1. Sensor Adjustment Presenter Sensor This printer is equipped with the following three paper sensors: PE/BM Sensor • PE(Paper End)/BM(Black Mark) Sensor Detects presence of roll paper and black marks. • NE(Near End) Sensor Detects whether the roll paper is nearing its end. • Presenter Sensor (TUP592 Only) Detects paper in presenter. The aforementioned sensors can be adjusted as follows. NE Sensor 1.1 Adjustment of the PE/BM Sensor 1. Turn the printer off and unplug the power cord. 2.
PAGE 6
4. Set ordinary paper that is not used for black marks, in the PE/BM sensor unit shown below. Use the release lever to open the platen unit (the TUP592 includes presenter unit), insert the paper from the paper insertion inlet and then close the platen unit to set the paper. 5. Turn the power on. The LED on the control panel will flash two times, then the printer will enter the PE/BM sensor adjustment mode. 6. Use a small regular screwdriver to slowly turn the VR1 clockwise, as shown in the drawing below.
PAGE 7
1.2 Adjustment of the NE Sensor (TUP592 Only) 1. Turn the printer off and unplug the power cord. 2. Remove the screws. Then, remove the board chassis. 3. Using the tip of a ballpoint pen or a similar object, set the DIP switches as follows: DSW1-4 OFF, DSW1-5 ON. Screw DIP Switch DSW1 Board chassis 4. Set unused roll paper that will actually be use. 5. Connect the AC adapter and turn the power switch on while pressing switch SW2 on the control panel.
PAGE 8
1.3 Adjustment of the Presenter Sensor 1. Turn the printer off and unplug the power cord. 2. Remove the screws. Then, remove the board chassis. 3. Using the tip of a ballpoint pen or a similar object, set the DIP switches as follows: DSW1-4 OFF, DSW1-5 ON. Screw DIP Switch DSW1 Board chassis 4. Set paper into the presenter portion as shown below. Lift the paper holder and insert the paper. Rotate the knob toward yourself to set the paper perfectly straight.
PAGE 9
5. Connect the AC adapter and turn the power switch on while pressing switch SW1 on the control panel. The LED on the control panel will flash two times, then the printer will enter the presenter sensor adjustment mode. 6. Use a small regular screwdriver to slowly turn the VR3 clockwise, as shown in the drawing below. Adjust this to a position where both LED1 (green) and LED2 (red) light.
PAGE 10
CHAPTER 2 MAINTENANCE AND LUBRICATION 1. 2. Maintenance ............................................................................................ 8 1-1. Cleaning the Thermal Head and Platen .................................................................8 1-2. Handling Paper Jams .............................................................................................9 1-3. How to Release the Cutter Lock .............................................................................
PAGE 11
1. Maintenance In order to maintain the optimum performance of this printer and to prevent trouble, maintenance must be carried out according to the following items. When performing maintenance, always turn off the power, and take the appropriate measures to orevent static electricity. 1-1.Periodic Maintenance To ensure long-term and stable printing, periodically clean the modules. It is recommended that you clean every 3 months or every 500,000 lines.
PAGE 12
1-2.Handling Paper Jams If recording paper should become jammed, open the platen unit (including the presenter unit of TUP592) and remove the jammed paper. Never pull on the jammed paper unnecessary while the printer unit is closed because this can damage the drive system parts. Remove jammed paper according to the following procedures. 1. Open the platen unit using the release lever. 2. Rotate the knob to remove the jammed paper. 3. Close the platen unit.
PAGE 13
2. Lubrication Lubrication is very important to maintain optimum performance and to prevent trouble. 2-1.Lubricant The type of lubricant greatly affects the performance and durability of the printer, especially in a low temperature envi ronment. We recommend use of the grease listed below for this printer. Type of oil Product name Maker Grease Molykote EM-30L Dow Corning Corporation Oil Mobil 1 Mobil Oil Co., Ltd. 2-2.
PAGE 14
5 c 3 4 2 e e c d 1 d 1 Fig.
PAGE 15
CHAPTER 3 PARTS LIST HOw TO USE PARTS LIST (1) (2) (3) (4) (5) (6) (7) DRWG. NO. This column shows the drawing number of the illustration. REVISED EDITION MARK This column shows a revision number. Part that have been added in the revised edition are indicated with “#”. Part that have been abolished in the revised edition are indicated with “*”. #1 : First edition → Second edition *1 : First edition → Second editon PART NO. Parts numbers must be notified when ordering replacement parts.
PAGE 16
1. Printer Assembly 1-1.Disassembly Drawing A.
PAGE 17
B.
PAGE 18
1-2. Parts List DRWG.NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 - REV. Printer Assembly PARTS NO.
PAGE 19
2. Mechanism Base Unit 2-1. Disassembly Drawing A.
PAGE 20
B.
PAGE 21
2-2. Parts List DRWG.NO. 1 2 3 4 5 6 7 8 REV. Mechanism Base Unit PARTS NO. 38400000 39454000 33913000 NPN NPN 04991204 01903090 01903077 01903077 09992102 PARTS NAME TMP592-24 TMP542-24-A HANDLE TUP9 MECHANISM BASE TUP5 WIRE 18UL1007BRN060TT FASTENER T18S SCREW TAT 3-8 CT-FL SCREW TAT 3-5 CT-FL SCREW TAT 3-5 CT-FL SPIRAL TUBE 6.
PAGE 22
3. Printer Mechanism Unit 3-1. Disassembly Drawing A.
PAGE 23
B.
PAGE 24
3-2. Parts List DRWG.NO. 1 2 3 4 5 6 7 REV. Printer Mechanism Unit (TUP592) PARTS NO.
PAGE 25
Printer Mechanism Unit (TUP542) DRWG.NO. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 REV. PARTS NO.
PAGE 26
4. Sub-Assembly 4-1. Frame R Unit 9 4 2 6 3 5 1 DRWG.NO. 9-1 9-2 9-3 9-4 9-5 9-6 REV. PARTS NO. NPN 33210520 30211050 04020016 02010401 01914003 PARTS NAME FRAME R ASSY TUP9 BUSHING TUP9 PF ROLLER BEARING TMP6 STOP RING SE4.
PAGE 27
4-2. Frame L Unit 8- 9 7 5 3 8 2 1 10 4 6 DRWG.NO. 8-1 8-2 8-3 8-4 8-5 8-6 8-7 8-8 8-9 8-10 REV. PARTS NO. NPN 33912000 33210520 30531180 30211050 NPN 04020016 02010401 01914003 01903060 PARTS NAME FRAME L ASSY TUP9 CLAMP TUP9 BUSHING TUP9 CLAMP SPRING TUP9 PF ROLLER BEARING TMP6 PAPER SET SEAL TUP9 STOP RING SE4.
PAGE 28
4-3. Board chassis L Unit 9 6 5 9 A 2 A 9 1 11 11 9 6 7 8 10 9 3 4 DRWG.NO. 6-1 6-2 6-3 6-4 6-5 6-6 6-7 6-8 6-9 6-10 6-11 REV. PARTS NO.
PAGE 29
4-4.
PAGE 30
Presenter Unit PR521 DRWG.NO. 1-1 1-2 1-3 1-4 1-5 1-6 1-7 1-8 1-9 1-10 1-11 1-12 1-13 1-14 1-15 1-16 1-17 1-18 1-19 1-20 1-21 1-22 1-23 1-24 1-25 1-26 1-27 REV. PARTS NO.
PAGE 31
4-5. Paper Guide Unit (PR521) 1- 4 2 1 3 DRWG.NO. 1-4-1 1-4-2 1-4-3 REV. PARTS NO.
PAGE 32
4-6. Guide Frame Unit 1- 7 3 2 1 3 4 DRWG.NO. 1-7-1 1-7-2 1-7-3 1-7-4 REV. PARTS NO.
PAGE 33
4-7. Head Unit 2- 3- 7 2 1 3 5 4 6 DRWG.NO. 2-3-1 2-3-2 2-3-3 2-3-4 2-3-5 2-3-6 2-3-7 REV. PARTS NO.
PAGE 34
4-8. Platen Holder Unit 2- 6 1 4 7 8 6 5 8 3 2 9 DRWG.NO. 2-6-1 2-6-2 2-6-3 2-6-4 2-6-5 2-6-6 2-6-7 2-6-8 2-6-9 REV. PARTS NO. 37413700 NPN NPN NPN 30903100 30211090 04020016 04020010 00926403 PARTS NAME PLATEN ASSY TMP5 BLADE GUIDE TMP10 PLATEN HOLDER TMP5 LOCK SHAFT TMP5 STATIONARY KNIFE KC-GS90 PF ROLLER BEARING TMP5 STOP RING SE4.0 STOP RING SE2.0 SCREW TAT 2.
PAGE 35
4-9. Paper Guide Unit 2- 7 6 1 3 2 10 7 4 5 9 8 11 5 11 DRWG.NO. 2-7-1 2-7-2 2-7-3 2-7-4 2-7-5 2-7-6 2-7-7 2-7-8 2-7-9 2-7-10 2-7-11 REV. PARTS NO. 37417500 33914220 33914210 33100240 33090040 32592140 NPN 04020010 02303025 01902028 00920603 PARTS NAME PE DETECTOR ASSY TMP5 SIDE GUIDE R TMP5 SIDE GUIDE L TMP5 GUIDE PINION 18X0.5 TMP9 RACK TMP5 GROUND SPRING TMP5 PAPER GUIDE ASSY TMP5 STOP RING SE2.0 POLY-SLIDER WP3X0.
PAGE 36
5.
PAGE 37
R161 R163 BC03 0.022U VDD:3.3V RES VDD:3.3V VDD:3.3V PRS0 MNE MBM PRS3 PRS2 PRS1 MHDTH MPE VM NC VSS DS VDD OUT 1 4 R162 IC03 S-80130BNMC 3 2 5 SW1 SKHHAL 10K C113 0.022U 4.7K C109 1000P R142 ZD02 C3V9S R138 VDD:3.3V C114 0.022U VDD:3.3V 4.7K_F R137 R164 20K_F R134 4.7K RA12 10K X 4 VDD:3.3V DSW1 219-10LPSTRF SW2 SKHHAL 10K ZD01 HZU20B2 VDD:3.3V RA10 10K X 4 1.5K 1K R113 R104 R143 R129 VDD:3.3V C107 0.1U R150 R151 R152 1.
PAGE 38
Main Logic Board 2/5 10K R235 10K R234 10K 10K R231 10K R230 10K R229 Red Yellowish green Red Power Error Power Error LED1 LED2 LED3 LED4 Green USAGE LED Main Logic Board Operation Panel 10K R236 COLOR 10K R233 R232 LED SPECIFICATION PRM1 DKEXT1 DKEXT2 PRM2 ACDS1 ACDS2 PFMPH1 PFMPH2 PFMPH3 PFMPH4 PFMI0 PFMI1 10K R237 5VDRV 10K R238 RES PNLSW2 PNLSW1 DKSIG1 MHDUP OPTSNS DKSIG2 ACSW1 ACSW2 GACLKIN GAHDON GALFCK GAINTHDSD GAIO3V0 GAIO3V2 GAINTIFIO10 VDD:3.
PAGE 39
Main Logic Board 3/5 - 36 AB[21..0] CS1 LWR HWR RD CS2 RES FPVPP DB[15..0] R306 Memory 2M+2M 4M+4M Parts No. IC07+IC08 ** 0R ** ** 0R R307 R308 0R R306 ** 0R R309 0R OE WE CE1 CE2 A16 A17 GND VCC 24 8 IC07 LP62S2048AX-55LLI 21 A0 IO1 22 IO2 23 A1 IO3 25 A2 IO4 A3 A4 26 A5 IO5 27 IO6 28 A6 IO7 29 A7 IO8 A8 A9 A10 A11 A12 A13 A14 A15 0.1U BC07 VDD:3.3V DB4 DB5 DB6 DB7 DB0 DB1 DB2 DB3 R307 R309 VDD:3.3V < Support of manufactured by SHARP FROM (Usually:Intel) > Parts No.
PAGE 40
Main Logic Board 4/5 5VDRV 5VDRV PNLSW1 PNLSW2 PNLLED1 PNLLED2 ACSW1 ACSW2 ACDS1 ACDS2 [L:0.8V,H:2.0V] MBM MPE MHDUP PFMI0 PFMI1 PFMPH1 PFMPH2 PFMPH3 PFMPH4 R433 R434 NC NC NC C417 0.022U 0.022U 0.022U 0.022U C418 C415 0.022U C411 VR_68K 4.7K VR2 VR_68K VR1 4.
PAGE 41
Main Logic Board 5/5 GND GND 1 4 EXP1 EXP0 DKSIG2 DKSIG1 DKEXT2 DKEXT1 VDD:3.3V VDD:3.3V + R566 4.7K R567 1 1 VDD:3.3V R557 R556 VM 2 2 M-GND C524 0.022U 10K 10K 3 3 1 GND R542 20K 330 330 330 R553 R554 R555 F6 TF16SN0.50TTD 330 R552 M-GND F7 TF16SN2.00TTD C525 10U_50V + MNE VM 8 R528 10K_2125 GND SIG1 SIG2 SIG3 GND MM+ VCC + VR6 C540 **C J3 1 C538 1U_50V_2125 R527 JUMPER1_0 2 R549 100K C528 0.1U 0R_2125 F4 **TF16SN2.
PAGE 42
6-2.
PAGE 43
6-3.
PAGE 44
6-4. Parts List DRWG.NO. BC01A-01F BC02-03 BC04A-04F BC05 BC06A-08 BC09A BC09B-10A BC10A BC10B BC13A BC13B C107 C109 C111-112 C113-114 C115 C201 C401 C404 C405-406 C406 C407-409 C410 C411 C412 C413-418 C508 C517 C518 C519 C520 C521 C522 C524 C525 C527 C528 C532-534 C535 C536-537 C538 CN11 CN21 CN22 CN23 CN31 CN32 CN33 CN34 CN41 CN42 D1-4 D5 REV. Main Logic Board PARTS NO.
PAGE 45
Main Logic Board DRWG.NO. D8 DSW1 DSW2 F3 F6 F7 FB401 IC01 IC02 IC03 IC04 IC05 IC06 IC07-08 IC09 IC10 IC11 IC12 IC13 L1 LED1 LED2 Q1 Q3 R101-103 R104-106 R107 R108-111 R113 R114 R115 R116 R117 R118-121 R122 R123-125 R126-128 R130 R131 R132 R133 R134 R135-136 R137 R138 R139 R142-143 R145 R146 R148-149 R150-152 R161 REV. PARTS NO.
PAGE 46
Main Logic Board DRWG.NO. R162 R163 R164 R165 R166-167 R168 R201-207 R207 R208-210 R211 R212-213 R214 R215 R216 R217-218 R219-220 R221 R222-238 R241-242 R249 R251-252 R304 R308-309 R311 R401 R402 R403 R404 R405-406 R407 R408 R409 R412 R413 R414 R415-417 R418 R419 R420 R421-424 R425 R426 R427 R428-429 R430-431 R432 R433-434 R435 R436 R437 R439 R440 REV. PARTS NO.
PAGE 47
Main Logic Board DRWG.NO. R442 R443 R444-445 R446 R447 R448 R449 R452 R454 R504-505 R512 R513 R519 R520 R521 R523 R527 R528 R529 R530 R536-539 R541 R542 R548 R549 R551 R552-555 R556-557 R558 R559 R560 R562 R564 R565 R567 R568 R569 R570 R571-572 R574 R575 R576 R579 R580 RA01-09 RA10 RA11 RA12-15 RA16 SW1-2 TR06 TR07 REV. PARTS NO.
PAGE 48
Main Logic Board DRWG.NO. TR08 VR1-2 VR3 VR6 XTAL1 ZD01 ZD02 ZD03 ZD05 ZD07 ZD08 - REV. PARTS NO. NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN PARTS NAME CHIP TRANSISTOR KTC3875S-G*AL RP CHIP RESISTOR EVM3S-68K RP CHIP RESISTOR EVM3S-47K RP CHIP RESISTOR EVM3S-47K CERA.
PAGE 49
7. Sub Board 7-1. Circuit Diagram SW1 SF-W1P1A-03BB CN1 TCS7960-53-2010 1 +24V GND N.C. F-GND F1 MRT_3.15A_250V 1 2 2 3 1 4 1 2 J1 STP122 2 F-GND CN2 51036-0200 +24V GND CN3 **51036-0200 SWA SWB The part marked with two asterisks (**) is not mounted. 部品名が｛**..｝のパ－ツは未実装 7-2. Component Layou 7-3. Parts List DRWG.NO. CN1 CN2 F1 J1 SW1 REV. Sub Board PARTS NO. NPN NPN NPN NPN NPN PARTS NAME CONNECTOR TCS7960-53-2010 CABLE UNIT 2X60CC TSP8 FUSE MRT3.
PAGE 50
8. Control Panel Board 8-1. Circuit Diagram 8-2. Component Layout 8-3. Parts List DRWG.NO. CN1 LED1 LED2 R1-2 SW1-2 - REV. Control Panel Board PARTS NO.
PAGE 51
9. Snout Board 9-1. Circuit Diagram LED2 LED1 LED3 LED4 PAD1 24V PAD2 M-GND PAD3 OUT1 PAD4 OUT2 **LED **LED **LED **LED LED9 LED10 LED11 LED12 SML-E12UW OUT1(Green) : LED5-8,13-16 Control SML-E12UW LED6 LED5 SML-E12UW SML-E12UW LED8 LED7 OUT2(Red) : LED1-4,9-10 Control **LED **LED **LED **LED LED13 LED14 LED15 LED16 SML312ECT SML312ECT SML312ECT R2 1K_6331 R1 1K_6331 SML312ECT TR1 KTC3875 TR2 KTC3875 The part部品名が｛**..
PAGE 52
10. Serial Interface Board (25pin) 10-1.
PAGE 53
10-2. Parts List DRWG.NO. C1 C2 C3-6 C7-8 C9 CN1 CN2 D1-2 D3 D4-5 DSW1 IC1 IC2 L1-7 L8 L9 R1-2 R3-4 R5-6 R7 R8 R9 R10 R11-12 R13 R14-15 R16 R17 R18 R19-20 R21 R22 R23 R24 RA1 TR1 TR2 TR3 TR4 TR5 TR6 REV. Serial Interface Board (25pin) PARTS NO. NPN NPN NPN NPN NPN NPN NPN NPN NPN PARTS NAME CHEM. CAPA. 1UF 50V CERA.CAPA.CHIP1608 0.022UF 50V CHEM. CAPA. 1UF 50V CERA.CAPA.CHIP1608 0.022UF 50V CERA.CAPA.CHIP1608 0.
PAGE 54
11. Serial Interface Board (9pin) 11-1.
PAGE 55
11-2. Parts List DRWG.NO. C1 C2 C3-6 C26-35 R1-2 R4-5 R6-7 R8 R11-13 RA1 IC1 IC2-3 IC4 L1-7 L8-9 DSW1 CN1 CN2 CN3 REV. Serial Interface Board (9pin) PARTS NO. NPN NPN NPN PARTS NAME CHEM. CAPA. 1UF 50V CERA.CAPA.CHIP1608 0.022UF 50V CERA.CAPA.CHIP1608 0.1UF 25V Q' TY 1 1 4 REMARKS RANK NOT MOUNTED NPN NPN CHIP RESISTOR 10 K-OHM 1/16W CHIP RESISTOR 10 K-OHM 1/16W 2 2 NPN NPN NPN 08200213 CHIP RESISTOR 0 OHM 1/16W CHIP RESISTOR 10 K-OHM 1/16W RESIS.
PAGE 56
12. Parallel Interface Board 12-1.
PAGE 57
12-2. Parts List DRWG.NO. BC1-3 C1 C2 C3-4 C5 CN1 CN2 IC1 IC2 IC3 L1-2 L3-6 L7 L8-10 R1 R2-9 R10 R11 R12 R13 R14 R15 R16 R17 R18 R19-20 R21 R22 R23 R24 R25 RA1 RA2 TR1 REV. Parallel Interface Board PARTS NO. NPN PARTS NAME CERA.CAPA.CHIP1608 0.022UF 50V Q' TY 3 NPN CERA.CAPA.CHIP1608 1000PF 50V 1 NPN NPN NPN 08211042 NPN 08210126 NPN 09990754 NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN CHEM. CAPA.
PAGE 58
S-GND S-GND S-GND S-GND ID0 ID1 ID2 +5V +5V I/O0 I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 CS RD WR BUSY I/O9 TXD RXD ERR SEL POUT ACK I/O8 STB I/O10 INIT CD4 CD5 CD6 CD7 CD0 CD1 CD2 CD3 ZD3 C12 GND 100 100 10k STBB 5 GND CD 6 VCC C01 0.22u_K GND C02 0.022u GND B20 A20 A3 B15 A1 B1 A2 A9 B9 A16 B16 A17 B17 A18 B18 A19 B19 B14 B13 A15 0R_2125 L3 **220p M-HOLE + VCC PCB1B 0R_2125 GND GND C03 4.
PAGE 59
13-2.
PAGE 60
13-3. Parts List DRWG.NO. BC1 BC2A BC2B BC2C BC4-5 C01 C02 C03 C04 C05 C06 C07 C08 C09-10 C13 C14 CN1 CN2 IC1 IC2 IC4 IC5 JP2 JP5 L1-3 L6-7 R01 R02-09 R13 R14 R15-16 R17 R18 R19 R21 R22-26 R27 R29-31 RA01 RA02 RA05 TR1 TR2 XTAL ZD1 ZD4 - REV. USB Interface Board PARTS NO. NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN PARTS NAME CERA.CAPA.CHIP1608 0.
PAGE 61
- 58 - 3 2 1 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 sh4 1 18 17 16 15 14 13 12 sh2 DEBUG_P0 DEBUG_P1 DEBUG_P2 DEBUG_P3 sh2 sh2 sh2 sh2 DETECT_SUB sh2 DEBUG_RXD 3 U10C 8 5 4 74ALVC2G04 P15 M14 M12 TL49 M15 L13 N15 2 10k D6 2 10k 2 10k C8 D8 2 820 2 820 A8 2 820 11 TL:Locate solder side 1 R117 1 R118 1 R56 1 R55 1 R125 1 R57 A10 R1 M3 N2 P1 M13 VCC 6 4 VCC A3 A2 A1 A0 R3 R2 M4 N4 M5 P5 N5 R4 R6 M6 P6 N6 P8 M7 R7 N7 N9 R9 M9 N8
PAGE 62
Ethernet Interface Board 2/5 1 2 C1 2.2u 1 VIN U2 1 R128 GND 2 +5V 3 1 R11 1 R10 L88M33T VOUT 2 (0/2125) (0/2125) 2 2 33 1 2 + PC2 C2 100u C4 470p TP3 LC-4 3 2 1 TP12 LC-4 NC VOUT S-1165B15 ON/OFF GND VIN U3 VCC MOUNT_PAD On the chassis fixing area MOUNT_PAD 1 2 PC1 4 5 + C3 22u 1 R116 1.5V C21 470p 2 (0/2125) MII_CRS MII_RXCLK MII_RXD3 MII_RXD2 MII_RXD1 MII_RXD0 MII_RXER MII_RXDV sh5 sh5 sh5 sh5 sh5 sh5 sh5 sh5 C9 0.1u C10 0.1u MII_COL sh5 1.
PAGE 63
Ethernet Interface Board 3/5 A[22..0] sh1 9 9 15 15 - 12 - 12 sh1 CS1 BE[3..2] sh1 WP CAS[3..0] WE sh1 R133 1 R134 1 1 R132 1 sh1 OE CS0 CS0WE CS0OE R131 *A20 is for 32M. WP VccQ - - 47 Vpp 13 - 13 BYTE 47 47 - RYBY 15 A21 (Not Used) A20 10 10 10 A19 BJE 29A L C3 sh1 sh1 D[15..
PAGE 64
Ethernet Interface Board 4/5 D4 3 D2 D3 (Green) 1 (Orange) 1 2 2 (DF2S5.6S) 2 D7 (DF2S5.6S) 2 D6 1 1 MAX3208 GND NC2 NC1 IO2 IO1 Left (view from outside) Right (view from outside) VCC 4 10 5 2 1 9 8 7 6 5 IO4 9 2.5V VCC NC4 NC3 IO3 8 C39 0.1u 10 7 6 1 R4 2 470 1 R7 L2 RX- CT2 C41 0.1u 2.5V_A PLD_OUT2 PLD_OUT1 RX+ TX- CT1 TX+ C40 10u/2125 sh4 sh4 H1260 8 7 6 3 2 1 FB3 BK1608 RD- RDCT RD+ TD- TDCT TD+ C37 0.1u 2.5V_A C38 0.1u 2.
PAGE 65
Ethernet Interface Board 5/5 - 62 IF_CD4 IF_CD6 sh4 sh4 sh4 +5V 1 R78 2 10k A14 IF_1284 2 10k A13 IF_STB 1 A12 IF_BUSY R77 A11 A20 A19 A18 A17 A16 A15 A10 IF_SEL A9 A8 A7 A6 A5 IF_ERR SUB_ID1 +5V IF_CD2 sh4 IF_HOST_BUSY IF_CD0 sh4 A4 A3 A2 A1 GND I/O6(SUB_ID1) I/O4 I/O2 I/O0 WE GND I/O7(SUB_ID2) I/O5(SUB_ID0) I/O3 I/O1 GND CS RD ACK POUT INIT +5V I/O9 CD7 CD5 CD3 CD1 RXD TXD ID1 PHEC40P-R111/ R211 I/O10(SIN/1284ACTIVE) STB BUSY SEL
PAGE 66
14-2.
PAGE 67
14-3. Parts List DRWG.NO. C1 C2 C3 C4 C5 C6 C7 C8-17 C18 C19-20 C21-23 C24-C25 C26 C27 C28-30 C31 C32-35 C36 C37-39 C40 C41-42 C43-44 C45-46 C47-C50 C51 C52-53 C54 RA1-RA17 RA18 RA19-24 R1-3 R4 R5-6 R7 R8-9 R10 R11 R12-13 R14 R15 R16-R28 R29 R30-R35 R36 R37 R38 R39 R40-41 R42-43 R44 R45 R46 REV. Ethernet Interface Board PARTS NO. NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN NPN PARTS NAME CERA.CAPA.CHIP1608 2.2UF 6.3V CHEM.CAPA.CHIP 100UF 6.3V CHEM.CAPA.CHIP 22UF 6.3V CERA.CAPA.CHIP1608 470PF 50V CERA.CAPA.
PAGE 68
Ethernet Interface Board DRWG.NO. R47 R48 R49 R50 R51 R52 R53 R54 R55-57 R58 R59 R60 R61-R64 R65-66 R67-68 R69 R70 R71-R76 R77 R78 R79 R80 R81-R82 R83-84 R85-86 R87 R88-89 R90-R92 R93 R94-R99 R100 R101 R102 R103 R104-R106 R107-108 R109-115 R116 R117-119 R120 R121 R122 R123 R124 R125 R126 R127 R128 R129 R130 R131 R132 REV. PARTS NO.
PAGE 69
Ethernet Interface Board DRWG.NO. R133-134 D1 D2 D3 D4-5 D6-7 TR1 TR2 U1 U2 U3 U4 U5 U6 U7 U8 U9 U10 U11 SW1 CN1 CN2 CN3 CN4 X1 X2 JP1 FB1-3 L1 L2 L3-L5 TP1-12 REV. PARTS NO.
PAGE 70
OVERSEAS SUBSIDIARY COMPANIES STAR MICRONICS AMERICA, INC. 1150 King Georges Post Road, Edison, NJ 08837-3729 U.S.A. Tel: (int+1)-732-623-5555, Fax: (int+1)-732-623-5590 ELECTRONIC PRODUCTS DIVISION STAR MICRONICS CO., LTD. 536 Nanatsushinya, Shimizu-ku, Shizuoka, 424-0066 Japan Tel: (int+81)-54-347-0112, Fax: (int+81)-54-347-0409 Please access the following URL http://www.star-m.jp/eng/dl/dl02.htm for the latest revision of the manual. STAR MICRONICS EUROPE LTD.