Product Manual B

1
© 2011. All rights reserved.
ATTENTION: READ CAREFULLY BEFORE ATTEMPTING TO INSTALL OR OPERATE YOUR PUMP. PROTECT YOURSELF AND OTHERS BY
OBSERVING ALL SAFETY INFORMATION AND ADDITIONAL INSTRUCTIONS INCLUDED WITH EQUIPMENT. FAILURE TO COMPLY WITH
INSTRUCTIONS COULD RESULT IN PERSONAL INJURY AND/OR PROPERTY DAMAGE! RETAIN FOR FUTURE REFERENCE.
FW0269
0811
Supersedes
0611
INSTALLATION INSTRUCTIONS
These installation instructions are applicable for
Models HPP360, HPP12V and 473707 Portable Utility Pumps
Notice to Installer: Instructions must remain with installation.
Product information presented
here reects conditions at time of
publication. Consult factory regarding
discrepancies or inconsistencies.
MAIL TO: 95 North Oak Street • Kendallville, IN 46755
[phone] • 1 [phone] • FAX [phone]
1. Make certain that the power source conforms to the requirements of
the equipment as stated on the product nameplates.
2. Check hoses for weak or worn conditions before use and make certain
that all connections are secure.
3. Periodically inspect the pump for damage and perform routine
maintenance as required.
4. The maximum temperature of the pumped liquid must not exceed
130 deg. F. The minimum allowable temperature is 40 deg. F.
5. Use a screen or strainer on the inlet to prevent solids from entering
the pump.
6. NOTE: Pumps with the UL mark are certied by UL and tested to
UL standard UL778. Pumps with the CSA mark are certied by CSA
to CSA standard C22.2 No.108. Pumps with the cCSAus mark are
certied by CSA to CSA standard C22.2 No.108 and UL standard
UL778.
PREINSTALLATION CHECKLIST - ALL INSTALLATIONS
SEE BELOW FOR LIST OF WARNINGS
SEE BELOW FOR LIST OF CAUTIONS
Quality Products Since 1866
Garden Hose
Centrifugal Pump
1. Make sure that the pump is plugged into a
properly grounded electrical receptacle. Use an
Underwriters Laboratory listed circuit analyzer to
test for proper installation of the circuit and ground.
Any service to circuits or receptacles should be
conducted by a qualified licensed electrician.
2. Do not remove the ground pin from the plug
under any circumstances. If the ground pin is dam-
aged, replace the power cord or plug before use.
3.
All electrical installations must conform to the
requirements of the National Electric Code and all
local codes.
4.
It is strongly recommended that the 115 volt units
(Models HPP360 and 473707) be plugged into a
G.F.I. protected circuit.
5.
Disconnect power before servicing the pump
or motor. For Model HPP12V, remove both bat-
tery clips from the battery. For Models HPP360
and 473707, unplug the unit from the outlet.
6.
Do not touch the motor when operating and
allow the motor to cool before touching it after-
wards.
7. This pump is designed for water only. It has not been evalu-
ated for pumping of chemicals.
8.
Do not use this product to pump flammable or
explosive liquids.
9.
Do not use this product in hazardous environ-
ments or anywhere a spark could potentially
ignite explosive gases.
10.
Do not handle this product with wet hands or
while standing in water or on a wet or damp sur-
face.
11. Models HPP360 and 473707 are supplied with an auto-
matically resetting thermal overload device and can
restart without warning.
12.
Do not submerge the pump or motor in water.
13. Secure the discharge line before starting the pump. An
unsecured hose can whip, possibly causing personal
injury or property damage.
14.
Provide a means of pressure relief if the pump
dis-charge can be shut off or obstructed.
Pumps operat-ing against a closed discharge
can create very hot pumped liquid, which can
cause burns.
15. Do not operate this product while unattended.
16. Risk of electric shock - These pumps have not been
investigated for use in swimming pool areas.
17.
This product contains chemicals known to
the State of California to cause cancer and birth defects
or other reproductive harm.