User Manual

ManualsBrandsStar Water Systems ManualsPumpsS1104

DRAINMAKER

INSTALLATION IN STRUC TIONS

PREINSTALLATION CHECK LIST

1. To reduce the risk of elec tri cal shock, a prop er ly ground ed

receptacle of grounding type must be in stalled and pro tect ed

by a ground fault circuit in ter rupt er (GFCI) and in ac cor dance

with National Electrical Code and lo cal codes.

2. Make certain that the receptacle is with in the reach of the pump’s

pow er supply cord. DO NOT USE AN EX TEN SION CORD.

Extension cords that are too long or too light do not deliver

suf ﬁ cient voltage to the pump motor. But more im por tant, they

could present a safety hazard if the insulation were to become

damaged or the con nec tion end were to fall into the sump.

3. Testing for Ground. As a safety mea sure, each elec tri cal outlet

should be checked for ground using an Un der writ ers Lab o ra to ry

Listed circuit analyzer which will in di cate if the pow er, neutral

and ground wires are correctly con nect ed to your out let. If they

are not, call a qualiﬁ ed elec tri cian.

4. For Added Safety. Pump must be con nect ed to a 3-prong

ground ed outlet in ter rupt er de vice (ground fault cir cuit in ter -

rupt er).

5. FOR YOUR PROTECTION, ALWAYS DIS CON NECT PUMP

FROM ITS POWER SOURCE BEFORE HAN DLING. Sin gle

phase pumps are supplied with a 3-prong ground ed plug to help

protect you against the pos si bil i ty of elec tri cal shock. DO NOT,

UNDER ANY CIR CUM STANC ES, RE MOVE THE GROUND

PIN. To re duce the risk of electrical shock, a properly grounded

re cep ta cle of ground ing type must be installed and pro tect ed

by a ground fault circuit interrupter (GFCI) in ac cor dance with

national elec tri cal code and local codes.

6. Installation and checking of electrical cir cuits and hard ware

should only be performed by a qualiﬁ ed licensed electrician.

7. Risk of electric shock - These pumps have not been in ves ti gat ed

for use in swimming pool areas.

8. According to the state of California (Prop 65), this product

contains chemicals known to the state of California to cause

cancer and birth defects or other reproductive harm.

1. Check to be sure your power source is adequate for handling

the voltage requirements of the motor, as in di cat ed on the

pump or basin plate.

2. Make sure the pump electrical supply cir cuit is equipped with

fuses or circuit breakers of proper ca pac i ty. A sep a rate branch

circuit is rec om mend ed, sized ac cord ing to the National Elec-

tri cal Code for the current shown on the pump name plate.

3. All plumbing (discharge and vent lines) must be in stalled to

meet local codes. Unit must be vented. DO NOT USE AN

AU TO MAT IC PLUMBING VENT DEVICE SIM I LAR TO A

"PRO-VENT". Some states require this product to be installed

by a licensed plumb er.

4. Repair and service should be performed by an au tho rized

service station only.

5. CHECK VALVE MUST BE USED TO RE DUCE UN NEC -

ES SARY CYCLING OF PUMP. Check valve must be pur-

chased sep a rate ly.

6. Dewatering pumps are not designed or intended for han dling

raw sewage.

7. Maximum operating temperature must not exceed 77°F

(25°C).

8. For health reasons, do not unplug, turn off, or disable pump

and use pump tank system as a way to ﬁ ll up a sink or laundry

tray, etc.

9. Unit is designed for above ground installation only.

NOTE: Pumps with the “UL” mark and pumps with the “US” mark

are tested to UL Standard UL778. CSA Certiﬁ ed pumps are

certiﬁ ed to CSA Standard C22.2 No. 108.

Notice to Installer: Instructions must remain with installation.

Product information presented here re ﬂ ects con di tions at time of publication. Consult factory re gard ing dis crep an cies or in con sis ten cies.

FW0107

1104

Supersedes

0704

Manufacturers of . . .

“Quality Products since 1866”

95 N. Oak St. • Kendallville, IN 46755

1-800-345-9422

MODEL:_______________________

DATE CODE: __________________

DATE INSTALLED: _____________

1. Inspect your unit. Occasionally, prod ucts are dam aged during ship ment. If the unit is damaged, contact your dealer before using.

Do Not remove the test plug from the pump.

2. Carefully read the literature provided to familiarize yourself with speciﬁ c details regarding installation and use. These materials should

be re tained for future reference.

SEE BELOW FOR LIST OF WARNINGS

SEE BELOW FOR LIST OF CAUTIONS

Summary of content (8 pages)

PAGE 1
FW0107 1104 Supersedes 0704 Manufacturers of . . . “Quality Products since 1866” 95 N. Oak St. • Kendallville, IN 46755 1-800-345-9422 DRAINMAKER MODEL:_______________________ DATE CODE: __________________ DATE INSTALLED: _____________ INSTALLATION INSTRUCTIONS PREINSTALLATION CHECKLIST Notice to Installer: Instructions must remain with installation. 1. Inspect your unit. Occasionally, products are damaged during shipment. If the unit is damaged, contact your dealer before using.
PAGE 2
Ten Helpful Hints For Easy Installation 1. Read all instructions before beginning installation. 7. Always provide some means to disconnect basin from plumbing for maintenance purposes. 2. Be certain that basin is on a firm level surface. 8. Run unit at least once a month to verify proper operation. 3. Do not use an automatic plumbing vent device. 4. Do not over-torque lid attachment screws. 9. The model number and date code can be found on the lid warning label. 5.
PAGE 3
STEP 1 Determine Installation Configuration NOTE: The basin is designed to be installed directly under the sink (Internal Trap) or on the side (standard) IMPORTANT! Check local and state codes before using the internal trap option. 1.1) Figure 1.1A and 1.1B are typical configurations for installation of the drain systems. The actual configuration will vary depending on your cabinet and sink configuration. NOTE: If installing the internal trap, record the “x” dimension, it will be required in Step 4.
PAGE 4
STEP 2A Installation of the Float Assembly 2A.1) Install the float as shown in Figure 2A.1 and Figure 2A.2. IMPORTANT! FLOAT MUST BE TETHERED IN THE ORIENTATION SHOWN IN FIGURE 2A.2. Water stream will be visible from this hole during pump run periods. WEEP HOLE DISCHARGE PIPE CAP 2 1/4" DRILL 3/16" THRU HOLE CAP DISCHARGE PIPE 6" DRILL Figure 2A.1 STEP 3 SK2009 Figure 2A.2 Installation of the Foam Gasket 3.
PAGE 5
STEP 4 Internal Trap Installation Only 4.1) Cut the tailpipe to the dimension determined in Figure 4.1. 4.2) Install the sink drain components to the lid as shown in Figure 4.2. 4.3) Orient the lid assembly as shown in Figure 4.3 and secure the trap components. (HAND TIGHTEN the assembly to the lid at this time. Adjustment will be required in Step 5.) Note: To insure a proper water seal, the extension must be installed as shown in the “trap detail”. INTERNAL TRAP COMPONENTS SUPPLIED BY OTHERS.
PAGE 6
STEP 5 Final Assembly NOTE: External plumbing configuration will vary depending on the location of basin, location of main stack and available space. 5.1) Place the pump in the basin as shown in Figure 5.1. NOTE: If installing the internal trap, rotate the tail pipe to the orientation shown in Figure 5.1. 5.2) Install the lid components as shown in Figure 5.2. NOTE: Pull excess cordage through the opening and install the cordseal as shown in Figure 5.3A. Ensure o-ring is in the cap before installation. 5.
PAGE 7
Illustrated Parts Breakdown 9 6 10 11 CHECK VALVE (PURCHASED SEPARATELY) 8 5 4 1 15 14 7 12 13 3 2 SK2008 ITEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 DESCRIPTION Drain Pump Md. "WM1048" Basin - Tank Discharge Tube Basin - Lid Hardware Pack Basin Seal Unicheck ¼ - 20X1" lg. RHM Screw S.S. ¼ - Flat Washer S.S. ¼ - 20 Hex. Hd. Nut - S.S. Pipe Cap w/o-ring O-Ring Nylon Cable Tie 5/16” Self Tapping Screw#10x.
PAGE 8
Service Checklist ELECTRICAL PRECAUTIONS- Before servicing a pump, always shut off the main power breaker and then unplug the pump - making sure you are not standing in water and wearing insulated protective sole shoes. Under flooded conditions, contact your local electric company or a qualified licensed electrician for disconnecting electrical service prior to pump removal.