22” 2.4HP 45CC WOOD CUTTING CHAINSAW ITEM: 82100 OWNER’S MANUAL AND SAFETY INSTRUCTIONS SAVE THIS MANUAL: KEEP THIS MANUAL FOR SAFETY WARNINGS, PRECAUTIONS, ASSEMBLY, OPERATING, INSPECTION, MAINTENANCE AND CLEANING PROCEDURES.
IMPORTANT SAFETY INFORMATION GENERAL SAFETY WARNINGS Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. SAFETY The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur.
IMPORTANT SAFETY INFORMATION Make sure the area in which you are cutting is free from obstructions. Do not let the nose of the guide bar contact a log, branch, or any other obstruction while you are operating the saw. Only use replacement bars and chains specified by the manufacturer or the equivalent. Maintain a firm grip at all times, but do not squeeze the handles with constant, excessive pressures. Take frequent breaks. Warning: Always stop the engine before putting a chainsaw down or carrying it.
IMPORTANT SAFETY INFORMATION The engine of this chainsaw is designed to run on a mixed fuel which contains highly flammable gasoline. Never store cans of fuel or refill the fuel tank in any place where there is a broiler, stove, fire, electrical sparks, welding sparks or any other source of heat or fire which may ignite the fuel. Smoking while operating the chainsaw or refilling its fuel tank is extremely dangerous. Always keep lit cigarettes away from the chainsaw at all times.
FEATURES AND ASSEMBLY DIMENSIONS L x W x H: 21” (L) x 13” (W) x 12” (H) DESCRIPTION This aluminum gasoline chainsaw is ideal for cutting and felling. It adopts the automatic brake system with wide designed front hand guard, which is able to reduce injury during operating. The anti-kickback chain decreases the probability of kick back, which increases safety. In addition, it also can be used under extreme environment with long life due to aluminum solid protection.
ASSEMBLY AND OPERATION GUIDE BAR AND SAW CHAIN PARTS LIST A standard chainsaw unit package contains the items illustration in Figure F1. Open the box and install the guide bar and the saw chain on the power unit as follows. 1. Power Unit 2. Bar Protector 3. Guide Bar 4. Chainsaw 5. Plug Wrench 6. Screwdriver for Carburetor Adjustment 7.
ASSEMBLY AND OPERATION FUEL AND CHAIN OIL Mix gasoline (leaded or unleaded, alcohol-free) and quality proven 2-stroke motor oil (FC grade) for air cooled 2-cycle engines. Most engine troubles are caused, directly or indirectly, by the fuel used on the machine. Take special care not to mix a motor oil for 4-cycle engines. Chain Oil: Use motor oil SAE#10W-30 all year round or SAE#30-#40 in colder temperatures STARTING THE ENGINE 1. Fill the fuel and chain oil tanks respectively and tighten the caps securely.
ASSEMBLY AND OPERATION (1) Chain Oil: The chain oil flow can be changed by inserting a screwdriver in the hole on the bottom of the clutch side. Adjust according to your work conditions. (F13) NOTE: The oil tank should become nearly empty by the time fuel is used up. Be sure to refill the oil tank every time when refueling the unit. ADJUSTING THE CARBURETOR The carburetor on your unit has been factory adjusted but may require fine tuning due to changes in operating conditions.
ASSEMBLY AND OPERATION Stopping The Engine: Note: Before stopping the engine, keep the engine idling for 1 to 2 minutes. 1. Release the throttle lever to allow the engine idling for a few minutes. 2. Put the switch to the “O” (Stop) position (F17) ADJUSTING THE CARBURETOR It is recommended to first practice sawing easy logs. This also helps to get accustomed to your unit. Always follow the safety regultaions. The chainsaw must only be used for cutting wood.
ASSEMBLY AND OPERATION Sprocket (F30): Check for cracks as well as for excessive wear interfering with the chain drive. If the wearing is found, replace it with a new one. Never fit a new chain on a worn sprocket nor a worn chain on a new sprocket. (1) Sprocket (2) Needle Bearing (3) Clutch Drum (4) Spacer (5) Clutch Shoe Fuel Filter: Disassemble the filter and wash with gasoline or replace with a new one. Oil Filter: Disassemble the filter and wash with gasoline or replace with a new one.
MAINTENANCE AND CARE BREAK DOWN ANALYSIS GUIDE 10
MAINTENANCE AND CARE CARE AND MAINTENANCE 11
QUICK START GUIDE 1. Lay out your tools 2. Mix the oil 3. Check that the chain brake is in the unlocked position by pulling the front hand guard toward the front handle 4. Loosen and remove the bar nuts and the clutch cover from the saw 5. An adjusting pin and screw are used to adjust the tension of the chain. It is very important when assembling the bar that the adjusting pin aligns in a hole in the bar. Turning the screw will move the adjusting pin up and down the screw.
PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.
