Quad-Monitor Stand ARMBARQUAD *actual product may vary from photos FR: Guide de l’utilisateur - fr.startech.com DE: Bedienungsanleitung - de.startech.com ES: Guía del usuario - es.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com IT: Guida per l’uso - it.startech.com For the latest information, technical specifications, and support for this product, please visit www.StarTech.com/ARMBARQUAD.
Use of Trademarks, Registered Trademarks, and other Protected Names and Symbols PHILLIPS® is a registered trademark of Phillips Screw Company in the United States or other countries. This manual may make reference to trademarks, registered trademarks, and other protected names and/or symbols of third-party companies not related in any way to StarTech.com. Where they occur these references are for illustrative purposes only and do not represent an endorsement of a product or service by StarTech.
Warning statements 注意 Make sure to assemble this product according to the instructions. Failure to do so might result in personal injury or property damage. 必ず取扱説明書に従って本製品の組み立てを行って下さい。取り扱いを誤った場合に、傷害を負う恐れ や物的損害が発生する恐れがあります。 Make sure that the weight of the monitor doesn’t exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the equipment. This product can support the following weight: 8 kg (17.6 lb.) per monitor mount.
Table of Contents Warnings....................................................................................................................................................... i Introduction.............................................................................................1 Product diagram......................................................................................................................................... 1 Technical specifications.............................................
Introduction Product diagram VESA monitor mount VESA monitor mount Crossbar Cable-management clip Cable-management clips Upper pole VESA monitor mount VESA monitor mount Crossbar Pole connector Cable-management clip Cable-management clips Lower pole Baseplate Instruction manual 1
Technical specifications Type of measurement Measurement VESA mounting hole pattern 75x75 100x100 Weight capacity Up to 8 kg (17.6 lb.) per monitor mount kg Tilt +450 to -450 Screen size Between 330 mm and 686 mm (13 in. and 27 in.
Package contents 1 2 Baseplate Crossbars Qty: One Qty: Two 4 3 Lower pole Upper pole Qty: One Qty: One 5 6 Pole connector Cable-management clips Qty: One Qty: Two Instruction manual 3
7 Cap 3 mm hex key Qty: One Qty: One 9 10 5 mm hex key 6 mm hex key Qty: One Qty: One 12 11 M4x12 mm screws M5x12 mm screws Qty: Sixteen Qty: Sixteen Instruction manual 4
13 14 Washers Instruction manual Qty: Sixteen Qty: One Requirements • Four monitors or displays that are compatible with one of the mounting hole patterns that ARMBARQUAD supports • A Phillips screwdriver Requirements are subject to change. For the latest requirements, please visit www.StarTech.com/ARMBARQUAD.
Assembly Warning! Make sure that the combined weight of the monitors does not exceed the weight capacity of this product. If you exceed the weight capacity, you might experience personal injury or damage to the product. This product can support the following weight: 8 kg (17.6 lb.) per monitor mount. Assemble the lower pole 1. Thread the cable-management clip onto the pole. 2. Thread the cap onto the pole. 3. Screw the pole into the baseplate.
Attach a crossbar 1. Use the 3 mm hex key to loosen the screw in the side of the collar on the lower pole, and raise or lower the collar on the pole. 2. When the collar is at the desired height, use the 3 mm hex key to tighten the screw in the side of the collar. (figure 3) figure 3 Collar 3 mm hex key Lower pole 3. Slide one of the crossbars down the pole so that it sits against the collar.
4. Use the 5 mm hex key to tighten the screw at the back of the crossbar. (figure 5) figure 5 5 mm hex key Crossbar Attach the upper pole 1. Screw the pole connector onto the lower pole. 2. Thread the other cable-management clip onto the upper pole. 3. Screw the upper pole into the pole connector.
4. Use the 3 mm hex key to tighten the two screws in the side of the pole connector. (figure 7) figure 7 3 mm hex key Pole connector Attach the second crossbar 1. Use the 3 mm hex key to loosen the screw in the side of the collar on the upper pole, and raise or lower the collar on the pole. 2. When the collar is at the desired height, use the 3 mm hex key to tighten the screw in the side of the collar.
3. Slide the other crossbar down the pole so that it sits against the collar. (figure 9) figure 9 Crossbar Collar Upper pole 4. Use the 5 mm hex key to tighten the screw at the back of the crossbar.
Attach monitors to the crossbars Warning! Attaching the monitors is a two-person job. Do not attempt to complete this task by yourself. Tipping hazard! The ARMBARQUAD is free-standing and when you attach monitors to it, you increase the tipping hazard. A second person is required to keep the ARMBARQUAD upright as you attach the monitors. ARMBARQUAD is designed to be used with monitors that are the same size and weight.
3. Carefully hook the screws into the top two slots on the VESA monitor mount on the crossbar. (figure 12) figure 12 M4x12 mm screw or M5x12 mm screw VESA monitor mount Crossbar 4. Use a Phillips screwdriver to tighten the screws. (figure 13) Caution! If the crossbar starts to slip down the pole when you add the weight of the monitor, remove the monitor and use the 5 mm hex key to tighten the screw in the back of the crossbar. When the screw is tightened, repeat step 3 to reattach the monitor.
5. Place two washers over the lower mounting holes in the VESA monitor mount. 6. Insert two M4x12 mm screws or M5x12 mm screws through the washers, the mounting holes in the VESA monitor mount, and into the back of the monitor. (figure 14) Warning! Do not over-tighten the screws. If you encounter resistance while you’re tightening the screws, stop tightening. Failure to do so could result in damage to the monitor. 7.
2. While someone holds the monitor in place, insert the M4x12 mm screws or M5x12 mm screws through the washers, the mounting holes in the VESA monitor mount, and into the back of the monitor. (figure 15) 3. Use a Phillips screwdriver to tighten the screws. Caution! If the crossbar starts to slip down the pole when you add the weight of the monitor, remove the monitor and use the 5 mm hex key to tighten the screw in the back of the crossbar.
Adjust the tilt angle of your monitor 1. To change the angle that the monitor is tilted at, use the 6 mm hex key to loosen the screw in the side of the VESA monitor mount. 2. Position the monitor at the angle that works best for you. 3. Use the 6 mm hex key to turn the screw clockwise to tighten it. (figure 16) figure 16 +45° -45° 6 mm hex key Screw 4. When you’re done adjusting the tilt angle, you can store the 5 mm hex key and the 6 mm hex key holder in the cable-management clip.
Tipping hazard warning Warning! The most stable configuration of the ARMBARQUAD is in the “flat” position, with each set of monitors positioned in a straight line. Depending upon the forward and rear positioning of the monitors, ARMBARQUAD can become unstable. If you adjust the position of the monitors, you do so at your own risk, and you should exercise caution and test the stability of the ARMBARQUAD before you use it in the adjusted configuration.
• To raise or lower the left and right monitors minutely, use the adjustment screws located on the top of the VESA monitor mounts.
Technical support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty information This product is backed by a two-year warranty. StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
