Desk Mount Monitor Arm with Cable Management & Height Adjust ARMPIVOT *actual product may vary from photos DE: Bedienungsanleitung - de.startech.com FR: Guide de l'utilisateur - fr.startech.com ES: Guía del usuario - es.startech.com IT: Guida per l'uso - it.startech.com NL: Gebruiksaanwijzing - nl.startech.com PT: Guia do usuário - pt.startech.com For the most up-to-date information, please visit: www.startech.
FCC Compliance Statement This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Table of Contents Introduction.............................................................................................1 Packaging Contents.................................................................................................................................. 1 Product Diagram.....................................................................................2 Installation...............................................................................................2 Desk / Grommet Mounting.
Introduction Packaging Contents 1 2 3 4 5 6 Thumb Screws Qty: 4 EVA Cushion Qty: 1 7 8 Cable Clip / Collar (attached) Qty: 1 10 M4x15mm Phillips Screw Qty: 1 13 Instruction Manual Small C Clamp Qty: 1 9 M6x12mm Phillips Screws Qty: 4 M5x14mm Hex Screws Qty: 4 11 12 Male Round Washer Qty: 1 14 Hand Screw (attached) Qty: 1 Large C Clamp Qty: 1 Monitor Mount Qty: 1 Support Post Qty: 1 Female Round Washer Qty: 1 15 Pressure Plate (attached) Qty: 1 1 M3 (2.
Product Diagram Installation Warning: It is the installer’s responsibility to ensure that the combined weight of all components does not exceed the maximum 14 kg (30.9 lbs) weight capacity of the mounting arm. Desk / Grommet Mounting The Monitor Arm can be clamped to a desk / table, or mounted through a grommet hole. Instructions for both will be provided in the following sections.
Grommet Mount 1. Remove the Hand Screw (13) from the base of the Support Post (1). 2. Place the EVA Cushion (4) beneath the Support Post (1) and thread the Hand Screw (13) from below until secure. Ensure that the Pressure Plate (14) is making full contact with the desk surface. Desk Mount 1. Attach the Large C Clamp (3) and Small C Clamp (6) pieces using 4 M6x12mm Screws (8) as shown, depending on the thickness of your desk / table.
2. Slide the Hand Screw (13) through the bottom of the clamp and attach the Pressure Plate (14) using the Male Round Washer (11), Female Round Washer (12) and M4x15mm Phillips Screw (10). 3. Attach the completed Desk Clamp to base of the Support Post (1) using 4 M5x14mm Hex Screws (9). 4. Place the EVA Cushion (4) beneath the Support Post (1) and then place the Desk Clamp opening around the edge of your desktop in your desired location.
Attaching the Display 1. Carefully place your display face down on a protective surface to access the mounting points. 2. Attach the display to the Monitor Mount (2) using the 4 Thumb Screws (5).
WARNING! Do not over-tighten the screws and stop immediately if you encounter resistance to avoid damage to your display. Ensure that all spacers and screws being used are the same length and thread type. Completing the Assembly 1. Loosen the Cable Clip / Collar (7) on the Support Post (1) and adjust to the desired height. 2. Slide the Monitor Mount (2) onto the Support Post (1) until it rests on the Collar (7) and tighten the set screw using the M3 Allen Wrench (15).
Adjusting Monitor Mount Resistance WARNING! Forced movement of the Mount Bracket without loosening the screws may damage the product or the mounted displays. Always support your display from underneath when making any adjustments to the LCD Arms or Mount Brackets to avoid damage to the display. Note: For all adjustments outlined below, turning the screw clockwise will increase the resistance, while turning the screw counter-clockwise will decrease resistance.
Specifications Weight Capacity 30.
Technical Support StarTech.com’s lifetime technical support is an integral part of our commitment to provide industry-leading solutions. If you ever need help with your product, visit www.startech.com/support and access our comprehensive selection of online tools, documentation, and downloads. For the latest drivers/software, please visit www.startech.com/downloads Warranty Information This product is backed by a two year warranty. In addition, StarTech.
Hard-to-find made easy. At StarTech.com, that isn’t a slogan. It’s a promise. StarTech.com is your one-stop source for every connectivity part you need. From the latest technology to legacy products — and all the parts that bridge the old and new — we can help you find the parts that connect your solutions. We make it easy to locate the parts, and we quickly deliver them wherever they need to go. Just talk to one of our tech advisors or visit our website.
